Cisco 2613 Support and Manuals
Popular Cisco 2613 Manual Pages
Hardware Installation Guide - Page 20
... divider. (See the "Removing Slot Dividers" section on multiple Cisco IOS releases. Cisco MWR 1941-DC routers support single-wide network modules only. Cisco Network Modules Hardware Installation Guide
1-6
OL-2485-20
If you do not have an account or have an account on Cisco.com. Cisco MWR 1941-DC 1 routers
Single-wide Slot 1
Only two NM-36ESW network modules...
Hardware Installation Guide - Page 40
...
Connecting Cisco EtherSwitch Service Modules
Connecting Cisco EtherSwitch Service Modules
Connecting Cisco EtherSwitch Service Modules
Connecting Ethernet, Fast Ethernet, and Token Ring Network Modules Connecting Ethernet, Fast Ethernet, and Token Ring Network Modules Connecting Ethernet, Fast Ethernet, and Token Ring Network Modules
1-26
Cisco Network Modules Hardware Installation Guide
OL...
Hardware Installation Guide - Page 41
...-SMF)
Supported on Cisco Routers
See Section
Cisco 2691 Cisco 3600 series Cisco 3700 series
Connecting Ethernet, Fast Ethernet, and Token Ring Network Modules
Cisco 2691 Cisco 3700 series Cisco 3800 series
Connecting Ethernet, Fast Ethernet, and Token Ring Network Modules
Cisco 3600 series
Note Not supported on Cisco 3630 routers
Connecting Ethernet, Fast Ethernet, and Token Ring Network...
Hardware Installation Guide - Page 42
... Network Modules
Chapter 1 Overview of Cisco Network Modules for Cisco Access Routers
Table 1-6 Platform Support for Cisco Network Modules (continued)
Product Description
2-slot network module with 2 Fast Ethernet ports, version 2
Cisco Product ID NM-2FE2W-V2
2-slot network module with 1 Fast Ethernet port and 1 Token Ring port
NM-1FE1R2W
LAN and T1/E1 Combination Network Modules
1-port...
Hardware Installation Guide - Page 77
... 3-1 • Fast Ethernet Network Modules, page 3-5 • Token Ring Network Modules, page 3-10
Tip To determine whether your router supports a specific network module, see Figure 3-2)
Figure 3-1 1-Port Ethernet Network Module
ETHERNET
1E
ETH 0
LINK
EN
ACT
10BASE-T
AUI
port
port
H9251
OL-2485-20
Cisco Network Modules Hardware Installation Guide
3-1 and 4-port Ethernet modules, and on...
Hardware Installation Guide - Page 78
...
1E 2W W1
10BASE-T
AUI
WO
port
port
ACT LNK
H7215
AUI EN
ETHERNET 0
LEDs
Enable LED
Figure 3-4 2-Ethernet 2-WAN Card Slot Network Module
2E 2W W1
LEDs
10BASE-T
WO
port
AUI port
STP ETHERNET 1
ACT ILNK ACT LNK
AUI EN
ETHERNET 0
10BASE-T port
LEDs
Enable LED
H7213
Cisco Network Modules Hardware Installation Guide
3-2
OL-2485-20
Hardware Installation Guide - Page 81
... the router. See that the router is receiving the link integrity signal from the hub (10BASE-T only).
Figure 3-8 shows 4-port Ethernet network module LEDs as an example.
Note The Fast Ethernet-PRI modules described in Chapter 4, "Connecting Fast Ethernet-PRI Network Modules," also provide a Fast Ethernet interface.
Chapter 3 Connecting Ethernet, Fast Ethernet, and Token Ring Network...
Hardware Installation Guide - Page 82
... card slot network modules (NM-1FE1R2W-V2) only to intrabuilding or nonexposed wiring or cabling. Cisco Network Modules Hardware Installation Guide
3-6
OL-2485-20 Caution
To comply with the Telcordia GR-1089 NEBS standard for a sample faceplate.
• 1-Fast Ethernet 1-Token Ring 2-WAN card slot network module (NM-1FE1R2W and NM-1FE1R2W-V2). See Figure 3-13...
Hardware Installation Guide - Page 84
...type fiber-optic cables are widely available commercially. Cisco Network Modules Hardware Installation Guide
3-8
OL-2485-20 Cisco Systems does not supply these cables. The intrabuilding cable must be shielded and the shield must be grounded at both ends. Fast Ethernet Network Modules
Chapter 3 Connecting Ethernet, Fast Ethernet, and Token Ring Network Modules
Note RJ-45 cables are not...
Hardware Installation Guide - Page 85
... b FX EN
SC-type connector
Fast Ethernet module
Router
Figure 3-18 Connecting a Fast Ethernet FX Port to a Repeater or Hub (Simplex Connectors)
H10843
ACT C0L LINK 100 MBPS FULL DPLX
ETHERNET 0
WO SERIAL
FAST ETHERNET 1FE-FX
100 b FX EN
To repeater or hub
SC-type connectors
Fast Ethernet module
Router
OL-2485-20
Cisco Network Modules Hardware Installation Guide
3-9
Hardware Installation Guide - Page 86
... is occurring on the network. Token Ring Network Modules
The following network modules provide Token Ring interfaces: • 1-port Ethernet 1-port Token Ring 2-WAN card slot module (NM-1E1R2W) (see Figure 3-20) • 1-port Fast Ethernet 1-port Token Ring 2-WAN card slot module (NM-1FE2R2W) (see Figure 3-21)
3-10
Cisco Network Modules Hardware Installation Guide
OL-2485-20 Figure 3-19...
Hardware Installation Guide - Page 87
... is in use. To connect the module to a Token Ring network, attach one end of the cable to the DB-9 connector on the network module (see Figure 3-23). OL-2485-20
Cisco Network Modules Hardware Installation Guide
3-11 Only one RJ-45 connector for an STP Token Ring connection and one connector can be active at a time...
Hardware Installation Guide - Page 88
... 802.5 connector
Figure 3-23 Connecting a Token Ring UTP Port (RJ-45) to an MAU
Unshielded Token Ring lobe cable (not provided)
1FE 1R2W
W1
TOKEN RING 0
FAST ETH 0
IN-RING 16Mbps FDX LINK 100 Mbps FDX
WO EN
Token Ring UTP port (RJ-45)
Media attachment unit
26714
Standard IEEE 802.5 connector
3-12
Cisco Network Modules Hardware Installation Guide
OL-2485-20
Hardware Installation Guide - Page 89
... off , the
interface is available to the router.
OL-2485-20
Cisco Network Modules Hardware Installation Guide
3-13 If it is inserted into the ring. The 1-Ethernet 1-Token Ring 2-WAN card slot network module and the 1-Fast Ethernet 1-Token Ring 2-WAN card slot network module both have an enable (EN) LED. The 1-Fast Ethernet 1-Token Ring 2-slot network module also has the FDX LED...
Cisco 2613 Reviews
Do you have an experience with the Cisco 2613 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!