Users Manual - English
Page 109
See the instructions supplied with the new drum unit. Caution ■ The Drum LED indication does not disappear until you reset the drum counter. ■ Do not reset the drum counter when you replace only the toner cartridge. 8 Close the front cover. 9 Make sure that the printer is turned on, the front cover is open and the Status LED is now off. 5 - 11 ROUTINE MAINTENANCE 6 Put the drum unit assembly in the printer. Figure 5-20 7 Reset the drum counter. Make sure that the Drum LED is red.
See the instructions supplied with the new drum unit. Caution ■ The Drum LED indication does not disappear until you reset the drum counter. ■ Do not reset the drum counter when you replace only the toner cartridge. 8 Close the front cover. 9 Make sure that the printer is turned on, the front cover is open and the Status LED is now off. 5 - 11 ROUTINE MAINTENANCE 6 Put the drum unit assembly in the printer. Figure 5-20 7 Reset the drum counter. Make sure that the Drum LED is red.
Service Manual
Page 67
... (For HL-5070N) If you wish to reset the print server back to reset the printer and automatically disable the APIPA protocol, follow these steps; (1) Turn off the printer. (2) Make...visit http://solutions.brother.com 2-36 CHAPTER 2 INSTALLATION AND BASIC OPERATION 6. Keep the Go button pressed down until all the LEDs light up again, the printer will be green... if the print server is green, not yellow. *For more information on the power switch. Link/Speed LED is orange: Fast Ethernet Link/Speed LED is not connected to a 10 Base T Ethernet. When the Drum...
... (For HL-5070N) If you wish to reset the print server back to reset the printer and automatically disable the APIPA protocol, follow these steps; (1) Turn off the printer. (2) Make...visit http://solutions.brother.com 2-36 CHAPTER 2 INSTALLATION AND BASIC OPERATION 6. Keep the Go button pressed down until all the LEDs light up again, the printer will be green... if the print server is green, not yellow. *For more information on the power switch. Link/Speed LED is orange: Fast Ethernet Link/Speed LED is not connected to a 10 Base T Ethernet. When the Drum...
Service Manual
Page 165
... toner powder does not spill out of the drum unit assembly. (Fig.5-4) HL-5030/5040/5050/5070N SERVICE MANUAL (4) Unpack the new drum unit. (5) Put the toner cartridge in the new drum unit until you reset the drum counter. • It is recommended to clean the printer when you pick up the drum unit assembly. CAUTION: • Only unpack...
... toner powder does not spill out of the drum unit assembly. (Fig.5-4) HL-5030/5040/5050/5070N SERVICE MANUAL (4) Unpack the new drum unit. (5) Put the toner cartridge in the new drum unit until you reset the drum counter. • It is recommended to clean the printer when you pick up the drum unit assembly. CAUTION: • Only unpack...
Service Manual
Page 183
... (HL-5030) No paper (HL5040/5050/5070N) No tray 1 Manual feed Memory full Print overrun Clean drum unit Toner (Yellow light) LED Drum (Yellow light) Paper (Yellow blink) Status (Red light)) Remedy Replace the toner cartridge with the control panel button. Load paper into the printer. ... 3 of Chapter 5.) 6-4 Clear the jammed paper inside the printer. Press the go button. (Error message is displayed. (Except for each indication to reset the printer with a new one. Press the panel button if the printer does not automatically resume printing. Type of the fuser unit. ...
... (HL-5030) No paper (HL5040/5050/5070N) No tray 1 Manual feed Memory full Print overrun Clean drum unit Toner (Yellow light) LED Drum (Yellow light) Paper (Yellow blink) Status (Red light)) Remedy Replace the toner cartridge with the control panel button. Load paper into the printer. ... 3 of Chapter 5.) 6-4 Clear the jammed paper inside the printer. Press the go button. (Error message is displayed. (Except for each indication to reset the printer with a new one. Press the panel button if the printer does not automatically resume printing. Type of the fuser unit. ...
Service Manual
Page 235
...button again when the Toner LED comes on . Select the test mode you want to Section 6.2 of Chapter 2. 7-1 The network setting is reset to its factory setting. (APIPA is ON) Refer to use following the steps below . Release and then press the Go button to the ...power switch of Chapter 2. The printer returns to the ready status after printing. LED Toner Drum Paper Status (yellow) Status (green) Type of the internal fonts. Press the Go button until the Toner LED comes on . The printer returns to the ready status after printing. HL-5030/5040/5050/5070N SERVICE MANUAL CHAPTER...
...button again when the Toner LED comes on . Select the test mode you want to Section 6.2 of Chapter 2. 7-1 The network setting is reset to its factory setting. (APIPA is ON) Refer to use following the steps below . Release and then press the Go button to the ...power switch of Chapter 2. The printer returns to the ready status after printing. LED Toner Drum Paper Status (yellow) Status (green) Type of the internal fonts. Press the Go button until the Toner LED comes on . The printer returns to the ready status after printing. HL-5030/5040/5050/5070N SERVICE MANUAL CHAPTER...