BenQ RP653 Support and Manuals
Get Help and Manuals for this BenQ item
BenQ RP653 Videos
[Case Study] BenQ RP653 Interactive Flat Panel at Delhi Private School Dubai
Duration: 3:31
Total Views: 1,146
Duration: 3:31
Total Views: 1,146
BenQ rp653
Duration: 2:26
Total Views: 284
Duration: 2:26
Total Views: 284
????????????? ??-?????? BenQ RP653
Duration: 6:35
Total Views: 6,214
Duration: 6:35
Total Views: 6,214
Popular BenQ RP653 Manual Pages
RS232 command - Page 12
...enable or not. Byte1[5]=1 means enable.
Network Setting 14
Input Value: Byte1 - Byte3...Byte9 (1) Byte1=0x00: IP Setup Mode
Byte1=0x01: IP Address Byte1=0x02: ...return value should be
g E1
Byte1=0x00
Byte1=0x00
Byte2=0x00: Manual
Byte2=0x00: Manual
0x01: DHCP
0x01: DHCP
Byte3~9 are reserverd, should be 0x00....Cmd Code
RS232
14
g E0 Input value: Byte1 - Byte1[4]: The Off Timer ...
Installation Handbook - Page 29
...DVI or Composite before making the daisy chain.
Video wall installation guide 29 Page 36
Use an appropriate RS-232C cable.
Function...manual or BenQ service for all displays by RS-232 commands
D-Sub, Composite, and DVI support daisy chaining.
Different types of daisy chain
Depending on your product, you can purchase them separately. Check the specifications of the purchased model...
Installation Handbook - Page 35
...not supplied). 2.
The centralized management could be done by remote control (selected models only)
1. Refer to the user manual of the first display. 3. Refer to Notes on using the remote control on... numbers have been set, you are ready to control all displays centrally. Video wall installation guide 35 IR cable
30° 30°
8M
• RS232 daisy chain only supports up to 98....
Installation Handbook - Page 36
...
1. See Setting the ID number of each
display: PL460/PH460/PL550/PH550 on page 34 for more information. 2. Refer to the user manual or BenQ service for more ...set .
Connect all displays separately to a LAN switch or hub using the RS-232C serial null modem cables (purchased separately if
not supplied). 4. Make sure the network connection is enabled.
36 Video wall installation guide...
Installation Handbook - Page 38
...BenQ customer service center for each display easily on a host computer.
Go to General settings > LED and set it to General settings > Monitor ID and set different ID for demonstration videos if needed .
38 Video wall installation guide...user manual or BenQ service for demonstration videos if needed . Refer to the user manual or BenQ service for the software and the user manuals. ...
Installation Handbook - Page 65
... is observed or noise is used for details.
Restore the display to the
properly. The main board could be
Contact the BenQ authorized service partner for
damaged.
Check the cable connection. Press any of the displayed is not
Make sure the power switch is D-Sub (VGA).
replacement.
Poor quality cable is heard.
Troubleshooting 65
Installation Handbook - Page 67
.... On your operating system for more information. For advanced setting, change the setting under H. In H. to the left. Troubleshooting 67 to move the picture to move the picture up; What are the supported resolutions of PIP function also depends on the remote control to make adjustment manually. The picture unstable, unfocused, or swimming. • Make...
Installation Handbook - Page 68
...Contact the BenQ authorized service partner for
damaged. Audio
The image is displayed but no sound is the
consistent with a new battery.
Update the driver through Windows Update (for Windows Operating Systems) or the graphic card's manufacturer. same with a new remote control.
HDMI.
Refer to the display and adjust the
connected.
Replace with the display setting.
Installation Handbook - Page 69
...specifications. Possible causes
An inappropriate stylus (particularly too thin) is covered by your display only;
Check the user manual for the supported operating systems. Visit the BenQ...installed.
Refer to clean the touch screen. To avoid damage to the screen, never use any extension (e.g. Touch function (selected models...
2. Troubleshooting 69 The touch driver is ...
Installation Handbook - Page 71
... setting
Troubleshooting 71
Possible causes
Possible solutions
The control panel (keypad) could be enabled at the same time. replacement.
Please check the following to unlock it. OSD setting
Press red
1. The Key Lock and
button on remote
control.
RP552, RP552H, RP653, RP703, RP840G
OSD setting
OSD setting
Press red button on the remote control.
RP553K, RP653K...
Installation Handbook - Page 74
... the supported resolutions of normal operation. Go to Setting > Information > Software Version to adjust the system clock. This condensation will usually disappear after around 2 hours of my display? Vapor or mist is not supported. Press the control panel buttons to find out the software version.
74 Troubleshooting Go to the user manual for the supported timings...
Installation Handbook - Page 78
...set the PC or system to run a screen saver when not in use. A previous image can cause the liquid crystals to user manuals... in case you leave the screen fixed on the instruction guide. Warranty service may be restricted relying on a stationary image for... saver is not operating normally, afterimage burn-in may vary by models. Power saving mode
• After using the product for 12 ...
Installation Handbook - Page 79
...screen is normal.
Before installation
No. scratched or cracked). 10. Appendix 1: Installation Checklists 79 Contact the BenQ local customer service center with the checking ...problem
1. Check if the panel is damaged (i.e. scratches, cracks,
bends) to the edges and surface area.
5. The Installation Handbook has been read through carefully.
2. • For certain models...
Installation Handbook - Page 85
...or use extender if longer than 5m.
Contact the service provider for IFP & IL 85
If the touch is not working only..., please connect to the external device to un-install the Smart Notebook software (if provided), and install an earlier version. computer) and your display. ...
problem still exist?
Yes No
Appendix 2: Basic Troubleshooting Checklists for an earlier version if needed.
Installation Handbook - Page 87
... the service provider to see if a calibration software is not working, please add a USB hub/extender.
Check if completed
Does the problem still
exist? Add extender/repeater
Check if completed
Does the problem still
exist? Yes No
Appendix 2: Basic Troubleshooting Checklists for hours. Condensation may last for IFP & IL 87 If there is supported by...
BenQ RP653 Reviews
We have not received any reviews for BenQ yet.