Setup Guide
Page 2
Setup Guide This guide provides information for setting up a network connection for Connection Cable Connection Printer Setup Troubleshooting Network Connection Wireless Connection Preparation for Connection Connection Using WPS Wired Connection Preparation for the printer.
Setup Guide This guide provides information for setting up a network connection for Connection Cable Connection Printer Setup Troubleshooting Network Connection Wireless Connection Preparation for Connection Connection Using WPS Wired Connection Preparation for the printer.
Setup Guide
Page 3
...hoc connection," which establishes a direct connection to prepare an access point. Notes on your personal information to a third party. • This printer cannot be used as your system environment. Network Connection Wireless Connection a Preparation for your device to something other than WEP and TKIP or ...as a security protocol. For details, refer to the manual of the network device vary depending on Wireless Connection • Make sure that the printer is turned on , the POWER lamp (A) will be used over a wireless connection without an access point, is set to . •...
...hoc connection," which establishes a direct connection to prepare an access point. Notes on your personal information to a third party. • This printer cannot be used as your system environment. Network Connection Wireless Connection a Preparation for your device to something other than WEP and TKIP or ...as a security protocol. For details, refer to the manual of the network device vary depending on Wireless Connection • Make sure that the printer is turned on , the POWER lamp (A) will be used over a wireless connection without an access point, is set to . •...
Setup Guide
Page 4
b Connection Using WPS 1. Make sure that the (blue) Wi-Fi lamp and POWER lamp are ready to press the button on the access point within 2 minutes. 3. The network connection setup is lit as shown in the illustration above, then press and hold the Wi-Fi button (A) on the printer when you are lit. Make sure that the (blue) Wi-Fi lamp flashes quickly and the POWER lamp is now complete. Press and hold the button on the access point. 2.
b Connection Using WPS 1. Make sure that the (blue) Wi-Fi lamp and POWER lamp are ready to press the button on the access point within 2 minutes. 3. The network connection setup is lit as shown in the illustration above, then press and hold the Wi-Fi button (A) on the printer when you are lit. Make sure that the (blue) Wi-Fi lamp flashes quickly and the POWER lamp is now complete. Press and hold the button on the access point. 2.
Setup Guide
Page 5
... computer and router (A) (or access point) are connected. • The configuration, router functions, setup procedures and security settings of the printer. If the power is turned on your personal information to the LAN side (same network segment). Remove the Cap (A) from the upper port located ...on the right side at the same time. • When using a router, connect the printer and computer to a third party. • This printer cannot be lit. Notes on , the POWER lamp (A) will need an Ethernet cable (sold separately). 1. Make sure that the...
... computer and router (A) (or access point) are connected. • The configuration, router functions, setup procedures and security settings of the printer. If the power is turned on your personal information to the LAN side (same network segment). Remove the Cap (A) from the upper port located ...on the right side at the same time. • When using a router, connect the printer and computer to a third party. • This printer cannot be lit. Notes on , the POWER lamp (A) will need an Ethernet cable (sold separately). 1. Make sure that the...
Setup Guide
Page 6
Please make sure to the USB port. Do not connect it to use the correct port on the printer until the POWER lamp flashes 11 times, then release the RESUME/CANCEL button after the eleventh flash. Connect the printer and a network device (router, etc.) with an Ethernet cable (A). The wired connection setup is now complete. The network connection setup is complete. c Printer Setup 1. Hold down the RESUME/CANCEL button (A) on the back of the printer. 2.
Please make sure to the USB port. Do not connect it to use the correct port on the printer until the POWER lamp flashes 11 times, then release the RESUME/CANCEL button after the eleventh flash. Connect the printer and a network device (router, etc.) with an Ethernet cable (A). The wired connection setup is now complete. The network connection setup is complete. c Printer Setup 1. Hold down the RESUME/CANCEL button (A) on the back of the printer. 2.
Setup Guide
Page 7
...• Is the network device (router, etc.) turned on? After checking the above points, wait for a while, then bring the access point and printer close to the manual supplied with the access point or contact its manufacturer. When the (blue) Wi-Fi lamp flashes quickly and the... specified time. For details on . • Are the computer and network device configured? • Are the access point and printer installed in an open space where wireless communications are possible? • Is the access point operating in IEEE802.11n (2.4 GHz), IEEE802.11g or IEEE802.11b...
...• Is the network device (router, etc.) turned on? After checking the above points, wait for a while, then bring the access point and printer close to the manual supplied with the access point or contact its manufacturer. When the (blue) Wi-Fi lamp flashes quickly and the... specified time. For details on . • Are the computer and network device configured? • Are the access point and printer installed in an open space where wireless communications are possible? • Is the access point operating in IEEE802.11n (2.4 GHz), IEEE802.11g or IEEE802.11b...
