Troy-Bilt TB675 Support Question
Troy-Bilt TB675 Support Question
Find answers below for this question about Troy-Bilt TB675.Need a Troy-Bilt TB675 manual? We have 1 online manual for this item!
Question posted by jamesbacon239 on May 19th, 2014
Head Quit Spinning. Found Out Gear Is Stripped Out But Cannot Find The Part.
Found out gear is stripped out but searched parts for this trimmer but could find no replacement part. Any idea on where i can find and order this part?
Current Answers
Related Troy-Bilt TB675 Manual Pages
Operation Manual - Page 1
Operator's Manual
Electric Start Capable 4-Cycle Trimmer
TB675 EC
TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 ... the assembly, controls, operation or maintenance of authorized service dealers near you. When servicing, use only identical replacement parts.
769-08458 / 02
All information, illustrations, and specifications in Canada. Copyright© 2013 MTD SOUTHWEST INC...
Operation Manual - Page 2
... obey a safety WARNING signal CAN result in effective working order, or the engine be constructed, equipped and maintained for ...rules must be
followed. Check for proper accident prevention measures. Replace parts that certain internal combustion engines operated on U.S. DO NOT smoke....8226; Always add fuel in serious injury to the head, hands and feet.
• Carefully inspect the area...
Operation Manual - Page 3
Secure hair above shoulder level.
• The cutting head shield must be in place while operating the unit. Do not operate the...all moving parts.
• Do not touch the engine, gear housing or muffler. Clean the unit after the unit is turned off and disconnect the spark plug for maintenance or repair.
• Use only original equipment manufacturer (OEM) replacement parts and accessories...
Operation Manual - Page 4
You may appear on trimmer attachment
shield. These parts get burned. SYMBOL MEANING
• SAFETY ALERT SYMBOL Indicates danger, warning or caution. May be propelled at least 50 feet (15 m) from the operating area.
&#...
Operation Manual - Page 5
...Filter Cover
Throttle Control
Fuel Cap Choke Lever
Coupler
Oil Fill Plug
Cutting Head
Cutting Head Shield
Line Cutting Blade
SPECIFICATIONS*
Engine Type Air-Cooled, 4-Cycle Displacement...etc. Other optional accessories may be used with cutting head, cutting head shield and handle 13 - 14 lbs. (5.9 - 6.4 kg) Trimmer Mechanism Bump Head Trimming Line Diameter 0.095 inches (2.41 mm) Cutting...
Operation Manual - Page 6
...with a 3/8" socket, but do not tighten the bolt completely.
3. Place the cutting head shield onto the mount bracket. Tighten the screws equally. Place it through (Fig. ... the type of shaft and shield equipped with a 3/8" socket until finger tight.
3. Mount Bracket
Cutting Head Shield Fig. 1
INSTALLING AND ADJUSTING THE HANDLE
Installing the Handle
1. Adjusting the Handle
If the handle ...
Operation Manual - Page 7
... personal injury or damage to tighten (Fig. 3).
For decorative edging with a string trimmer attachment, lock the release button into
the primary hole only. While firmly holding the ... THE COUPLER
The coupler enables the use of the coupler (Fig. 5).
90˚ Edging Hole (Trimmer Only)
Coupler
Fig. 3
Knob
Release Button
Nut Fig. 4
Primary Hole
Guide Recess
Upper Shaft Housing...
Operation Manual - Page 12
OPERATION
HOLDING THE TRIMMER
WARNING: Always wear eye, hearing, hand, foot and
body protection to reduce the risk of trimming line is... This unit is tapped, about 1 inch (25.4 mm) of injury when operating this unit.
• Stand in the cutting head shield will cut thick vegetation • Forcing the line into objects such as walls or fence posts
DECORATIVE TRIMMING When trimming around trees...
Operation Manual - Page 13
... unit from the cutting head. MAINTENANCE SCHEDULE
Perform these procedures, take the unit to overheat or fail. NOTE: Maintenance, replacement, or repair of the cutting head (Fig. 17). FREQUENCY...line and/or obstructions from starting accidentally. Other types of trimming line may be a part of equal length. 5.
MAINTENANCE
WARNING: To prevent serious injury, never perform
maintenance or...
Operation Manual - Page 14
... fill plug (Fig. 20). Stop the engine and allow it to Adding Oil. The cutting head shield should fill the window approximately halfway (Fig. 20). Add oil to clean the inner reel...should hang over the edge so that may cause the oil to prevent debris
from the cutting head. 1.
CHECKING THE OIL LEVEL
WARNING: OVERFILLING THE CRANKCASE MAY
CAUSE SERIOUS PERSONAL INJURY. Removing...
Operation Manual - Page 16
....
2. Do not over tighten.
6. ADJUSTING THE IDLE SPEED
WARNING: The cutting head may spin during idle speed
adjustments.
NOTE: Careless adjustments can seriously damage the unit. Release ... dirty, replace it to : 110-120 in . (0.635 mm)
Fig. 25
16 Grit in the cylinder head. Tighten the spark plug with a 5/8-inch socket, turning it from the cylinder head with a replacement part #753-...
Operation Manual - Page 17
... use or damage. • Store the unit in a horizontal position. Reinstall the spark plug.
4. Repair or replace damaged parts and tighten loose screws, nuts or bolts. Change the oil. Wipe off any loose or damaged parts. Store the unit in a dry, well-ventilated area. • Store the unit out of the reach of...
Operation Manual - Page 18
... fuel Stop the engine and clean the cutting head Clean or replace the air filter
Drain the fuel tank and add fresh fuel Clean or replace the air filter Replace the spark plug
THE CUTTING HEAD WILL NOT ADVANCE LINE The cutting head is bound with grass The cutting head is out of line The inner reel...
Operation Manual - Page 20
...improve the design of any Troy-Bilt Product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for products sold or exported ... express warranty or guaranty, whether written or oral, except as mentioned above as to the parts as to this Warranty: This warranty gives you specific legal rights, and you .) In no...
Similar Questions
The Head Will Not Turn.
The unit starts but the head will not rotate....looks as though some sort of drive cable has snapppe...
The unit starts but the head will not rotate....looks as though some sort of drive cable has snapppe...
(Posted by wsmharp 8 years ago)
It Runs Great But When I Pull The Trigger, The Head Won't Spin.
The head quit spinning, the engine starts and runs great but when I pull the trigger , the head won'...
The head quit spinning, the engine starts and runs great but when I pull the trigger , the head won'...
(Posted by Rjkaplan7 8 years ago)
Changing Trimmer Head On Troy-bilt Tb6044 Xp
I have a TB6044 XP and want to replace the trimmer head with a Pivotrim hybrid. But cannot remove th...
I have a TB6044 XP and want to replace the trimmer head with a Pivotrim hybrid. But cannot remove th...
(Posted by GCP1 8 years ago)
Oil For Troy-bilt Tb675
what kind of oil should I put in my Troy-Bilt TB675
what kind of oil should I put in my Troy-Bilt TB675
(Posted by herjeac 10 years ago)
