Asus P2B MB Support and Manuals
Get Help and Manuals for this Asus item
Popular Asus P2B MB Manual Pages
P2B User Manual - Page 4
HARDWARE SETUP 10
Layout of the ASUS P2B Motherboard 8 The ASUS P2B Motherboard 9
III. INTRODUCTION 7
How this Manual is Organized 7 Item Checklist 7
II. CONTENTS
I. FEATURES 8
Features of the ASUS P2B Motherboard 10 Installation Steps 12 Jumpers 12
Jumper Settings 13 System Memory (DIMM 17
SPD Support 17 DIMM Memory Installation Procedures 18 Central Processing Unit (CPU 19 ...
P2B User Manual - Page 7
...) ASUS PCI-L101 Wake-on the included support software
VI. INTRODUCTION Manual / Checklist
I . Hardware Setup: Instructions on setting up the motherboard
IV. INTRODUCTION
How this product
III. BIOS Setup:
Instructions on setting up the BIOS software
V. Introduction: Manual information and checklist
II. I . Features:
Information and specifications concerning this Manual...
P2B User Manual - Page 13
... on the +5VSB lead and the new ACPI BIOS support. Set to Disable because not all computers have the right ATX power supply. This feature requires an ATX power supply that can supply at least 300mA on your computer. H/W SETUP Jumpers
ASUS P2B User's Manual
13 HARDWARE SETUP
Jumper Settings
1. Keyboard Power Up (KBPWR) This allows you...
P2B User Manual - Page 15
... processor as follows:
Intel CPU Model Pentium III Pentium III
Freq.
HARDWARE SETUP
Set the jumpers by the Internal speed of your processor is not needed for the Pentium III/ II/Celeron processor because it sends a VID signal directly to the onboard power controller. H/W SETUP Jumpers
ASUS P2B User's Manual
15 It may result in a slower...
P2B User Manual - Page 17
...Setup" in BIOS SETUP. SPD Support
This motherboard supports SPD DIMMs, and it is recommended through Chipset Features Setup in any combination as registered memory.
ASUS P2B User's Manual
17 H/W SETUP System Memory
III. Sockets are not PC100-compliant, set... shows SDRAM memory on the motherboard. III. Install memory in BIOS SETUP. stability. • SDRAM chips are only available...
P2B User Manual - Page 24
...will be used , leaving 5 IRQs free.
Replace the computer system's cover. 6. The original ...SETUP) 7. Remove your used by a particular device (to use at the same time.
24
ASUS P2B User's Manual Secure the card on the slot you removed above. 5. Assigning IRQs for possible future use IRQs. Install the necessary software drivers for your motherboard and expansion cards. Set...
P2B User Manual - Page 28
...pin plug.
28
ASUS P2B User's Manual After connecting the ...supports SCSI device or IDE CD-ROM bootup (see "HDD Sequence SCSI/IDE First" & "Boot Sequence" in the BIOS Features Setup of your hard disk(s). TIP: You may install...SETUP
6. H/W SETUP Connectors
Universal Serial Bus (USB) 2
7. If you install... Setup. Primary / Secondary IDE Connectors (Two 40-1pin IDE) These connectors support ...
P2B User Manual - Page 37
... particular, the hard disk specifications. BIOS Updating BIOS
ASUS P2B User's Manual
37
But do so only if the first two methods fail.
If your system using this utility. Press to run this section. If you are released. Use the Flash Memory Writer utility to call up Setup. If so, invoke the Setup utility, as described...
P2B User Manual - Page 40
... support this field to each field: Primary Master, Primary Slave, Secondary Master, and Secondary Slave, you are EGA/VGA, CGA 40, CGA 80, and MONO (for a particular drive, highlight its partition set to change your IDE hard disk during bootup.
BIOS Standard CMOS
40
ASUS P2B User's Manual If you may choose from All Errors...
P2B User Manual - Page 43
...using OS/2 operating systems with ROMs on them specifically. Video ROM BIOS Shadow (Enabled) This ...install other settings are available: 250, 500, 750, and 1000. BIOS BIOS Features
ASUS P2B User's Manual
43
IRQ12 will be reserved for expansion cards if a PS/2 mouse is detected or not. Otherwise leave this problem.
Setup default setting is 6; other expansion cards with installed...
P2B User Manual - Page 45
... the floppy disk drives, set this field to ISA expansion cards that specifically require this field allows you to the system.
This makes the memory from 15MB and up to the onboard floppy disk drive connector instead of the processor.
IV. BIOS Chipset Features
ASUS P2B User's Manual
45 PCI 2.1 Support (Enabled) This function allows...
P2B User Manual - Page 50
... that IRQ.
Two options are manual settings of using an ICU, you must set how IRQ use is Auto, which uses auto-routing to determine IRQ use INTA#, thus all installed PCI cards must be reassigned by...next to Yes...
50
ASUS P2B User's Manual PCI Latency Timer (32 PCI Clock) The default setting of No. All PCI bus slots on the system use . The default setting for each field is ...
P2B User Manual - Page 53
... alphanumeric characters long, type in the Jumper Settings section. ASUS P2B User's Manual
53 If you want to the main screen. A message confirms the password has been disabled.
BIOS Passwords
To implement password protection, specify in the "Security Option" field of entering a new password when the "Enter Password" prompt appears. A password prompt appears on the system. IV.
P2B User Manual - Page 54
... you must support the Enhanced IDE features in the Standard CMOS Setup screen. The auto-detection feature can use Drive E and Drive F. Pressing to skip rather than one set of parameters causes...not a problem if the drive is completed, the program automatically enters all entries you are not entered in this case); When auto-detection is new and empty.
54
ASUS P2B User's Manual
IV....
P2B User Manual - Page 55
...ASUS P2B User's Manual
55 If the parameters listed differ from the Standard CMOS Setup screen. If the auto-detected parameters do not match the ones that should be readable. Press to exit the Setup...screen, type "Y", and then press . Save & Exit Setup
Select this option to reject the presented settings and enter the correct ones manually from the ones used for your hard disk was formatted...
Asus P2B MB Reviews
We have not received any reviews for Asus yet.