Troy-Bilt TB575 Support Question
Troy-Bilt TB575 Support Question
Find answers below for this question about Troy-Bilt TB575.Need a Troy-Bilt TB575 manual? We have 2 online manuals for this item!
Question posted by jwest011 on April 14th, 2021
How Do You Remove A Speed Spool Its Orange Colored. On A Tb575ss.
the black button on the bottom that your suppose to turn counterclockwise won't turn.
Current Answers
Answer #1: Posted by techyagent on April 14th, 2021 12:28 PM
techyagent
Member since:
June 17th, 2014 Points: 4,799,790
Member since:
June 17th, 2014 Points: 4,799,790
Related Troy-Bilt TB575 Manual Pages
Operation Manual - Page 1
... of the operator and any time without notice. Please keep these instructions for regulations pertaining to follow the safety rules. P/N 769-01920A
4-Cycle Gasoline Trimmer
TB575SS & TB525CS
SAVE THESE INSTRUCTIONS
For service call 1-800-520-5520 in the United States, or 1-800-668-1238 in this unit both within and after...
Operation Manual - Page 2
...order to provide the best grip.
• Be sure the cutting attachment is turned off and become lodged between the cutting attachment and shield.
• To reduce ...Remove the fuel cap slowly, and only after each use of the
shield.
• This unit has a clutch.
SAVE THESE INSTRUCTIONS
2 Breathing exhaust fumes can break off .
• Do not operate the engine faster than the speed...
Operation Manual - Page 3
...only. (4) Screws
To Install
D-Handle
1. Remove the screws and
bottom clamp piece that were installed on this unit. Do not tighten until the D-handle is turned off.
• SHARP BLADE
WARNING: Sharp ...Always use clean, fresh unleaded fuel
• ON/OFF STOP CONTROL ON / START / RUN
TB525CS & TB575SS
• OIL
Refer to move it a
minimum of 15.24 cm (6
in conjunction with a large...
Operation Manual - Page 4
...start the unit. Add 0.8 oz. (23 ml.) of fuel additive per gallon of oil and remove the
paper seal covering the
opening. Never operate the unit without oil. Wipe up any spilled fuel...creating a source of oil in the crank case; Gas Can Spout
Fuel Tank Fig. 5
4
Fuel Cap Remove the oil fill plug from forming harmful deposits in the fuel can
Fig. 2
be overemphasized. NOTE: This is...
Operation Manual - Page 6
... EZ-Link™ coupler (Fig. 10). EZ-Link™ Coupler
Release Button Primary Hole
WARNING: Before you begin using the line head cutting attachment with the attachment.
Removing the Cutting Attachment or Add-On 1. Turn knob counterclockwise to the unit. Turn the knob counterclockwise to the unit, shut the unit off before operating this attachment with...
Operation Manual - Page 7
...8226; Attempting to cut the line to the proper length if excess line is at high speed. Move either in the operating position (Fig. 12). This may stall.
Line release becomes ...throttle.
• Keep the cutting attachment parallel to bend over 8 inches (200 mm) by removing all vegetation around a tree. Always keep the trimming line fully extended. Cutting shorter lengths produces the...
Operation Manual - Page 8
...pre-wound inner reel
Winding the Inner Reel With New Line
NOTE: It Is unnecessary to remove the bump knob to ensure that the unit cannot start. NOTE: Maintenance, replacement, or repair...engine exhaust port may make the engine overheat or fail. Hold the outer spool and turn the inner reel counterclockwise to any non-road engine repair establishment, individual or authorized service dealer. ...
Operation Manual - Page 9
... the line jams, pull the ends of the line firmly from the outer spool.
3. Continue winding the inner reel counterclockwise until the oil level reaches the inner most thread (Fig. 27). 6. INSTALLING A PRE-WOUND REEL
1. Turn the bump knob counterclockwise and remove the bump knob, spring and foam seal (Fig. 20). Fig. 19
2. Pull the...
Operation Manual - Page 10
...
Fig. 31
2. AIR FILTER MAINTENANCE
WARNING: To avoid serious personal injury, always turn the unit off and allow it to prevent injury when handling unit. Position the ... Checking the Oil Level.
Wash the filter in poor performance or can cause permanent damage to spread and remove excess oil (Fig. 34). 6. Apply enough clean SAE 30 motor oil to prevent accidental starting.
Fig...
Operation Manual - Page 11
... stops, insert a small phillips in . Turn the idle speed screw in, clockwise, 1/8 of its travel while looking in a clean, dust free area.
