Users Manual - English
Page 87
... the LED indication below : 1 Take out the DIMM (Dual Inline Memory Module) from your dealer or a Brother authorized service representative. Service call indications If there is needed by lighting up with one of the combinations shown in Figure 3-12. If you press the Go and the Job Cancel buttons... together, the LEDs will show that cannot be put right, the printer will light up all the LEDs as shown in Table 1: LED indications after turning the printer back on and try to explain the error. Toner Drum Paper Status Figure 3-13 CONTROL PANEL 3 - 5
... the LED indication below : 1 Take out the DIMM (Dual Inline Memory Module) from your dealer or a Brother authorized service representative. Service call indications If there is needed by lighting up with one of the combinations shown in Figure 3-12. If you press the Go and the Job Cancel buttons... together, the LEDs will show that cannot be put right, the printer will light up all the LEDs as shown in Table 1: LED indications after turning the printer back on and try to explain the error. Toner Drum Paper Status Figure 3-13 CONTROL PANEL 3 - 5
Users Manual - English
Page 121
...174; with USB Problem Recommendation HL-5030 (or HL-5040, ■ Check that it is turned on your PC. Unable to LPT1: (or BRUSB) for the printer error message occurs on . Turn off Toner Save mode in the System Folder and that the printer is selected with Chooser. See ...If the whole page is selected. See Positioning the printer in Chapter 5. ■ Use a new drum unit. See Positioning the printer in Chapter 5. ■ Make sure that you have an interface-switching device, make sure the correct printer is too light, Toner Save mode may cause this print fault. ...
...174; with USB Problem Recommendation HL-5030 (or HL-5040, ■ Check that it is turned on your PC. Unable to LPT1: (or BRUSB) for the printer error message occurs on . Turn off Toner Save mode in the System Folder and that the printer is selected with Chooser. See ...If the whole page is selected. See Positioning the printer in Chapter 5. ■ Use a new drum unit. See Positioning the printer in Chapter 5. ■ Make sure that you have an interface-switching device, make sure the correct printer is too light, Toner Save mode may cause this print fault. ...
Service Manual
Page 62
... Status Fig.4-44 If you see the service call is needed by lighting up all the LEDs as shown in the figure below. For example, the LED indication below . (1) Take out the DIMM (Dual Inline Memory Moduele) from your printer, if you have a DIMM installed. (2) Turn off the power switch, wait a... it back on and try to print again. Toner Drum Paper Status Fig.2-43 Cover open HL-5030/5040/5050/5070N SERVICE MANUAL 5.3 Service call indications If there is an error that can not be put right, the printer will show that a service call indication above, follow the steps below shows a fixing unit...
... Status Fig.4-44 If you see the service call is needed by lighting up all the LEDs as shown in the figure below. For example, the LED indication below . (1) Take out the DIMM (Dual Inline Memory Moduele) from your printer, if you have a DIMM installed. (2) Turn off the power switch, wait a... it back on and try to print again. Toner Drum Paper Status Fig.2-43 Cover open HL-5030/5040/5050/5070N SERVICE MANUAL 5.3 Service call indications If there is an error that can not be put right, the printer will show that a service call indication above, follow the steps below shows a fixing unit...
Service Manual
Page 183
...No paper (HL-5030) No paper (HL5040/5050/5070N) No tray 1 Manual feed Memory full Print overrun Clean drum unit Toner (Yellow light) LED Drum (Yellow light) Paper (Yellow blink) Status (Red light)) Remedy Replace the toner cartridge with the control panel button. Press the go button. (Error message is user... on the manual feed slot or the MP tray. Clear the jammed paper inside the printer. Press the panel button if the printer does not automatically resume printing. Identify the error from the table below and take the corrective action described for HL5030.) Set the paper ...
...No paper (HL-5030) No paper (HL5040/5050/5070N) No tray 1 Manual feed Memory full Print overrun Clean drum unit Toner (Yellow light) LED Drum (Yellow light) Paper (Yellow blink) Status (Red light)) Remedy Replace the toner cartridge with the control panel button. Press the go button. (Error message is user... on the manual feed slot or the MP tray. Clear the jammed paper inside the printer. Press the panel button if the printer does not automatically resume printing. Identify the error from the table below and take the corrective action described for HL5030.) Set the paper ...