Home » Yamaha » Audio Mixers » Yamaha EMX5000-20

Yamaha EMX5000-20 Support Question

Find answers below for this question about Yamaha EMX5000-20.
Need a Yamaha EMX5000-20 manual? We have 1 online manual for this item!

Yamaha Overview Questions Manuals Reviews Videos Research

Question posted by mansoorkhan913 on November 5th, 2016

Spare Part Required For Yamaha 2100

i need DM circuit board YAMAHA # 2820 (x3638).

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on November 5th, 2016 7:20 AM

This answer was accepted by the poster of the original question.

Odin

Member since:
April 10th, 2010

Points: 41,236,690

1,100
points

That is probably available from the manufacturer: use the contact information here--https://www.contacthelp.com/yamaha/customer-service. If not, get the part number and follow the applicable suggestions at this previous answer.

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Related Yamaha EMX5000-20 Manual Pages

Owner's Manual - Page 2

... corresponding sections of the EMX5000-20, EMX5000-12 owner's manual have been revised. The Owner's Manual Revisions E Thank you for connecting Speakon connectors. Reduce the output level at the ST OUT fader (K) below the level that is being excessively overloaded and may malfunction. Use only Neutrik NL4FC plugs for purchasing the Yamaha EMX5000-20/EMX5000-12 Powered Mixer. B- 1-

Owner's Manual - Page 3

...Level Diagram 6 EMX5000-20/EMX5000-12 CH INPUT A [-60~-16dB] [-34~+10dB] EMX5000-12:CH1-8 EMX5000-20:CH1-16 B CH INSERT I/O [0dB] EMX5000-12:CH1-8 EMX5000-20:CH1-16 +48V PHANTOM 8CH/SW EMX5000-12:[CH1-8] EMX5000-20:[CH1-8] [CH9-...4dB] R PEAK DR PEAK DR MONO OUT [+4dB] A POWER AMP IN [+4dB] B YAMAHA SPEAKER PROCESSING YSP YSP MAIN L AUX1 AUX1 MONO BRIDGE INV Signal Select MAIN R MONO AUX2...

Owner's Manual - Page 4

... Park, CA 90620 The above warning is located on different branch (circuit breaker or fuse) circuits or install AC line filter/s. WARNING: THIS APPARATUS MUST BE EARTHED ...apply ONLY to those products distributed by Yamaha may be connected to use this manual, meets FCC requirements. Modifications not expressly approved by Yamaha Corporation of uninsulated "dangerous voltage" within...

Owner's Manual - Page 5

...vacation, remove the power plug from the AC outlet, and remove all musical instruments, audio equipment, and speakers when connecting to this unit. Maintenance • Clean the contacts of... electrical shock. In particular, be damaged, turn the power switch off all connecting cables. EMX5000-20/EMX5000-12-Owner's Manual Failure to an AC outlet of the power cord. Locations exposed to...

Owner's Manual - Page 6

... noise into nearby radios and TVs. If noise occurs, use the telephone away from the unit. EMX5000-20/EMX5000-12-Owner's Manual Replacing abrasive parts • The performance of components with other electronic devices • The digital circuits of deterioration depends on cell phone usage • Using a cell phone (mobile telephone) near this unit...

Owner's Manual - Page 7

...EMX5000-20/EMX5000-12 and enjoy long, trouble-free performance, please read this owner's manual carefully, and keep it in energy cost and to less-restrictive installation requirements... limiter circuit to prevent distortion due to the acclaimed Yamaha SPX ...Yamaha EMX5000-20/EMX5000-12 Powered Mixer. This lets you switch the maximum output of the internal power amp as 16 (EMX5000-20), 8 (EMX5000...

Owner's Manual - Page 8

... left and right) in the SPEAKERS jack section on the rear panel of the EMX5000-20/EMX5000-12. EMX5000-20 (EMX5000-12) Setting the power ampliﬁer mode Set the power amp select switch ...; Be sure to use the SPEAKERS 1 jacks to the B jack in stereo. EMX5000-20/EMX5000-12-Owner's Manual EMX5000-20 (EMX5000-12) Power amp select switch • This quick guide explains how to connect one...

Owner's Manual - Page 9

... acoustic guitar or electric bass Connect electric/acoustic guitars or electric basses via an effect processor or direct box to the 2TR IN jacks. EMX5000-20 (EMX5000-12) Microphone EMX5000-20 (EMX5000-12) Using a condenser microphone Turn on the PHANTOM switch (located in the upper center corner on the panel). • The PHANTOM switch supplies phantom...

Owner's Manual - Page 10

... to the diagram below to make a stereo connection from the output jacks (such as a synthesizer, drum machine, signal processor connected to turn on the YAMAHA SPEAKER PROCESSING switch in stereo. EMX5000-20 (EMX5000-12) EMX5000-20 (EMX5000-12) Synthesizer, Drum machine, Guitar processor STEP 2 Power on 1 Turn on the power to all external devices connected to the...

