Troy-Bilt TB6042 XP Support Question
Troy-Bilt TB6042 XP Support Question
Find answers below for this question about Troy-Bilt TB6042 XP.Need a Troy-Bilt TB6042 XP manual? We have 1 online manual for this item!
Question posted by bourgekathy on July 19th, 2013
How Do I Put On The Steel Blade,
i need to remove the entire head to put on the steel blad ehow do I do that
Current Answers
Related Troy-Bilt TB6042 XP Manual Pages
Operation Manual - Page 1
... or www.troybilt.ca. For service, please call the Customer Support Department at the time of printing.
Operator's Manual
Electric Start Capable 4-Cycle Professional Trimmer
TB6042 XP
TABLE OF CONTENTS Service Information 1 Rules for Safe Operation 2 Know Your Unit 4 Assembly Instructions 4 Oil and Fuel Information 5 Starting and Stopping Instructions 6 Operating Instructions...
Operation Manual - Page 2
...to these requirements could subject you must follow the safety
rules. Wash hands after handling. Remove all warnings and safety instructions. there still may result in injury
to cool before starting... line beyond the length of fire, electric shock and personal injury. Attention is to the head, hands and feet.
• Wear safety glasses or goggles that are cracked, chipped, or...
Operation Manual - Page 3
... original equipment manufacturer replacement parts and accessories for a short time.
• SHARP BLADE
WARNING: Sharp blade on both hands when operating. OTHER SAFETY WARNINGS
• Never store the unit...describes safety and international symbols and pictographs that fuel containing greater
than the speed needed .
• UNLEADED FUEL Always use or damage. Always keep the engine ...
Operation Manual - Page 4
...
Shield
guard mount bracket. (Fig. 2)
2. Minimum
3. Screw (4)
Guard Mount Bracket
3. Place the cutting head shield onto the guard Cutting
mount bracket, making sure to the
6 in place. (Fig. 2)
Fig. ...to the unit. (Fig. 5)
Fig. 3
Support Clip
Cutting Head
Line Cutting Blade
Adjustment Tab
Fig. 4
Support Fitting
Fig. 5
4 Shaft
• Edging
Grip
• Decorative trimming around trees...
Operation Manual - Page 5
... gas tank.
5 Oil Fill Hole Fig. 7
1.
As little as needed . Avoid creating a source of oil in the
crankcase is unavoidable, follow...the Oil. Oil Fill Plug Replace the top. Pour the entire bottle of fuel additives, such as ethanol, methanol or ... Using a fuel additive can cause premature engine wear and failure. Remove the oil fill plug from forming harmful deposits in a clean,...
Operation Manual - Page 6
...8. Move the choke lever to Position 1 (Fig. 11).
5. Continue to squeeze the throttle control, remove the electric starter or drill from the unit and allow the engine to turn the unit on . IF.... 11).
5. Press and hold the On/Off Control switch in a confined area. NOTE: Unit is no need to cool down by idling.
2. the engine does not start , go back to a complete stop (Fig....
Operation Manual - Page 7
...grass over
Fig. 16
7 WARNING: Do not remove or alter the line cutting blade
assembly. Removing the Cutting Attachment or Add-On
WARNING: To...
WARNING: Before you to release trimming line without the need to reduce the risk of trimming line is released. ... Entanglement with the attachment. For best results, tap the cutting head on , push it straight into objects such as the cutting line...
Operation Manual - Page 8
... are unsure about 5 in. (12.7 cm) is visible from the cutting head. NOTE: Make sure the O-ring is removed from
both sides of the line (Fig. 20).
Fill
3. Dispose of oil.... Disconnect the spark plug wire to federal, state
and local regulations.
4. These procedures should be performed by the line blade...
Operation Manual - Page 9
... the air filter, you will not idle, adjust the idle speed screw as needed ) until snug. Remove the engine cover (Fig. 34). 3. Spark Plug
5. Measure the clearance between...Remove the spark plug from the cylinder head by an authorized service dealer.
Torque the screw to the top of the engine cover with a large flat blade screwdriver or
Torx® T-25 bit (Fig. 35). Remove...
Operation Manual - Page 10
... notice.
10 Household cleaners that all of line is exposed
Push the bump head and pull out line until the unit starts. Remove the spark plug and put 5 drops of the unit. Pull the starter...serious personal injury, always turn the
unit off and allow it to run until it . NOTE: Remove the spark plug and drain all
gasoline has been drained from the cylinder before storing. • ...
Similar Questions
What Type Of Oil Is Required For A Troy Bilt Tb 6042xp String Line Trimmer?
(Posted by Stlouboo 3 years ago)
Damaged Blade
My Troy-Bilt Storm 2840 Snowblower's front blade that goes into the ground has been damaged. My ques...
My Troy-Bilt Storm 2840 Snowblower's front blade that goes into the ground has been damaged. My ques...
(Posted by skmatias 3 years ago)
Attachments For Tb2044 Xp
Where can I purchase the edger attachment for the tb2044xp
Where can I purchase the edger attachment for the tb2044xp
(Posted by williefields357 8 years ago)
Changing Trimmer Head On Troy-bilt Tb6044 Xp
I have a TB6044 XP and want to replace the trimmer head with a Pivotrim hybrid. But cannot remove th...
I have a TB6044 XP and want to replace the trimmer head with a Pivotrim hybrid. But cannot remove th...
(Posted by GCP1 8 years ago)