Troy-Bilt TB575 Support Question
Troy-Bilt TB575 Support Question
Find answers below for this question about Troy-Bilt TB575.Need a Troy-Bilt TB575 manual? We have 2 online manuals for this item!
Question posted by meoconnor1 on May 31st, 2014
How Much Oil Is Needed If Changing The Oil?
The person who posted this question about this Troy-Bilt product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Troy-Bilt TB575 Manual Pages
Operation Manual - Page 1
...
TABLE OF CONTENTS
Service Information 1 Rules for Safe Operation 2 Know Your Unit 3 Assembly Instructions 3 Oil and Fuel Information 4 Starting/Stopping Instructions 5 Operating Instructions 6 Maintenance and Repair Instructions 8 Cleaning and ...Please keep these requirements could subject you to make changes at any bystanders. PROOF OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE.
Operation Manual - Page 2
... engine when cutting is turned off.
• Do not operate the engine faster than the speed needed to Starting/Stopping Instructions.
• Use the right tool. Do not smoke while fueling. Keep...Clean cutting blades with both hands when operating. If you strike or become entangled with machine oil to prevent rust.
• Lock up high to prevent unauthorized use metal-reinforced line, ...
Operation Manual - Page 3
...off.
• SHARP BLADE
WARNING: Sharp blade on the Dhandle for the proper type of oil. To Adjust
4. RULES FOR SAFE OPERATION
SAFETY AND INTERNATIONAL SYMBOLS
This operator's manual describes ... Z87.1 standards and ear protection when operating this product. Use a full face shield when needed.
• KEEP BYSTANDERS AWAY
WARNING: Keep all warnings and safety instructions. These parts get...
Operation Manual - Page 4
... minimize the formation of fuel additives, such as needed .
NOTE: Do not overfill the tank.
3.
See Changing the Oil.
1. Fig. 4
RECOMMENDED FUEL TYPE Old fuel is facing up any gasoline that may have spilled and reinstall the oil fill plug.
Never operate the unit without oil. Check the oil before filling the fuel tank. Unscrew the...
Operation Manual - Page 5
...be lethal in Position 3 and squeeze the throttle control. Allow the
engine to Checking the Oil Level.
2. APPLICATIONS As a trimmer: • Cutting grass and light weeds • Edging ...• Decorative trimming around trees, fences, etc.
5
Throttle Control Fig. 8 Check the oil level in the starting position when pulling the starter rope (Fig. 8). Crouch in the crankcase. Pull...
Operation Manual - Page 7
..., the left improves the unit's cutting efficiency. ADJUSTING TRIMMING LINE LENGTH
The Bump Head™ cutting attachment allows you to release trimming line without the need to bend over 8 inches (200 mm) by removing all vegetation around a tree. Each time the head is bumped, about 1 inch (25.4 mm) of the line...
Operation Manual - Page 8
...; trimming line:
• Wind the inner reel with fresh fuel Check oil
Clean and re-oil air filter
Change oil Change oil Clean spark arrestor Check rocker arm to valve clearance and adjust Check rocker arm...may result from the outer spool until approximately four (4) inches (102 mm) of the two eyelets in need of line.
8. The line will form a small
loop (Fig. 17) when it is tight against ...
Operation Manual - Page 9
... the area around the dipstick before each use a flashlight if needed. Oil Fill Plug
MaxOil Fill Line Fig. 27
O-Ring Oil Fill Hole
Fig. 28
9
If the oil level is not touching the inner most thread on the oil fill plug when checking and changing the oil (Fig. 28).
Fig. 23
5. Install new line as
Shaft
described...
Operation Manual - Page 10
... carry away more impurities. 1. Wash the filter in the slot on the bottle measures approximately 3.04 ounces (90 ml) (Fig. 30). MAINTENANCE AND REPAIR INSTRUCTIONS
CHANGING THE OIL For a new engine, change the oil after the first 10 hours of
the cover inward. Unplug spark plug boot to prevent accidental starting...
Operation Manual - Page 11
..., dust free area.
1.
A dirty air filter will not idle, adjust the idle speed screw as needed ), to making any adjustments. If, after the first 10 hours of operation and every 25 hours of...sure the cutting attachment has stopped rotating before adjusting the idle speed screw. Refer to Oil and Fuel
Information. Clean dirt from around the rocker arm cover. Refer to Air Filter...
Operation Manual - Page 13
... or handle. Reinstall the spark plug.
NOTE: Remove the spark plug and drain all gasoline has been drained from the cylinder before transporting. Change the oil, referring to distribute the oil. Repair or replace damaged parts and tighten loose screws, nuts or bolts. TRANSPORTING
• Allow the engine to cool before transporting.
•...
Operation Manual - Page 14
... Push the bump knob and pull out line until 4 inches (102 mm)
of line is outside of the cutting attachment
CUTTING LINE ADVANCES UNCONTROLLABLY CAUSE
Oil, cleaner or lubricant in cutting head
ACTION Clean and thoroughly dry the cutting head
If further assistance is required, contact your authorized service dealer.
14
Operation Manual - Page 15
... right to make changes at the time of printing. in. (29 cc) Operating RPM...6,800+ rpm Idle Speed RPM ...2,800 - 3,600 rpm Ignition Type ...Electronic Ignition Switch ...Rocker Switch Valve clearance...0.003-0.006 in. (0.076-0.152 mm) Spark Plug Gap ...0.025 inch (0.655 mm) Lubrication ...SAE 30 Oil Crankcase Oil Capacity ...3.04 oz...
Operation Manual - Page 18
..., Inner Reels, Starter Pulley,Starter Ropes, Drive Belts C. Troy-Bilt reserves the right to change or improve the design of the product as to misuse, abuse, commercial use the product. Troy...replacement of any Troy-Bilt product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for products sold or ...
Operation Manual - Page 53
... Assembly (includes 2 & 3) Cover Screw Screw Rocker Cover Rocker Cover O-Ring Cylinder Assembly (includes 3, 5 & 9) Piston Ring Assembly Piston Assembly (includes 7) Cylinder O-Ring Breather Hose Oil Plug (includes 12) Oil Plug O-Ring Crankcase Cover Crankcase Cover O-ring Crankcase Assembly (includes 9, 10 & 14) Flywheel Assembly Cam Bracket Assembly (includes 18) Cam Bracket Screw Lead Wires...
Parts List - Page 2
... Assembly (includes 2 & 3) Cover Screw Screw Rocker Cover Rocker Cover O-Ring Cylinder Assembly (includes 3, 5 & 9) Piston Ring Assembly Piston Assembly (includes 7) Cylinder O-Ring Breather Hose Oil Plug (includes 12) Oil Plug O-Ring Crankcase Cover Crankcase Cover O-ring Crankcase Assembly (includes 9, 10 & 14) Flywheel Assembly Cam Bracket Assembly (includes 18) Cam Bracket Screw Lead Wires...
Similar Questions
How Do You Change The Oil In The 410-420 Model Wood Chipper
oil change for 410-420
oil change for 410-420
(Posted by Stepal66022 5 years ago)
Troy Cs 4325 Oil Change Procedure
How do I change the oil in my chipper shredder
How do I change the oil in my chipper shredder
(Posted by gbaker1951 9 years ago)
Remove Head On Tb575 Ec
I want to replace the head on my TB575 EC because it's broken. I have already taken the gear box off...
I want to replace the head on my TB575 EC because it's broken. I have already taken the gear box off...
(Posted by tamtmnguyen 9 years ago)
Why Is Weed Wacker Smoking When Turn On And It Leaks Oil True Filter Area
(Posted by late4work5 10 years ago)