V2-M2NC61S User's Manual for English Edtion
Page 1
U2811 V-Series M2NC61S ASUS PC (Desktop Barebone) Installation Manual
U2811 V-Series M2NC61S ASUS PC (Desktop Barebone) Installation Manual
V2-M2NC61S User's Manual for English Edtion
Page 2
... Parallel port USB 2.0 ports Center/subwoofer port Microphone port Line Out port Line In port Expansion slot Metal brackets 3.5-inch drive bay cover Headphone port Microphone port USB 2.0 ports HDD LED Reset button Power button Power supply fan Cover screw Chassis fan vents VGA port IEEE 1394 port Side speak out port LAN (RJ-45) port Rear speak out port Cover screw Metal bracket lock Installation manual Refer to your product package for installation details and other system information from ASUS website. Front panel features 5.25-inch drive bay cover This V-series provide V2...
... Parallel port USB 2.0 ports Center/subwoofer port Microphone port Line Out port Line In port Expansion slot Metal brackets 3.5-inch drive bay cover Headphone port Microphone port USB 2.0 ports HDD LED Reset button Power button Power supply fan Cover screw Chassis fan vents VGA port IEEE 1394 port Side speak out port LAN (RJ-45) port Rear speak out port Cover screw Metal bracket lock Installation manual Refer to your product package for installation details and other system information from ASUS website. Front panel features 5.25-inch drive bay cover This V-series provide V2...
V2-M2NC61S User's Manual for English Edtion
Page 3
...‑127 V, set the switch to 115 V. If the voltage supply in your area is 200‑240 V, set the switch to 230 V. Hard disk drive bay 4. Power supply unit 6. CPU socket 7. ASUS motherboard 9. If the voltage supply in your area. eSATA Installation manual PCI slots 12. DIMM sockets 8. PCI Express x16 slot 10. Metal bracket lock Selecting the voltage The system's power supply unit has a 115 V/230 V voltage selector switch located beside the power connector.
...‑127 V, set the switch to 115 V. If the voltage supply in your area is 200‑240 V, set the switch to 230 V. Hard disk drive bay 4. Power supply unit 6. CPU socket 7. ASUS motherboard 9. If the voltage supply in your area. eSATA Installation manual PCI slots 12. DIMM sockets 8. PCI Express x16 slot 10. Metal bracket lock Selecting the voltage The system's power supply unit has a 115 V/230 V voltage selector switch located beside the power connector.
V2-M2NC61S User's Manual for English Edtion
Page 4
Removing the side cover and front panel assembly 1. Swing the front panel assembly to a 90º100º angel. 3 4 Installation manual Locate the CPU socket,then lift the socket lever to the right, until they disengage from the chassis tabs. Locate the front panel assembly hooks, then lift them until the hinge-like tabs on the rear panel. 2. Set the side cover aside. 3. Remove the cover screws...
Removing the side cover and front panel assembly 1. Swing the front panel assembly to a 90º100º angel. 3 4 Installation manual Locate the CPU socket,then lift the socket lever to the right, until they disengage from the chassis tabs. Locate the front panel assembly hooks, then lift them until the hinge-like tabs on the rear panel. 2. Set the side cover aside. 3. Remove the cover screws...
V2-M2NC61S User's Manual for English Edtion
Page 5
... retention bracket lock) to the module base. 5. When the fan and heatsink assembly is in place, connect the CPU fan cable to the retention module base. 3. 2. Align the other end of the retention bracket to the connector on top of the installed CPU, making sure that the retention bracket is in place. 4. Place the heatsink on the motherboard labeled CPU_FAN.
... retention bracket lock) to the module base. 5. When the fan and heatsink assembly is in place, connect the CPU fan cable to the retention module base. 3. 2. Align the other end of the retention bracket to the connector on top of the installed CPU, making sure that the retention bracket is in place. 4. Place the heatsink on the motherboard labeled CPU_FAN.
V2-M2NC61S User's Manual for English Edtion
Page 6
... the power supply before adding or removing DIMMs. Failure to do so may cause damage to the slot, then press the card firmly until it fits in only one direction. Replace the metal bracket lock. 3 4 Installation manual Installing a DIMM 1. Unlock a DIMM socket by pressing the retaining clips outward. 3. Do not force a DIMM into a socket to use. 2 1 3. Remove the metal cover opposite the slot that you...
... the power supply before adding or removing DIMMs. Failure to do so may cause damage to the slot, then press the card firmly until it fits in only one direction. Replace the metal bracket lock. 3 4 Installation manual Installing a DIMM 1. Unlock a DIMM socket by pressing the retaining clips outward. 3. Do not force a DIMM into a socket to use. 2 1 3. Remove the metal cover opposite the slot that you...
V2-M2NC61S User's Manual for English Edtion
Page 7
... of the bay. 4. Place the chassis upright, then remove the upper 3.5" drive bay metal plate cover. 2. Installing storage drives Optical drive 1. Secure the floppy disk drive with the holes on the bay. 3. Hard disk drive 1. Connect the IDE (A) and power (B) plugs to connectors at the back of the drive. Connect the signal (A) and power (B) plugs to connectors at the back of the drive. Insert the optical drive to the bay, then carefully push the...
... of the bay. 4. Place the chassis upright, then remove the upper 3.5" drive bay metal plate cover. 2. Installing storage drives Optical drive 1. Secure the floppy disk drive with the holes on the bay. 3. Hard disk drive 1. Connect the IDE (A) and power (B) plugs to connectors at the back of the drive. Connect the signal (A) and power (B) plugs to connectors at the back of the drive. Insert the optical drive to the bay, then carefully push the...
V2-M2NC61S User's Manual for English Edtion
Page 8
... cover to the chassis. Secure the cover with two screws you installed an optical and/or floppy disk drive, remove the bay cover(s) on the right side of the front panel until the front panel assembly fits in place. 5. For SATA HDD: Connect the SATA signal and power plugs to the chassis until it aside. 4. To do this: 1. Locate the bay cover locks. 2. Push the bay cover inward, then set...
... cover to the chassis. Secure the cover with two screws you installed an optical and/or floppy disk drive, remove the bay cover(s) on the right side of the front panel until the front panel assembly fits in place. 5. For SATA HDD: Connect the SATA signal and power plugs to the chassis until it aside. 4. To do this: 1. Locate the bay cover locks. 2. Push the bay cover inward, then set...