Users Manual - English
Page 109
See the instructions supplied with the new drum unit. Make sure that the Drum LED is red. Caution ■ The Drum LED indication does not disappear until you reset the drum counter. ■ Do not reset the drum counter when you replace only the toner cartridge. 8 Close the front cover. 9 Make sure that the printer is turned on, the front cover is open and the Status LED is now off. 5 - 11 ROUTINE MAINTENANCE 6 Put the drum unit assembly in the printer. Figure 5-20 7 Reset the drum counter.
See the instructions supplied with the new drum unit. Make sure that the Drum LED is red. Caution ■ The Drum LED indication does not disappear until you reset the drum counter. ■ Do not reset the drum counter when you replace only the toner cartridge. 8 Close the front cover. 9 Make sure that the printer is turned on, the front cover is open and the Status LED is now off. 5 - 11 ROUTINE MAINTENANCE 6 Put the drum unit assembly in the printer. Figure 5-20 7 Reset the drum counter.
Service Manual
Page 67
...When the Status LED comes on APIPA, see the Network User's Guide or visit http://solutions.brother.com 2-36 The print server has been reset to 4 above, however, hold down until all the LEDs light up again, the printer will start warming up . Link/Speed LED is orange: Fast Ethernet Link/Speed LED is...except for Toner LED go off the printer. (2) Make sure that the front cover is closed and the power cord is connected to a 100BaseTX Fast Ethernet network. Keep the Go button pressed down until the yellow Status LED comes on the power switch. When the Drum, Paper and Status LEDs go off...
...When the Status LED comes on APIPA, see the Network User's Guide or visit http://solutions.brother.com 2-36 The print server has been reset to 4 above, however, hold down until all the LEDs light up again, the printer will start warming up . Link/Speed LED is orange: Fast Ethernet Link/Speed LED is...except for Toner LED go off the printer. (2) Make sure that the front cover is closed and the power cord is connected to a 100BaseTX Fast Ethernet network. Keep the Go button pressed down until the yellow Status LED comes on the power switch. When the Drum, Paper and Status LEDs go off...
Service Manual
Page 165
... toner powder does not spill out of the drum unit assembly. (Fig.5-4) HL-5030/5040/5050/5070N SERVICE MANUAL (4) Unpack the new drum unit. (5) Put the toner cartridge in the new drum unit until you reset the drum counter. • It is now off with the new drum unit. (8) Close the front cover. (9)... Make sure that the Drum LED is recommended to install it separate from the drum unit when you pick up the drum unit tightly so that the printer is lifted...
... toner powder does not spill out of the drum unit assembly. (Fig.5-4) HL-5030/5040/5050/5070N SERVICE MANUAL (4) Unpack the new drum unit. (5) Put the toner cartridge in the new drum unit until you reset the drum counter. • It is now off with the new drum unit. (8) Close the front cover. (9)... Make sure that the Drum LED is recommended to install it separate from the drum unit when you pick up the drum unit tightly so that the printer is lifted...
Service Manual
Page 183
... the corona wire. (Refer to reset the printer with a new one. Type of error Toner empty Cover open (Front cover) Cover open (Jam clear cover) Paper jam No paper (HL-5030) No paper (HL5040/5050/5070N) No tray 1 Manual feed Memory full Print overrun Clean drum unit Toner (Yellow light) LED Drum (Yellow light) Paper (Yellow...
... the corona wire. (Refer to reset the printer with a new one. Type of error Toner empty Cover open (Front cover) Cover open (Jam clear cover) Paper jam No paper (HL-5030) No paper (HL5040/5050/5070N) No tray 1 Manual feed Memory full Print overrun Clean drum unit Toner (Yellow light) LED Drum (Yellow light) Paper (Yellow...
Service Manual
Page 235
...Drum Paper Status (yellow) Status (green) Type of the internal fonts. model, it as shown in the table below ; (1) Turn off the power switch of Chapter 2. 7-1 Press the Go button until the Toner LED comes on . The printer returns to its factory setting. (APIPA is restored to Section 6.2 of the printer...to the ready status after printing. The printer is ON) Refer to use following the steps below . The printer returns to execute the test print, release and then press the Go button again when the Toner LED comes on . HL-5030/5040/5050/5070N SERVICE MANUAL CHAPTER 7 ...
...Drum Paper Status (yellow) Status (green) Type of the internal fonts. model, it as shown in the table below ; (1) Turn off the power switch of Chapter 2. 7-1 Press the Go button until the Toner LED comes on . The printer returns to its factory setting. (APIPA is restored to Section 6.2 of the printer...to the ready status after printing. The printer is ON) Refer to use following the steps below . The printer returns to execute the test print, release and then press the Go button again when the Toner LED comes on . HL-5030/5040/5050/5070N SERVICE MANUAL CHAPTER 7 ...