3Com 3CRWE915075 - AirConnect 9150 11n 2.4 GHz PoE Access Point Support and Manuals
Get Help and Manuals for this 3Com item
View All Support Options Below
Free 3Com 3CRWE915075 manuals!
Problems with 3Com 3CRWE915075?
Ask a Question
Free 3Com 3CRWE915075 manuals!
Problems with 3Com 3CRWE915075?
Ask a Question
Popular 3Com 3CRWE915075 Manual Pages
User Guide - Page 7
Profile (SSID) Isolation 36 WDS Link Settings 36 WDS Security Settings 38 Wireless Advanced Settings 39
Transmit Power 39 Beacon Interval 40 Data Beacon Rate 40 Association Timeout 40 Fragment Length 40 RTS/CTS Threshold 40 802.11d support 41 Distance 41 Antenna Type 41 Aggregation Support 41 QoS 42 Service 43 Management VLAN 43 IAPP 44...
User Guide - Page 8
Syslog Function 50 System Log 50 Syslog Server 51 Syslog Port 51 Syslog Level 51
Management 52 Administration 52 SNMP 53 MAC Filtering 54 Rogue AP Detection 55 Backup/ Restore Settings 56 Firmware Auto Upgrade 57 Firmware Manual Upgrade 58 Rebooting 60
Connecting Through the Com Port 61 Restoring Factory Settings 62
TROUBLESHOOTING
Diagnosing Problems 63
User Guide - Page 11
... sensitive data broadcast over the wireless LAN, 3Com supports Wireless Equivalent Privacy (WEP) and Wi-Fi...3Com AirConnect 9150 11n 2.4GHz PoE Access Point are high performance access points that allow you to 64 simultaneous users. Security
3Com offers one of the most robust suites of security for network data and communications. This AP creates an enterprise-class wireless LAN, supporting...
User Guide - Page 16
12
Key Product Features
Installing Your 3com Wireless Access Point
To set up and install your 3Com Wireless Access Point, please refer to the 3Com® AirConnect® 9550 11n 2.4+5GHz PoE Access Point 3CRWE955075 / WL-605 3Com® AirConnect® 9150 11n 2.4GHz PoE Access Point 3CRWE915075 / WL-604 Quick Start Guide (Part Number 10016854).
User Guide - Page 27
...; Wireless Mode - Choose a channel from the drop down menu or select SmartSelect (recommended) to set up the AP. To start the Setup Wizard, click Setup Wizard.
1 Figure 8 allows you through setting up the following information: ■ SSID (Service Set Identifier) - Setup Wizard
The Setup Wizard will learn how to configure the basic functions of wireless network. Choose the...
User Guide - Page 41
System Configuration
37
Figure 17 WDS Link Settings
Supports up to 8 point to . Example of any other APs you want to link to multipoint WDS links. Check Enable WDS and then Enable on the MAC addresses want to link to. Enter the MAC addresses of a WDS topology: AP1 Master AP (our AP) AP3 AP4
User Guide - Page 45
.... System Configuration
41
802.11d support
802.1d allows the device to replace the original internal antennas), check ...3com 6/8dBi Dual-Band Omni Antenna ■ 3CWE596 3com 18/20dBi Dual-Band Panel Antenna ■ 3CWE598 3com 8/10dBi Dual-Band Panel Antenna
Aggregation Support
Sets the aggregation type: ■ A-MPDU : Aggregate MAC protocol data unit. ■ A-MSDU : Aggregate MAC service...
User Guide - Page 47
Service
43
Service
Management VLAN
If you reconfigure the Management VLAN ID, you may lose connectivity to the new IP address. Figure 20 Management VLAN Verify that the switch and DHCP server can support the reconfigured VLAN ID, and then re-connect to the access point.
User Guide - Page 48
44
Service
IAPP
Inter-Access Point Protocol (IAPP)
Figure 21 IAPP
802.11F (IAPP) Support
Choose either Enable or Disable IAPP allows multiple access points to communicate and pass location information about their associated stations. If you enable 802.11F support you should manually add BSSID/IP mapping: 1 Enter the BSSID and IP addresses of the AP.
User Guide - Page 51
However, access points do not support the admission control procedure in this release, clients are blocked from ...that access category. default : disable
The default value table:
AC TYPE
AC_BK AC_BE AC_VI
Min Contention Window (2x-1; Service
47
Setting
Admission Control
Description
Note: In this release, so clients cannot use the access category when you enable admission control ...
User Guide - Page 53
...Service
49
The following settings can be input manually, to avoid any regional policy changes. SNTP client enable/disable
Set Time Timezone selection
Daylight Saving
Primary and Secondary SNTP server/port setting
... time from the Primary server first. These fields are considered to input time manually.
This selection adjusts the time obtained from configured SNTP servers. The start/end...
User Guide - Page 66
... Access Point can be reset to the default factory settings either through the web browser (see "Backup/ Restore Settings" on the side of the Access Point, and hold for five seconds. Figure 34 Reset Hole Location
Reset Hole
To restore the settings manually, insert a pointed object (such as the end of a straightened paper clip...
User Guide - Page 69
... its IP address from a DHCP server, the Access Point is unable to associate with the network. Diagnosing Problems
65
4 Make sure the subnet address matches that the Wireless LAN Service Area, channel selections, Data Preamble setting, and security setting are running Windows NT. Symptom
Two Access Points cannot communicate in ad-hoc mode, the...
User Guide - Page 71
Some problems can be solved by installing a new version of the firmware. Solution
Firmware is the software that is installed on how to confirm, click OK. When prompted to download a firmware update from the 3Com customer support Web site and install it on your Access Point, see "Firmware Auto Upgrade" on page 57 or "Firmware Manual Upgrade" on page 58. Symptom
Upgrading Access Point Firmware....
User Guide - Page 72
... FOR YOUR 3COM PRODUCT
Telephone Technical Support and Repair
To obtain telephone support as part of your warranty and other service benefits, you must first obtain a return materials authorization number (RMA). Products sent to 3Com without authorization numbers clearly marked on the outside of system hardware and software, including revision
level ■ Diagnostic error messages ■...
3Com 3CRWE915075 Reviews
We have not received any reviews for 3Com yet.