Troy-Bilt CS 4265 Support Question
Troy-Bilt CS 4265 Support Question
Find answers below for this question about Troy-Bilt CS 4265.Need a Troy-Bilt CS 4265 manual? We have 2 online manuals for this item!
Question posted by Stepal66022 on July 19th, 2018
How Do You Change The Oil In The 410-420 Model Wood Chipper
oil change for 410-420
Current Answers
Related Troy-Bilt CS 4265 Manual Pages
Operation Manual - Page 1
Model Series 410 & 420
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. Printed In USA
TROY-BILT LLC.... 769-06007A June 7, 2011
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Model Series 410 Shown
Chipper Shredder -
Operation Manual - Page 2
... machine, for all engine-related issues with regards to change product specifications, designs and equipment without notice and without first..., operation, or maintenance of product specifications for purchasing a Chipper Shredder manufactured by standing at the operator's position and looking... illustrated in this machine, you can locate the model plate by Troy-Bilt. You can seek help from...
Operation Manual - Page 3
.... Do not put hands and feet near rotating parts or in a poorly ventilated area. Wear sturdy, rough-soled work gloves when feeding material in the chipper chute.
4.
Failure to the machine.
2. Be familiar with any damage at least 75 feet from the machine while it against the engine. Never allow adults...
Operation Manual - Page 4
...feet.
2. Never operate without good visibility or light.
13. Never empty or change clothes immediately. Never pick up oil or fuel spillage and remove any metal, rocks, bottles, cans, or other...Gasoline is spilled, wipe it against the engine before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are not covered in the feeding chambers and discharge...
Operation Manual - Page 5
Do not change the engine governor settings or overspeed the engine. The governor controls the maximum safe operating ... (OC), Secondary Air Injection (SAI) and Three Way Catalyst (TWC) if so equipped.
5. Failure to the operator's manual for gas, oil, Resources Code). Section 2 - Disconnect the spark plug wire and ground it to operate on federal lands.
12. are certified to operate at...
Operation Manual - Page 7
...One Safety Glasses
Assembly
NOTE: This unit is crated with the chipper chute in the raised position.
Chipper Chute (Model Series 420 Only)
For shipping reasons, the unit is shipped without gasoline or oil in the accompanying engine manual BEFORE operating your chipper shredder. Pull the spring latch upward.
2. Positionthebagsothatthewingknobswhichsecurethechute
deflector to the operator...
Operation Manual - Page 8
...when handling gasoline.
See Fig. 3-4.
3
2 3
Figure 3-4
8
Section 3 - Add oil provided before starting unit for additional engine information.
1.
Never fuel the machine indoors or while the... other sources of the
tongue. See Fig. 3-3.
1
Set-Up
Gas and Oil Fill-Up
Refer to secure. Reinserttheclevispinthroughaligningholesinboththetongue
and the base. Fasten with gasoline as instructed...
Operation Manual - Page 9
... branches up to two inches (model series 410) or three inches (model series 420) in diameter may be fed into the chipper chute for chipping.
Recoil Starter
The recoil starter is located on the top of the engine controls. Spring Latch (Model Series 420 Only)
The spring latch is located on the chipper chute support. It is used...
Operation Manual - Page 10
...rope out slowly until the engine is running smoothly. Operation
5
WARNING: The operation of any chipper shredder can result in foreign objects being thrown into the CHOKE position. These factors depend on ...Off switches, other may not. Open fuel shut-off valve (if equipped) and make and model engine comes with this point).
10
Figure 5-2
CAUTION: Never stop the engine by moving the...
Operation Manual - Page 11
... with a diameter greater than two (2) inches (Model Series 410) or three (3) inches (model series 420) into a debris collection bag. Stop engine.
2. Empty the bag and reattach to dislodge debris located toward the base of the hopper.
3. Section 5 - Operation
11 Use a branch (or other than branches (or wood) into the chipper chute.
• Apply intermittent pressure (force...
Operation Manual - Page 12
...machine. Read and follow instructions carefully.
• Check engine oil level before , cleaning, lubricating, or performing any maintenance.
... water is not recommended as instructed here.
• Changing of engine-governed speed will void engine warranty.
•... deflector with water. Equipment Care
• Clean the chipper shredder thoroughly after each season.
• Periodically check ...
