Weider Cross Bow By 1500e Support Question
Weider Cross Bow By 1500e Support Question
Find answers below for this question about Weider Cross Bow By 1500e.Need a Weider Cross Bow By 1500e manual? We have 1 online manual for this item!
Question posted by thepaulfrederich on April 13th, 2021
Need Replacement Seat Both Pieces For A 1500e Cross Bow Weider
need replacement seat. both pieces for a 1500e cross bow weider. I only have the longer seat but broken brackets so cannot do any incline exercises
Current Answers
Answer #1: Posted by Odin on May 5th, 2021 10:20 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,710
Member since:
April 10th, 2010 Points: 41,236,710
If you can't get it from Weider [use the contact information at https://www.contacthelp.com/weider/customer-service], try https://www.fitnessrepairparts.com/part_search/PartNumberSearch/.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Weider Cross Bow By 1500e Manual Pages
English Manual - Page 1
... manual for future reference. USER'S MANUAL
Visit our website at www.weiderfitness.com
new products, prizes, fitness tips, and much more! As a manufacturer, we are committed to providing complete customer satisfaction. CALL ...for future reference. Serial Number Decal (under seat)
QUESTIONS? If you have questions, or if a part is damaged or missing, PLEASE CONTACT OUR ...
English Manual - Page 2
...PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before beginning assembly. MAX by WEIDER is missing or illegible, call the toll-free telephone number on the resistance... IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENTS 13 CABLE DIAGRAM 16 EXERCISE GUIDELINES 17 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and ...
English Manual - Page 3
...resistance system before using the resistance system.
1. Replace any other type of all times.
12. ...personal injury or property damage sustained by WEIDER MAX PACK. Do not hang on .... ICON assumes no responsibility for foot protection while exercising.
9. Inspect and properly tighten all cables at...standing on a level surface, with the seat in place and fully tightened each time the...
English Manual - Page 4
... Knob Upright
Storage Knob
Backrest Seat
Leg Lever
Top Frame Lat Tower High Pulley Resistance Bars "U"-Channel
Foot Plate Low Pulley Base Plate Seat Knob
Lat Bar
4
To help...needed under warranty, you must register the resistance system at www.weiderservice.com/registration. Whether your goal is WESY5863.0.
To avoid a registration fee for selecting the innovative MAX by WEIDER 1500E...
English Manual - Page 6
...103mm Bolt (66) with the welded tubes at the bottom.
Attach the Foot Plate (23) and the Cross Tube to the Upright (3) with the Bolt and an M10 Nylon Locknut (76). Note that the front.... Do not overtighten the Nylon Locknut; Orient the Cross Tube (11) as shown, with grease. Press a 38mm x 76mm Inner Cap (99) into the top of the Cross Tube (11).
the
Wheel must be able to ...
English Manual - Page 8
... two M6 Nylon Locknuts (69). Make sure that the wide sides of the Bench Rail (5) and properly tighten the M8 Flange Nuts (19). Attach the Seat Knob (45) to roll easily. 9. Make sure that the slot in the Knob is aligned with the slot in the same manner.
10.
Make sure...
English Manual - Page 9
... Frame (15) with four M4 x 16mm Screws (62).
13. Hold the Backrest Frame vertically over the Seat Carriage and slide the rod into the slot, as shown.
Attach the two Guard Plates (17) to the... slot in the inset drawing.
14. Orient the Backrest (14) and the Backrest Backing (8) as shown in the Seat Carriage (12). Using twelve M4 x 12mm Flat Head Screws (85), attach the two 10-pound Caps (101) ...
English Manual - Page 10
Make sure the indicated rings are on the indicated end of the Cross Tube (11) and then through a Swivel Arm (22). Orient the Cover Plate (72) as shown in the ...x 42mm Button Head Bolt (71) and an M10 Nylon Locknut (76).
18. Slide the Tray (35) onto the rods on the Cross Tube (11). If necessary, use the tip of a screwdriver to the indicated "U"channel on this side
4
35
18 18 17
44 ...
English Manual - Page 11
...with an M10 Nylon Locknut (76). Make sure that
the flat edge of the welded rod in the Cable.
23
Insert the end of the Cross Tube (11) and then through the welded tube on the 10-pound
Center Resistance Bar (not shown). Wrap the Long Cable (80) around ... the Long Cable (80) through the remaining Swivel Arm (22). Insert the Swivel Arm (22) into the welded tube on the Cross Tube (11).
English Manual - Page 12
... (90), two 26mm Spacers (52), two M10 Washers (75), and an M10 Nylon Locknut (76). Attach the Pulley to be sure that the Pulley is longer. Press four 19mm Round Inner Caps (78) into the ends of the Bench Rail (5).
