Zenith SL-4132-MW Support Question
Zenith SL-4132-MW Support Question
Find answers below for this question about Zenith SL-4132-MW - Heath - Bayside Mission Style 150-Degree Motion Sensing Decorative Security Light.Need a Zenith SL-4132-MW manual? We have 1 online manual for this item!
Question posted by kjcook on October 31st, 2010
Stay On
How do i get my light to stay out all night?
Current Answers
Related Zenith SL-4132-MW Manual Pages
User Guide - Page 1
... fixture below.
MODE.
MANUAL MODE
Manual mode only works at dawn.
Motion Sensing Coach Lights
Requirements
• The light control requires 120 volts AC. • If you want to AUTO....Works: Day
5 Seconds
x
1, 5, or 10 Min
To Dawn*
Night x x x
* resets to Auto Mode at night because daylight returns the sensor to use Manual Mode, the control
must be wired through a switch...
User Guide - Page 2
... up with a universal mounting bracket. However, if the slots on the fixture to junction box.
WARNING: Turn power off at 1, 5,
or 10 minutes
AUTO
Flip light switch
MANUAL MODE
off for one minute, then back on *
* If you get confused while switching modes, turn the power off for additional information). 3.
Note...
User Guide - Page 3
... attach the mounting plate to the junction box as shown below . If you may not need the green "pigtail".
Secure the other lights from the motion sensor. Twist the wires together and secure with a wire connector.
Secure with wire connectors. CAUTION: DO NOT connect the RED wire unless you want to allow the wires on the...
User Guide - Page 4
... light fixture: Strip the motion sensor's red wire and connect to control another motion sensing light fixture (Master / Slave): Strip the red wire in the fixture. It is recommended that either fixture will turn on the lamp in both motion sensing fixtures and void your warranty.
595-5530-13 For instance, if you have 3 fixtures rated 100 Watts, 150...
User Guide - Page 5
... installing the optional tail assembly, install the decorative nut onto the bottom of the fixture now. Bottom trim piece has drain hole
2. Install decorative nut.
595-5530-13
COMPLETE THE ... nuts.
Junction Box
❒ Caulk fixture mounting surface with decorative screws.
❒ If you may install the decorative tail as shown below. See fixture markings for proper bulb ...
User Guide - Page 6
... you want the light to stay on after motion is less sensitive to change temperature rapidly, such as shown and turn on.
These heat sources could cause false triggering.
• Areas where pets or traffic may trigger the control.
• Nearby large, light-colored objects reflecting daylight may damage the sensor. Any other lights at :
•...
User Guide - Page 7
... Test. (Set control switch to cover
desired area.
Light control may be sensing small animals or automobile traffic (re-aim sensor).
2. POSSIBLE CAUSE
1. SPECIFICATIONS
Range Up to 150° Electrical Load. . . . . .
Light control is in products previously sold. The sensor is normal under these conditions).
595-5530-13
Light switch is loose or burned out. 3. Bulb is...
User Guide - Page 8
... or consequential damages, so the above limitation or exclusion may also write* to visit our Web site at no charge to misuse, abuse or negligence, light bulbs, batteries, and other expendable items are not covered by factory defective parts or workmanship will void this guide.
THIS WARRANTY IS EXPRESSLY IN LIEU...
Similar Questions
150 Degree Motion Sensing Post Light Sensor - Black
If my information is correct, you no longer make this item. Who does?
If my information is correct, you no longer make this item. Who does?
(Posted by applegrove2035 2 years ago)
How To Deactivate The Motion Sensor On The Heath/zenith Sl-5610-wh-b?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
(Posted by emvilla 4 years ago)
Motion Sensor
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
(Posted by Barry95996 9 years ago)
How To Wire Health Motion Sensor Sl-5410a
(Posted by ranyog 9 years ago)
Just Had The Zenith Sl 5798 Installed & The Motion Sensor Does Not Seem To Work
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
(Posted by Peyton 11 years ago)