Operation Manual - Page 13
... are sharp. to purge any remaining debris from the clevis pin which extends through the housing and shredder screen. chipper shredder has come to the chute deflector, if desired.
2. See Fig. 6-1B.
Reattach the debris collection bag to a complete stop. Remove the two wing knobs ...
Operation Manual - Page 14
...removing the two hex bolts and saddle washers which secure it to the impeller. C
B
A
Model Series CS 3210 Shown
Figure 7-1
4. Pivot the shredder screen upward as instructed under the heading Cleaning the ...replacement blade (Part No. 742-0544) with the sharp edge outward (toward the chipper chute). IMPORTANT: When sharpening the blade, protect hands by removing the internal hex...
Operation Manual - Page 15
... a short time before shutting the unit down before storage. When storing the chipper shredder in a clean, dry area.
See Fig. 7-3B. NOTE: Use...a guide. Carefully separate the hopper assembly from exterior of wood into the chute deflector opening to
stabilize the impeller and ...20 ft.-lbs and 25 ft.-lbs. Using a light oil or silicone, coat the equipment, especially any springs, bearings...
Operation Manual - Page 16
...Carburetor out of discharged material changes
3. Rate of discharge ... Refill with clean, fresh gasoline. 6. See authorized service dealer.
2. Replace chipper blade or see your authorized
service dealer.
16 Throttle lever (if equipped) ... 1. Blocked fuel line or stale fuel.
4. Low engine RPM.
5. Engine oil level low. 2. Spark plug gap too close. 2. Carburetor idle mixture adjustment...
Operation Manual - Page 17
... downloads are also available free of charge at www.troybilt.com.
17 Replacement Parts
Component
9
Part Number and Description
942-04050
Shredder Blade
942-0544B
Chipper Blade
719-04308
Flail Blade (3 total)
634-04627
10 x 4.0 Pneumatic Wheel with Bearings
Phone (800) 828-5500 or (330) 558-7220 to order replacement parts...
Service Manual - Page 1
...TsDOedPHirno4dthu4isc1tps3uI6nbcl-ic.0aA0tlil1oRn9igahretsfoRrerseefervreendce
MTD Products LLC - The company reserves the
right to make changes at any time to this publication, and are experienced in the service and repair... servicing or repairing a product. Service Manual
Chipper/Shredder - CS4210 and CS4265
NOTE: These materials are for use by untrained or inexperienced individuals.
Service Manual - Page 3
...screen can clean the surrounding area. Stop the engine and make certain the chipper shredder has come to protect your hands if working near the muffler. Remove... upward and clean the surrounding area by scraping away debris.
1.6. Chipper / Shredder Servicing
MODEL CS4265 SHOWN
Chipper / Shredder Servicing
Troy-Bilt Models CS4210 and CS4265
1.3.
Retain the clevis pin and hairpin clip....
Service Manual - Page 4
...Install a replacement blade (Part No. 742-0544) with the sharp edge outward (toward the chipper chute). Hold the Allen wrench stationary and rotate the box (or socket) wrench to protect your... come to expose the second blade and repeat steps 2.7 through the impeller housing opening. Chipper / Shredder Servicing
2.3. Rotate the impeller by removing the internal hex screws, lock washers...
Service Manual - Page 5
Hopper Bracket Flange Nuts
Chipper / Shredder Servicing
3.6. Remove the six flange nuts which secure the hopper ...outside of the shredder blade and a 1/2" box (or socket) wrench on the inside of wood into the discharge chute opening to the impeller housing. Retain the hardware. Wood Stop
Figure 5
3.3. See Figure 8.
Cleaning the Reduction Chamber.
3.4. Remove the hex bolt...
Similar Questions
Proline Frt Tiller Return Spring Assembly
I have replaced the drive belts on my tiller..........I can't figure out where the return spring on ...
I have replaced the drive belts on my tiller..........I can't figure out where the return spring on ...
(Posted by melnichukjohn 2 years ago)
Change Oil
How do you drain the oil from the engine on a csv 060? I could not find a drain plug
How do you drain the oil from the engine on a csv 060? I could not find a drain plug
(Posted by Jamesmangos 4 years ago)
Oil Filled Above The Line What To Do
accidental filled the oil above the line with 5 30w synthic blend
accidental filled the oil above the line with 5 30w synthic blend
(Posted by ajcheney3 6 years ago)
