Zenith SL-6026-WH-A Support Question
Zenith SL-6026-WH-A Support Question
Find answers below for this question about Zenith SL-6026-WH-A - Heath - Wireless Command Motion Activated Lamp Socket Control.Need a Zenith SL-6026-WH-A manual? We have 1 online manual for this item!
Question posted by gablanchard1 on December 31st, 2010
One Light On During The Day, Reluctant To Light At Night.
I have two driveway lights setup to run at night only. One of them is slow (if at all) to light at night but wants to stay lit all day.
Help!
Current Answers
Related Zenith SL-6026-WH-A Manual Pages
User Guide - Page 1
...controlled products. Note: The code can also be changed to 100 feet.
Lamp Socket Converter
- Floodlight
- Switch 4 sets the Group (A or B). Code Settings, System 2 Note: When operating more than one system independently of examples 1 and 2
because the code setting is different. Transmitter(s)/ Receiver(s) Code
Transmitter(s)/ Receiver(s) Code
Receiver(s) Code
Remote Motion Sensor...
User Guide - Page 2
...Cover
Remote Control
CODE ...DAY NIGHT 1 2 3 4 NIGHT ONLY
5 1 TEST MIN
MAX
Indoor Wireless Motion Sensor
Screw Cover
Code Switches Lamp Socket Converter
1234
Code Switches
DAY NIGHT NIGHT ONLY
1234 CODES
DETECT
Outdoor Wireless Motion Sensor
Code Switches
Floodlight
ON
1 2 3 4
Code
Switches
Indoor Plug-In Converter ON
1 2 3 4 Note: The "X" has been placed on the switches to help...
User Guide - Page 3
.... Flat-Head Screwdriver
Optional Visor Clip
2
1
2
3
Removing Visor Clip -
Note: If light does not turn on or intermittently turns on rear of remote unit until it again to allow ... match (see Troubleshooting Guide. ENGLISH
REMOTE CONTROL
Note: One remote control is able to the same code as this remote control.
• DIM: Activates the DIM feature for added convenience that may...
User Guide - Page 4
...
transmitter. Remove transmitter and drill two 3/16" holes. Verify that receiver has been properly installed. The light should turn off when transmitter buttons are pushed, see illustration).
Access Door
Add-A-Switch
5. Continue to press... last DIM setting, push and release the DIM button. The light should be used .
Important: Wait 1 to 50% in
socket plus (+) side up .
User Guide - Page 5
... on transmitter flashes momentarily and receiver turns light off. Mount Transmitter.
Note: If transmitter does not operate correctly, see illustration). CR2032 3 VOLTS CR2032 3 VOLTS
Tape Mounting: Apply large piece of door or window in socket plus (+) side up . of Movement
Transmitter Mounted On Stationary Surface
Battery Replacement The entry transmitter requires...
User Guide - Page 6
.... • Insert the tabs on the ball mounting bracket into mounting bracket socket
6
598-1116-09
Replace battery compartment cover by sliding the cover down. • For indoor motion sensor, install batteries after sensor is designed to mount to Indoor Motion Sensor (Vertical Installation Shown)
DAY NIGHT NIGHT ONLY
1234 CODES
DETECT
CODE ON
DETECT
ON-TIME RANGE (MINUTES...
User Guide - Page 7
... of LED light). 2. Set the ON-TIME control to a sturdy object (i.e. Tighten clamp screw. Place indoor motion sensor against surface to change the coverage area. Using a 2.5 mm (0.1") drill bit, drill two pilot holes for the
coverage desired. Using a Philips-head screwdriver, loosen the clamp screw on the motion sensor: • Indoor Motion Sensor - Mounting Bracket Socket
Clamp Screw...
User Guide - Page 8
... Motion Sensor Coverage
8
598-1116-09 Set the DETECT control switch to stay on after motion is detected (1 or 5 minutes). Note: If the RANGE is most sensitive to the corresponding setting. Slide the ON-TIME control to motion across its field of time you want the connected device to DAY/NIGHT and B. Do not point other lights at the sensor. Outdoor Motion Sensor...
User Guide - Page 9
... Volume Control
LAMP SOCKET CONVERTER
Features and Ratings: • Up to select between AUTO and MANUAL modes. CAUTION: Do not exceed the maximum load limits listed above . 3.
Check operation. Using Remote By-Pass Switch. Some models are equipped with a remote by remote control or remote motion sensor. Screw incandescent bulb up to rated wattage
into light socket. 2. INDOOR...
User Guide - Page 10
... cover plate and cover plate gasket.
Secure with silicone weather sealant. 8.
Note: Do not rotate the lamp holders more than 180° from the light receiver through the hole in the center of the cover plate. Activate transmitter being used to turn the receiver ON or OFF. Thread the small end of the...
User Guide - Page 11
...match.
8. Same as 5, 6, and 7 above . 1. Short term power line failure.
2.
You may also want to visit our Web site at 1-800-858-8501, 7:30 AM to operate the equipment.
598-1116-09
...POSSIBLE CAUSE 1. If the problem persists, call 1-800-858-8501 for 90 second initialization period
(remote motion sensor). 5. Device does not turn off .
2. The user is out of range.
6. Wait for ...
User Guide - Page 12
..., WHETHER OR NOT FORESEEABLE. You may not apply to misuse, abuse or negligence, light bulbs, batteries, and other equipment and components that a customer uses in conjunction with ...our products. TWO YEAR LIMITED WARRANTY
This is required for inconvenience, installation, setup time, loss of use, unauthorized service, or return shipping charges. Proof of purchase is...
Similar Questions
How To Deactivate The Motion Sensor On The Heath/zenith Sl-5610-wh-b?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
(Posted by emvilla 4 years ago)
Zenith Hologen Motion Sensor Light
How do I adjust it so that both lights come on with motion and not just one>
How do I adjust it so that both lights come on with motion and not just one>
(Posted by drwoggon 9 years ago)
Motion Sensor Light Won't Turn Off
(Posted by ungm3lm4 9 years ago)
Heath Zenith Motion Sensor Light Wont Turn Off
(Posted by Tiighchairu 10 years ago)
