User Guide
Page 2
...IPS-4260 uses a flash device for IPS-4260 is also inline ready. IPS-4260 monitors greater than a hard-disk drive. The 1-Gbps performance is Gigabit-Ethernet0/1. IPS-4260 ships with one power supply, but it supports redundant power supplies. Note IPS-4260 operates in sensing interface is traffic combined from right to left as shown in Figure 6-4 on sensor interfaces, see Sensor...system running Cisco IPS 5.1 software. Note Only expansion slots 2 and 3 are supported at this time. IPS-4260 supports two optional network interface cards, the 2SX Fiber card, and the 4GE bypass ...
...IPS-4260 uses a flash device for IPS-4260 is also inline ready. IPS-4260 monitors greater than a hard-disk drive. The 1-Gbps performance is Gigabit-Ethernet0/1. IPS-4260 ships with one power supply, but it supports redundant power supplies. Note IPS-4260 operates in sensing interface is traffic combined from right to left as shown in Figure 6-4 on sensor interfaces, see Sensor...system running Cisco IPS 5.1 software. Note Only expansion slots 2 and 3 are supported at this time. IPS-4260 supports two optional network interface cards, the 2SX Fiber card, and the 4GE bypass ...
User Guide
Page 3
..., page 6-4 OL-8677-01 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 6-3 Figure 6-1 4GE Bypass Interface Card Hardware Bypass 153325 190474 • 2SX Card (part number IPS-2SX-INT=) Provides two 1000BASE-SX ...(fiber) monitoring interfaces (allowing up to 4 total fiber monitoring interfaces). Figure 6-2 2SX Interface Card Hardware Bypass This section describes the 4GE bypass interface card and its configuration restrictions. Figure 6-2 shows the 2SX card. Chapter 6 Installing IPS-4260 Figure 6-1 shows the 4GE...
..., page 6-4 OL-8677-01 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 6-3 Figure 6-1 4GE Bypass Interface Card Hardware Bypass 153325 190474 • 2SX Card (part number IPS-2SX-INT=) Provides two 1000BASE-SX ...(fiber) monitoring interfaces (allowing up to 4 total fiber monitoring interfaces). Figure 6-2 2SX Interface Card Hardware Bypass This section describes the 4GE bypass interface card and its configuration restrictions. Figure 6-2 shows the 2SX card. Chapter 6 Installing IPS-4260 Figure 6-1 shows the 4GE...
User Guide
Page 4
Hardware Bypass Chapter 6 Installing IPS-4260 4GE Bypass Interface card IPS-4260 supports the 4-port GigabitEthernet card (part number IPS-4GE-BP-INT=) with GigabitEthernet2/1, and both interfaces are unloaded, those paired interfaces enter fail-open state in each inline interface and between ports 2 and 3. For more inline interfaces and power down the sensor and verify that violates one...
Hardware Bypass Chapter 6 Installing IPS-4260 4GE Bypass Interface card IPS-4260 supports the 4-port GigabitEthernet card (part number IPS-4GE-BP-INT=) with GigabitEthernet2/1, and both interfaces are unloaded, those paired interfaces enter fail-open state in each inline interface and between ports 2 and 3. For more inline interfaces and power down the sensor and verify that violates one...
User Guide
Page 19
...the supported PCI cards, see Rack Mounting, page 6-9. Step 3 Step 4 Step 5 Step 6 Step 7 Power off : sensor# reset powerdown Wait for the power down IPS-4260 using IDM. For the procedure, see Supported PCI Cards, page 6-2. If you are reinstalling in an ESD Environment, page ...OL-8677-01 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 6-19 Prepare IPS-4260 to Resetting the Appliance. Power on page 6-7. Place IPS-4260 in slot 2 if you are installing only one 4GE bypass card. For the procedure, refer to be powered off IPS-4260. Note You can ...
...the supported PCI cards, see Rack Mounting, page 6-9. Step 3 Step 4 Step 5 Step 6 Step 7 Power off : sensor# reset powerdown Wait for the power down IPS-4260 using IDM. For the procedure, see Supported PCI Cards, page 6-2. If you are reinstalling in an ESD Environment, page ...OL-8677-01 Installing Cisco Intrusion Prevention System Appliances and Modules 5.1 6-19 Prepare IPS-4260 to Resetting the Appliance. Power on page 6-7. Place IPS-4260 in slot 2 if you are installing only one 4GE bypass card. For the procedure, refer to be powered off IPS-4260. Note You can ...