Owner's Manual - Page 11

... EFFECT RTN fader to the "0" position. 3 EMX5000-20 (EMX5000-12) EMX5000-20 (EMX5000-12) STEP 4 Applying built-in the EFFECT section. The ON switch indicator lights up. 1 EMX5000-20 (EMX5000-12) 2 4 If you want to use the EMX5000-20/EMX5000-12, we recommend that you want to the "-∞" position. EMX5000-20/EMX5000-12-Owner's Manual EMX5000-20 (EMX5000-12) 4 STEP 5 Power off 1 Press...

Owner's Manual - Page 12

... are as follows: HIGH: 10kHz, ±15 dB, shelving type MID: 250Hz-5kHz, ±15 dB, peaking type LOW: 100Hz, ±15 dB, shelving type EMX5000-20/EMX5000-12-Owner's Manual Attenuation is on when the switch is pressed inward, and the frequency region below 80 Hz will have a ﬂat 18 dB...

Owner's Manual - Page 13

... on the input/output panel. When the switch is pressed inward, post-fader is near. EMX5000-20/EMX5000-12-Owner's Manual The signal of the EFFECT 1, 2 buses is sent to the built-...positioned at "w," at right at R, and at left at L. 8 BAL (balance) control (EMX5000-20: Channels 17/18-19/20, EMX5000-12: Channels 9/10-11/12) The BAL knobs set the stereo position of external equipment connected ...

Owner's Manual - Page 17

...YAMAHA SPEAKER PROCESSING \ ON/OFF switch This switch enables you specify by the control knob. Note: The setting of this when you to the signal that are using a sub-woofer. c LPF control, ON/OFF switch This switch applies a low-pass ﬁlter to monitor the level of the EMX5000-20/EMX5000... signal sent from the ST OUT jacks. EMX5000-20/EMX5000-12-Owner's Manual This will output the ...

Owner's Manual - Page 18

...channel 17/18-19/20 (EMX5000-20), 9/10-11/ 12 (EMX5000-12) input jacks if... the PHANTOM +48V switch (control panel 3) is switched on . 2 INSERT I /O jack Sleeve Tip Sleeve Ring Tip to the output jack of the external processor to line-level devices (including synthesizers and rhythm machines). For each channel, use condenser microphones. These connections require...

Owner's Manual - Page 19

...level is +4 dB. Connect an external mixer output here. Connect an additional PA system here. E FOOT SW EFFECT 2 ON/OFF jack A separately sold Yamaha FC5 foot switch can be connected to ...OUT fader (control panel K). EMX5000-20/EMX5000-12-Owner's Manual The nominal output level is +4 dB. 9 EFFECT SEND 1 jack, EFFECT SEND 2 jack The input of a sub mixer or external effect processor. The ...

Owner's Manual - Page 21

... R bus will be output from the speakers connected to jacks A and B respectively. EMX5000-20/EMX5000-12-Owner's Manual When this switch is in the AUX 1-AUX 2 position, the ...value. The speaker impedance requirement varies depending on how you connect speakers to speaker jacks. Installation/Connections 19 Installation/Connections Installation The EMX5000-20/EMX5000-12 uses a forced...

Owner's Manual - Page 23

...equipment 21 Connecting input/output equipment Microphone Cassette deck CD player Foot switch (YAMAHA FC5) (EFFECT ON/OFF) Foot switch (YAMAHA FC5) (TAP) Synthesizer Drum machine 88 Effect processor (compressor) 88 ... add a subwoofer Additional/alternative PA system EMX5000-20/EMX5000-12-Owner's Manual If more speaker outputs are needed, use the ST SUB OUT jacks and the MONO OUT jack.

Owner's Manual - Page 31

... of this device, and the appropriate actions to the mixer. The load on the ampliﬁer of this ... device cools off , normal operation too great, and the protection circuit for the same channel at the same time? The POWER indicator... the peak level indicators of the cient load impedance of 4-8 ohms. EMX5000-20/EMX5000-12-Owner's Manual Use a speaker with an impedance of the connected ...

Owner's Manual - Page 32

...circuit (Power amp) Fan circuit Phantom power Option Power requirement/ Power consumption SPEAKERS: 500 W+500 W/4Ω @0.5% THD at 1 kHz 325 W+325 W/8Ω @0.5% THD at 1 kHz BRIDGE: 1000 W/8Ω @0.5% THD at 1 kHz 20 Hz-20 kHz +1 dB, -3 dB @1 W output into 8Ω (SPEAKERS OUT) 20 Hz-20... input) FC5 (Foot switch), RK-124 (EMX5000-12) USA and Canada:120 V AC 60 Hz, 400 W Europe: ...

Owner's Manual - Page 33

...in EN55103-1 and EN55103-2. Unbalanced. 2. before clip mixer CH INPUT A -60 (CH1-8/1-16) -16 CH INPUT B -60 (CH1-8/1-16) -16 ST INPUT -34 (CH9-12/17-20) +10 ST SUB IN (1, 2) 2TR IN... Weight Accessories 682 × 158 × 538 mm (EMX5000-20) / 478 × 158 × 538 mm (EMX5000-12) 19 kg (EMX5000-20) / 15 kg (EMX5000-12) Power cord, Owner's Manual s Input speciﬁcations...