Cisco NM-16ESW - EtherSwitch Switch Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco NM-16ESW manuals!
Problems with Cisco NM-16ESW?
Ask a Question
Free Cisco NM-16ESW manuals!
Problems with Cisco NM-16ESW?
Ask a Question
Cisco NM-16ESW Videos
Cisco NM-16ESW $550 Price Reduction
Duration: :34
Total Views: 5
Duration: :34
Total Views: 5
Cisco NM-16ESW-1GIG We buy and sell new and used Cisco
Duration: :46
Total Views: 87
Duration: :46
Total Views: 87
Cisco NM-16ESW-1GIG $550 Price Reduction
Duration: :34
Total Views: 3
Duration: :34
Total Views: 3
Popular Cisco NM-16ESW Manual Pages
User Guide - Page 1
... 36-Port Ethernet Switch Module (NM-16ESW and NM-36ESW) for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Feature History Release 12.2(2)XT
12.2(8)T 12.2(15)ZJ
Modification
This feature was integrated into Cisco IOS Release 12.2(8)T. and 36-Port Ethernet Switch Module, page 130 • Command Reference, page 157 • Glossary, page 242
Cisco IOS Release 12...
User Guide - Page 5
... Layer 3 characteristics configured on a router; Routed ports support only CEF switching (IP fast switching is not limited by putting the interface into Layer 3 mode, you return the interface to the switch. With VTP, you use VTP in your network. Additional SVIs must decide whether to route between VLANs, fallback-bridge nonroutable protocols between this command to the...
User Guide - Page 7
... is correct, its other trunks, even for TLVs it is supported in the NM-16ESW software, VTP version 2 forwards VTP messages in the domain enable VTP version 2
• The Cisco IOS end and Ctrl-Z commands are version 2-capable. 16-
If the digest on a switch, all version 2-capable switches in transparent mode, without consistency checks.
The unrecognized TLV...
User Guide - Page 33
... map is not supported in class maps with the ACL, you can attach a policy to classify IP traffic by using the access-list global configuration command. For more information, see the "Guidelines for the traffic by using the match class-map configuration command. and 36-port Ethernet switch network modules.
• System-defined masks are a part of a policy map...
User Guide - Page 66
... EAPOL-logoff message is set to auto for a specific interface, use the show dot1x statistics privileged EXEC command.
Returns to the default values.
To display 802.1x statistics for all interfaces, use the show dot1x privileged EXEC command. To display the 802.1x administrative and operational status for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Enabling...
User Guide - Page 67
...Exits configuration mode. 16- Step 1
Use the show spanning-tree vlan command to verify spanning tree configuration:
Router# show spanning-tree vlan 200 VLAN200 is executing the ieee compatible Spanning...change flag not set, detected flag not set Number of topology changes 0 last change occurred 01:53:48 ago Times: hold 1, topology change 24, notification 2 hello 2, max age 14, forward delay ...
User Guide - Page 68
...and 36-Port Ethernet Switch Module for an interface. Configures the VLAN port priority for an interface.
Configures the port priority for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Configuring Spanning Tree Port Priority
To configure the spanning tree port priority of an interface, use the following commands beginning in increments of this command to verify spanning...
User Guide - Page 69
... the preferred commands to restore the defaults. Use the no form of a VLAN, use the following commands in global configuration mode:
Step 1
Command
Router(config)#...configuration:
Router# show spanning-tree vlan command to 65,535. Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
69 Exits configuration mode. and 36-Port Ethernet Switch Module for an interface. Exits configuration...
User Guide - Page 71
... of this value will set to the default value of the bridge priority and the bridge MAC address, is not supported on all switches in global configuration mode:
Step 1 Step 2
Command
Router(config)# [no form of spanning tree should avoid configuring the hello time, forward delay time, and maximum age time manually after configuring the switch as the spanning...
User Guide - Page 81
... support for Cisco IOS Release 12.2.
It also does not support filtering based on the specific keywords relative to each protocol type.
You cannot reorder the list or selectively add or remove ACEs from a numbered list.
For more details on the minimize-monetary-cost type of service (TOS) bit. Note The Ethernet switch network module does not support...
User Guide - Page 93
..." section on page 32 for QoS ACLS. Only one match criterion per class map is supported. Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
93 To remove a match criterion, use the class-map global configuration command to isolate a specific traffic flow (or class) from all other traffic and to further classify it . Note You...
User Guide - Page 94
... IP packet and to set the CoS to take when the traffic is not supported.
Creates a policy map by the class class-default policy-map configuration command.
and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Classifying, Policing, and Marking Traffic by using the class-map global configuration command, specify its name for...
User Guide - Page 108
... a challenge. Setting the bits to provide marking can automatically configure voice VLAN. This configuration approach must also use the following commands beginning in all media streams to an IP Precedence value of 5. (With Cisco CallManager Release 3.0(5), this is one of the simpler ways to provide Class of Service (CoS) marking.
Voice Traffic and VVID
The Ethernet switch network...
User Guide - Page 138
... resulting configuration will not display the command you entered to enable spanning tree. 16- The following example shows spanning tree being disabled on the NM-16ESW:
Router# clear cdp counters
138
Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Configuration Examples...
User Guide - Page 161
... policy map to the egress direction.
Defaults
No policy-map class maps are available: • default: sets a command to the class map and its default. The class command performs the same function as configured by using the service-policy interface configuration command;
Note In a policy map, the class named class-default is 100 to 199 and 2000 to...
Cisco NM-16ESW Reviews
We have not received any reviews for Cisco yet.