26. Locate the two Short Cables (33). Make sure that is...
English Manual - Page 13
Replace worn parts immediately.
Attach the other high pulley in the Bench Rail.
See the EXERCISE GUIDELINES on page 17 for each time the resistance system is used. Do not ... when not in order to lift up on page 15). Also, refer to the accompanying exercise guide to see ADJUSTING THE BACKREST on the Seat in use the Leg Lever (not shown), attach the two ends of the Leg Lever ...
English Manual - Page 14
...resistance will increase rapidly. Do not add or remove Resistance Bars from the "U"-channels, start with the heaviest resistance bar to be replaced with the other end of the resistance bar. As the resistance bars begin to the Long Cable (80) with a Cable ... removing resistance bars from the "U"-channels while an end of the Long Cable (80) is needed, add one resistance bar at a time.
English Manual - Page 15
... (5) next to one of three inclined positions.
Next, remove the Storage Knob (30) from the "U"-channels on the 10-pound Center Resistance Bar (44) (see ADJUSTING THE SEAT on the bottom of the Bench Rail...Knob into the side of the other three adjustment holes in this area
5
Hook For row exercises, remove the Backrest (14). Note: Storing the resistance bars vertically will go. Be sure that...
English Manual - Page 16
...CABLE DIAGRAM
The cable diagram shows the proper routing of the Tray (35).
67 36
To replace the Removable Resistance Bars (36, 67), slide them into the Tray (35) from the resistance...route for the Cable.
5
Long Cable (80)
7 6
4
3
2 1
16 Use the diagram to exercise apart from the side shown, so that the Cable has been assembled correctly. USING THE REMOVABLE RESISTANCE BARS
The ...
English Manual - Page 17
.... Cross Training Cross training is right for you perform. Determining the exact length of time for every major muscle group, emphasizing areas that is an efficient way to 20 repetitions as possible without discomfort.
Select exercises for each workout, as well as many sets of 15 to get a complete and well-balanced fitness program...
English Manual - Page 18
... (upper back)
P. out. • Rest for 30 seconds after each set for each exercise. Move
slowly as you stretch and do not bounce. Remember, the key to achieving the greatest results is ...
building workout. • Rest for one minute after each set. List the date, the exercises performed, the resistance used to 10 minutes of stretching. Include stretches for a toning work- ...
English Manual - Page 19
MONDAY
Date: //
EXERCISE
RESISTANCE
SETS
REPS
TUESDAY
Date: //
AEROBIC EXERCISE
WEDNESDAY
Date: //
EXERCISE
RESISTANCE
SETS
REPS
THURSDAY
Date: //
AEROBIC EXERCISE
FRIDAY
Date: //
EXERCISE
RESISTANCE
SETS
REPS
Make photocopies of this page for scheduling and recording your workouts.
19
English Manual - Page 22
... x 72mm Bolt
7
1
Leg Lever
65
4
M8 Nylon Locknut
8
1
Backrest Backing
66
1
M10 x 103mm Bolt
9
1
Seat Backing
67
1
10-pound Removable Resistance
10
1
Top Frame
Bar
11
1
Cross Tube
68
2
Long Handle
12
1
Seat Carriage
69
2
M6 Nylon Locknut
13
1
Seat
70
2
M10 x 65mm Button Head Screw
14
1
Backrest
71
6
M10 x 42mm Button Head Bolt...
English Manual - Page 24
... gives you . ORDERING REPLACEMENT PARTS
To order replacement parts, see the PART LIST and EXPLODED DRAWING in the
center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants...warranties and any implied warranties of merchantability or fitness for which vary from the service center will be pre-authorized by WEIDER 1500E resistance system) • the SERIAL NUMBER of...
Similar Questions
I Need A Replacement Cable For My Welder Pro 8900 Do You Guys Carry One?
(Posted by mjdunkin21 3 years ago)
I Need To Replace The Resistance Cylinders So Where Can I Get Them?
Where can I get the resistance cylinder for the Weider CJXT3 Master Trainer 70092?
Where can I get the resistance cylinder for the Weider CJXT3 Master Trainer 70092?
(Posted by diego52191 3 years ago)
I Need To Purchase Replacement Bolts. How Much Are They?
(Posted by jchavez99981 3 years ago)
Need A Replacement Bench Cushion#11 On Parts List. Where�· Can I Get One
for weider 500 weight machine
for weider 500 weight machine
(Posted by walteradkins7 8 years ago)
I Need To Replace Cable For Chest And Leg Station. Both Use The Same Cable.
(Posted by vnvpirate 9 years ago)