Cisco 675E Support and Manuals
Popular Cisco 675E Manual Pages
Hardware Installation Guide - Page 7
...C-15 Statement 1017-Restricted Area C-25 Statement 1019-Main Disconnecting Device C-28 Statement 1024-Ground Conductor C-30 Statement 1030-Equipment Installation C-34 Statement 1040-Product Disposal C-36 Statement 1073-No User-Serviceable Parts C-38 Statement 1074-Comply with Local and National Electrical Codes C-41
78-15201-04
Cisco RPS 675 Redundant Power System Hardware Installation Guide
vii
Hardware Installation Guide - Page 10
... delivery times can also contact the Cisco service and support website for Hardware Cisco or its exclusive warranty remedy. Cisco RPS 675 Redundant Power System Hardware Installation Guide
x
78-15201-04 d. Replacement, Repair, or Refund Policy for assistance: http://www.cisco.com/public/Support_root.shtml. Cisco reserves the right to refund the purchase price as the original end user...
Hardware Installation Guide - Page 23
...; The Catalyst 3750 Switch Hardware Installation Guide • The Catalyst 3560 Switch Hardware Installation Guide • The Catalyst 3550 Multilayer Switch Hardware Installation Guide • The Catalyst 2970 Switch Hardware Installation Guide • The Catalyst 2950 Switch Hardware Installation Guide
78-15201-04
Cisco RPS 675 Redundant Power System Hardware Installation Guide
xxiii
Hardware Installation Guide - Page 25
...the power supply of up or replaced. Note The RPS 675 does not support an automatic switchover to provide backup for one redundancy, you must press the Standby/Active button on the RPS so that it is designed to the internal power supply. You must connect each device to network management software. 1 C H A P T E R
Product Overview
The Cisco RPS 675 Redundant Power System (RPS), model...
Hardware Installation Guide - Page 26
...
Cisco RPS 675 Redundant Power System Hardware Installation Guide
1-2
78-15201-04 Features
Chapter 1 Product Overview
The RPS 675 was designed to support multiple devices • RPS status information available through the network management
application on Cisco.com for a complete list of the RPS 675 and includes these features:
• Six output channels to support specific Cisco...
Hardware Installation Guide - Page 27
...-pin connector cable (CAB-RPS-1614=) to allow connection to provide maximum wiring closet port density
• Two output levels:
- -48 VDC with a maximum output of 375 W
- 12 VDC with a maximum output of 300 W
The two output levels provide a maximum total output power of the colors.
78-15201-04
Cisco RPS 675 Redundant Power System Hardware Installation Guide
1-3
Hardware Installation Guide - Page 29
...Cisco RPS 675 Redundant Power System Hardware Installation Guide
1-5
The DC output power is not powered up. TEMP
The RPS 675 is not functioning correctly.
A device is approaching an overtemperature condition. The RPS 675 internal power supplies are numbered 1 to 6, which corresponds to the numbers on the DC outputs.
powered up . The output LEDs are up .
The RPS 675...
Hardware Installation Guide - Page 30
... green. When you connect devices. Cisco RPS 675 Redundant Power System Hardware Installation Guide
1-6
78-15201-04 The RPS is in standby mode or in standby mode every time you connect a device to it powers up , or if the RPS does not immediately sense that the device power supply was supplying power. It must be available as a backup power source for other connected devices...
Hardware Installation Guide - Page 38
...section includes specific regulatory statements about the Cisco 675 RPS.
U.S. Preparing for this product is in residential environment, it may cause radio frequency interference, under such circumstances, the user may be requested to take appropriate countermeasures. Always check. U.S.A. regulatory information for Installation
Chapter 2 Installation
Warning No user-serviceable parts inside...
Hardware Installation Guide - Page 49
... the screw. Connect one end of an RPS connector cable (CAB-RPS-1614=) to AC power, press the Standby/Active button on a desktop or in its correct orientation.
78-15201-04
Cisco RPS 675 Redundant Power System Hardware Installation Guide
2-15 We advise you to its own power. Statement 1
With the RPS 675 on the RPS to put it changes from the AC...
Hardware Installation Guide - Page 50
...PLUGGABLE
DC OUTPUT 4
DC OUTPUT 5
DC OUTPUT 6
Chapter 2 Installation
86669
Warning Attach only the Cisco RPS (model PWR675-AC-RPS-N1) to an AC power source. Statement 100C
Step 3
Step 4 Step 5
Connect the other end of the RPS connector cable to an AC power source.
2-16
Cisco RPS 675 Redundant Power System Hardware Installation Guide
78-15201-04 Connect all supported devices to the...
Hardware Installation Guide - Page 56
... CAN/CSA 22.2 No. 60950 IEC 60950/EN 60950 AS/NZS 3260, TS001 CE CCC approval pending CLEI code NOM
EMC FCC Part 15 Class A BSMI EN 55022: 1998 (CISPR22) Class A EN 55024: 1998 (CISPR24) VCCI Class A AS/NZS 3548 Class A CE CNS 13438 Class A MIC
Cisco RPS 675 Redundant Power System Hardware Installation Guide
A-2
78-15201-04
Hardware Installation Guide - Page 59
..., page C-34 • Statement 1040-Product Disposal, page C-36 • Statement 1073-No User-Serviceable Parts, page C-38 • Statement 1074-Comply with Local and National Electrical Codes,
page C-41
Cisco RPS 675 Redundant Power System Hardware Installation Guide
C-1 C A P P E N D I X
Translated Safety Warnings
78-15201-04
This appendix repeats in multiple languages the warnings...
Cisco 675E Reviews
Do you have an experience with the Cisco 675E that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!