Cisco 2523 Support and Manuals
Get Help and Manuals for this Cisco item
Popular Cisco 2523 Manual Pages
Getting Started Guide - Page 3
... access points and the Cisco Wireless Control System (WCS) to the manufacturer's instructions.
Contact the appropriate electrical inspection authority or an electrician if you are mounted in conjunction with a minimum of used batteries according to provide system-wide wireless LAN functions. Statement 1040
Safety Considerations
• Verify that suitable grounding is replaced...
Getting Started Guide - Page 5
... controller configures the RS-232 port as a console port with default settings of 1200, 2400, 4800, 9600, 19200, 38400, 57600, and 115200. The boot-loader supports baud rates of 9600, N, 8, 1.
Figure 2 shows the front panel and location of the LED manufacturer's specifications and is not a defect. This is within the normal range of...
Getting Started Guide - Page 9
... is damaged or missing, notify your authorized Cisco sales representative.
Controller with factory-supplied power cord and mounting hardware - VT-100 terminal emulator on a desk, shelf, or wall...and information before you can install the controller: • Wireless controller hardware - Check each item for damage. Network, operating system service network, and access point cables as required ...
Getting Started Guide - Page 10
... interface default router IP address,...servers use the same communication port. Cisco uses an integral TFTP server. Initial System Configuration Information
Obtain the following initial configuration parameters from clients, either Yes or No.
- No is more convenient, but has higher security and works well for downloading operating system software updates).
• Local TFTP server...
Getting Started Guide - Page 13
...Cisco. Failure to use the correct hardware or to follow these steps:
Step 1 Attach the 19-inch brackets to each side of space around the controller ventilation openings to the Network
For configuration instructions about using the CLI setup...
Read the wall-mounting carefully before beginning installation.
Step 3 Place the switch on a wall using an optional rack-mount bracket kit that ...
Getting Started Guide - Page 18
Step 6 For configuration instructions about using the CLI setup program, see the "Running the Bootup Script and Power-On Self Test" section on page 23. Statement 1006
To install the controller in a ...Figure 9 with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Warning
To prevent bodily injury when mounting or servicing this unit in a partially ...
Getting Started Guide - Page 24
...using...= 254:4 disrupt level = header
24 Model: 1GB CompactFlash Card Firm: CF B612J ...cisco) Board Revision 0.0 (SN: PSJ143302MT, Type: AIR-CT2504-K9) (P) Verifying boot loader integrity... Manually update images Enter selection:
If you did not press Esc, the boot process continues and takes two to access the Boot Menu...
The bootup script displays operating system software initialization (code...
Getting Started Guide - Page 25
... Access Control List Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting Licensing Services: ok Starting LWAPP: ok Starting CAPWAP: ok Starting LOCP: ok Starting Security Services: ok
25 All rights reserved. Cisco AireOS Version 7.0.114.76 Firmware...
Getting Started Guide - Page 26
...: ok Starting SSHPM LSC PROV LIST: ok Starting RRC Services: ok Starting FMC HS: ok Starting Management Services:
Web Server: ok CLI: ok
Secure Web: Web Authentication Certificate not found (error).
License Agent: ok
(Cisco Controller)>
Step 4 If desired, press Esc key to interrupt the boot process and access the Boot menu.
26 If you cannot...
Getting Started Guide - Page 27
... such device or address readCPUConfigData: cardid 0x6060001 Cisco is a trademark of Cisco Systems, Inc. Loading primary image (7.0.114.76) 100% 31427987 bytes read Launching images... Change active boot image 4. Manually update images
Enter selection:
If you did not press Esc, the boot process continues and takes two to access the following menu:
1. All rights reserved...
Getting Started Guide - Page 28
...: ok Starting Policy Manager: ok Starting Data Transport Link Layer: ok Starting Access Control List Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok Starting Management Frame Protection: ok Starting Certificate Database: ok Starting VPN Services: ok Starting Licensing Services: ok Starting LWAPP: ok Starting CAPWAP: ok Starting LOCP: ok Starting Security...
Getting Started Guide - Page 29
...access management interface via HTTPS please reconfigure Virtual Interface. Note If you enter an incorrect response, the controller provides you can use the startup wizard, you for a login ID and password. License Agent: ok
(Cisco... wizard information you can use to the wizard prompt.
29 Using the Startup Wizard
Before you with an appropriate error message such as invalid response...
Getting Started Guide - Page 30
... services such as AAA servers. The VLAN identifier should be assigned to match the switch interface configuration. Ports values are 1 to 4]
Note There is the name you need to return to this controller.
Enter the administrative password to be set to this controller. The management interface is admin.
You can access the controller GUI interface using...
Getting Started Guide - Page 31
... you want the controller to belong.
Network Name (SSID)
Enter the network name, or service set identifier (SSID).
The following message appears:
Warning!
You should enter a fictitious, unassigned IP address, such as guest web authentication and VPN termination. Please see documentation for more details.
31 Virtual Gateway IP Address
Enter the IP address...
Getting Started Guide - Page 37
.../whatsnew.html Subscribe to your desktop using a pointed object, such as a Really Simple Syndication (RSS) feed and set content to be delivered directly to the What's New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at the prompts. The RSS feeds are a free service and Cisco currently supports RSS Version 2.0.
37
Cisco 2523 Reviews
We have not received any reviews for Cisco yet.