1. Disconnect the spark plug wire.
3. Remove the spark plug from around the rocker arm cover. socket counterclockwise.
4. View Of The Rear Engine Cover
Remove Screws
Remove Screws
Fig. 38
5. Remove the rocker arm cover and...
Operation Manual - Page 12
.... Valve Stem
Fig. 41
12. Check alignment of operation and check its condition.
1. Remove the six (6) screws on the back of the engine cover with a slight amount of... mm) wrench or nut driver (Fig. 40). • To increase clearance, turn the adjusting nut
counterclockwise. • To decrease clearance, turn the adjusting nut
clockwise. Grit in . (0.655 mm.). Clean dirt from around ...
Operation Manual - Page 13
...a soft cloth.
With a flat blade screwdriver or Torx T-20 bit and a T-25 bit, remove the screws attaching the spark arrestor cover to cool before transporting.
• Secure the unit while ...of high quality motor oil into a container. Remove the spark arrestor screen from the carburetor.
3. WARNING: To avoid serious personal injury, always turn your unit off any loose or damaged parts...
Operation Manual - Page 14
...Improper carburetor adjustment Cutting attachment bound with grass Dirty air filter Plugged spark arrestor
ACTION Turn On/Off control to ON Fill fuel tank with new fuel Press primer bulb fully...clean cutting attachment Refill with new line Replace the inner reel Clean inner reel and outer spool Disassemble, remove the welded section and rewind Disassemble and rewind the line Push the bump knob and ...
Operation Manual - Page 15
...4-Cycle Displacement...1.8 cu. in. (29 cc) Operating RPM...6,800+ rpm Idle Speed RPM ...2,800 - 3,600 rpm Ignition Type ...Electronic Ignition Switch ...Rocker Switch ..., cutting attachment and shield 11.5-13.0 lbs (5.2-5.9 kg) Cutting Mechanism ...SpeedSpool® Line Spool...Bump Line Releaser Line Spool Diameter ...4 inches (101.6 mm) Trimming Line Diameter ...095 inches (2.41 mm) Cutting Path...
Operation Manual - Page 18
Wear items - Bump Knobs, Outer Spools,Cutting
Line, Inner Reels, Starter Pulley,Starter Ropes, Drive Belts C. Troy-Bilt... right to change or improve the design of any Troy-Bilt product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for rental expenses to temporarily replace a warranted product. (Some...
Operation Manual - Page 53
PARTS LIST
REPLACEMENT PARTS - MODELS TB575SS & TB525CS 4-CYCLE GAS TRIMMER
Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
...
Operation Manual - Page 54
PARTS LIST
REPLACEMENT PARTS - MODELS TB575SS 4-CYCLE GAS TRIMMER
1
4 1
23 56 7
10
15 Item Part No. Description
1 753-04234 Throttle Housing Assembly ...180547 Shield Mounting Hardware 22 753-1213 Shield Assembly (includes 23) 23 791-181823 Blade Assembly 24 791-181457 Outer Spool Assembly (includes 25) 25 791-181458 Retainer 26 791-181561 Thrust Washer 27 753-04257 Slider 28 791-181459 Small ...
Operation Manual - Page 55
... Mounting Screw 791-181857 Bushing Housing Assembly 791-145569 Anti-Rotation Screw 791-181659 Shield Assembly (includes 23) 753-05212 Blade Assembly 791-181457 Outer Spool Assembly (includes 25) 791-181458 Retainer 791-181561 Thrust Washer 791-181459 Small Spring 753-04257 Slider 791-181532 E-Clip 791-181531 Spring 791-181462...
Similar Questions
How To Replace The Starter Rope.
The starter rope of my TB575 EC has come off of the starter housing assembly (spool) and is rapped a...
The starter rope of my TB575 EC has come off of the starter housing assembly (spool) and is rapped a...
(Posted by paparowe62 8 years ago)
Remove Head On Tb575 Ec
I want to replace the head on my TB575 EC because it's broken. I have already taken the gear box off...
I want to replace the head on my TB575 EC because it's broken. I have already taken the gear box off...
(Posted by tamtmnguyen 9 years ago)
How To Remove Full String Head From Tb625ec
I need to remove the complete string head, how do I do it?
I need to remove the complete string head, how do I do it?
(Posted by denniscmalinowski 9 years ago)
Remove The Cutting Head
I want to know how to remove the cutting head of TB2044XP trimmer
I want to know how to remove the cutting head of TB2044XP trimmer
(Posted by jthannikary 10 years ago)
