Brother International JS60 Support and Manuals
Get Help and Manuals for this Brother International item
View All Support Options Below
Free Brother International JS60 manuals!
Problems with Brother International JS60?
Ask a Question
Free Brother International JS60 manuals!
Problems with Brother International JS60?
Ask a Question
Popular Brother International JS60 Manual Pages
Operation Manual - Page 5
... YOUR SEWING MACHINE 7
Connecting plugs 7 Main power and sewing light switch 8 Foot controller 8 Checking the needle 8 Replacing the needle 8 Changing the presser foot 10
THE CONTROLS 11
Pattern selection dial 11 Stitch length dial 11 Reverse sewing lever 12
THREADING THE MACHINE 13
Winding the bobbin 13 Lower threading 15 Lower threading (for models equipped with a quick-set...
Operation Manual - Page 6
...
Part Code Americas Others
1 Zigzag foot "J" (on the machine model. Part Code Americas Others 3-piece set: XE5328-001 2-piece set (90/14 needle)
5 Screwdriver
6 Foot controller
Note
● The included accessories vary depending on machine)
XC4901-121
2 Zipper foot "I
5.
6.
Part Name
7 1/4-inch Quilting Foot
8 Narrow Hemmer Foot
9 Blind Stitch Foot
10 Quilting guide
Part Code...
Operation Manual - Page 7
... on certain models.)
9 Quick-set bobbin (Page 16, 21) (This is being used when winding the thread onto the bobbin and then threading the machine.
4 Thread take-up lever (Page 18)
5 Hole for extra spool pin (Page 26) This holds a second spool of thread for 220-240V area
The foot controller part code differs depending...
Operation Manual - Page 8
...sewing machine is not to your authorized Brother Service Center for repairs before continuing use extension cords or multi-plug adapters with wet hands. If it from the machine • After using the machine...plug is intended to install the proper outlet. If the plug does not fit fully in any way.
7
KNOWING YOUR SEWING MACHINE
USING YOUR SEWING MACHINE
WARNING
● ...
Operation Manual - Page 9
...(bobbin cover, glass, etc.)
Replacing the needle
CAUTION
● Always turn on the machine while pressing down lightly, the machine will stop.
1
2
1 ...sew with product code 888-X62/X72.
The product code is not in use . Otherwise, injuries may occur if the foot controller is accidentally pressed and the machine starts sewing.
● Only use sewing machine needles for smooth sewing...
Operation Manual - Page 10
... stopper 3 Needle
Install the twin needle in the needle plate. Hold the needle with your left hand, and d then use excessive force when loosening or tightening the needle clamp screw, otherwise certain parts of the machine, insert the needle
until it touches the needle stopper.
KNOWING YOUR SEWING MACHINE
CAUTION
● Before replacing the needle, place...
Operation Manual - Page 12
... being used. The position needed for making a Satin Stitch (a close zigzag stitch), which can be used in making the Satin Stitch may need to be set as illustrated below. KNOWING YOUR SEWING MACHINE
THE CONTROLS
Pattern selection dial
The width of stitch width.
Operation Manual - Page 14
... the thread guide. Actual size
11.5 mm (7/16 inch)
This model
Other models
1
1 Pull the thread in the groove on this pin.
3 Bobbin
While holding the thread from the spool b with your right hand, pass the thread
toward you use the bobbin that comes with this machine or bobbins of the same type (part code: SA156...
Operation Manual - Page 15
...begins i spinning slowly, take your foot off the foot
controller.
Note
● When the sewing machine is started or the handwheel is wound around the bobbin. If you do not cut the ...Press the foot controller to the right. Then stop the machine. this is not a malfunction.
● The needle bar does not move when you follow the instructions carefully. Pass the end of the thread, f gently...
Operation Manual - Page 16
... lower thread.
• See page 13 for the details about bobbin winding.
Refer to sew, you accidentally step on using the quick-set the bobbin so the thread unrolls in the right direction.
KNOWING YOUR SEWING MACHINE
Lower threading
Install the bobbin wound with your finger, and then
pass the thread through the tension-adjusting...
Operation Manual - Page 18
... raised, the sewing machine can not be threaded. a
Raise the presser foot lever. If the upper threading is set incorrectly, the thread may bend or break.
● Never use a thread weight of needles and threads, refer to break.
1
1 Mark on the handwheel
CAUTION
● When threading the upper thread, carefully follow the instructions. CAUTION...
Operation Manual - Page 19
... thread guide
53
Make sure you guide the thread through g the thread take-up lever from right to left
as shown in the following illustration.
1
Thread the needle from the spool e with your sewing machine is ... cause sewing problems.
18
While holding the
1
• Make sure that the mark on the thread guide.
• The thread can not be passed behind the needle bar thread guide by ...
Operation Manual - Page 20
...steps a to h from you).
KNOWING YOUR SEWING MACHINE
Using the needle threader (for models equipped with a needle threader)
This feature ...
While lowering the needle threader lever, d hook the thread onto the guide.
2
1
1 Needle holder 2 Needle threader lever
1 2
3
1 Needle holder 2 Needle threader lever 3 Guide
Pull down the needle threader lever as e much as transparent nylon thread...
Operation Manual - Page 22
...For models equipped with a quick-set bobbin
You can begin sewing ...Replace the bobbin cover.
Draw up the lower thread as described in c the previous steps a to draw up the b lower thread.
1 2
1
• The bobbin cover should still be left over.
Before you (counterclockwise) by hand so that some thread will be removed. Pull on the upper thread to c. KNOWING YOUR SEWING MACHINE...
Operation Manual - Page 44
... retailer or the nearest authorized Brother Service Center.
The upper thread breaks. Lightly guide the fabric. Symptom
The sewing machine does not work. The needle breaks.
The needle is not appropriate for the type of the guide above the needle.)
There are pulling the fabric too much.
Visit us at " http://support.brother.com ". You have not fitted...
Brother International JS60 Reviews
We have not received any reviews for Brother International yet.