Home » Troy-Bilt » Lawn Mowers » Troy-Bilt TB554

Troy-Bilt TB554 Support Question

Find answers below for this question about Troy-Bilt TB554.
Need a Troy-Bilt TB554 manual? We have 1 online manual for this item!

Troy-Bilt Overview Questions Manuals Reviews Videos Research

Question posted by Anonymous-120520 on September 13th, 2013

How To Replace The Starter Rope On A Tb 146ec

My starter rope broke and I need to replace it.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Troy-Bilt TB554 Manual Pages

Operation Manual - Page 1

... INJURY. Printed In USA TROY-BILT LLC, P.O. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual Lawn Edger -

Operation Manual - Page 3

...clothes which could endanger the personal safety and/or property of age to edge lawn. a. As with these instructions may result in the operator's manual. Only ... in handling gasoline. Engine Exhaust, some of its entirety before operating it for ordering replacement parts. 2. Preparation 1. Never operate this manual in serious injury or death. Always...

Operation Manual - Page 4

...damaged or excessively worn cutting blade. 11. Do not use care and good judgment. Replace gasoline cap and tighten securely. m. Failure to another area. Engine exhaust contains carbon monoxide... until fueling is running. i. Doing so, makes the machine unsafe and may run into the lawn edger. 4 Section 2 - Never attempt to power equipment such as on a water heater,...

Operation Manual - Page 5

... a hot muffler. 6. Disconnect the spark plug wire and ground against the engine. Lawn edger blades are working condition. 6. Keep all mechanical and safety systems are sharp and... blade and engine mounting bolts at frequent intervals for damage (e.g., bent, cracked, worn) Replace blade with safety devices. Environmental Protection Agency (EPA), this manual. Spark Arrestor WARNING! ...

Operation Manual - Page 7

...'s Manual † If Equipped • One Edger Operator's Manual • One Trenching Blade Kit† • One Bottle Engine Oil • One Wing Knob and Rope Guide NOTE: This machine is observed from the inside to outside. NOTE: Reference to right or left side of the blade control as shown in...

Operation Manual - Page 8

...in the manual bag. Use extreme caution when handling gasoline. Upper Handle Figure 3-3 2. WARNING! Starter Rope 1. Never fuel the machine indoors or while the engine is depressed against the upper handle. ... found on the handle to the upper handle. Gently pull the starter rope out of the rope guide. NOTE: The starter rope will not pull out of the engine unless the blade control (...

Operation Manual - Page 9

Use it to control the depth of the cut . Recoil Starter The recoil starter is used to start a cold engine, but do not use it ... the edger while edging grass along a curb. Controls and Features 4 Blade Control Blade Depth Control Lever Recoil Starter Primer Curb Height Adjustment Lever Bevel Adjustment Lever WARNING! Be familiar with all engine controls, refer to vary the...

Operation Manual - Page 10

...primer three times. WARNING! With your right hand, grasp recoil starter handle and pull rope slowly until engine cranks. See Figure 5-1. Keep the area clear...sure to start the edger's engine, proceed as follows: 1. Keeping a firm grip on the starter cord handle, let the rope rewind slowly. Stopping The Engine To stop the edger's engine, release the blade control. The blade...

Operation Manual - Page 12

... the hex bolt head from spinning and the other to remove the flange nut) to Figure 6-1. Flat Washer Flange Nut Edger Blade Figure 6-1 2. Install the replacement edger blade and the flange nut removed earlier. Use a torque wrench to tighten the flange nut to the Engine Operator's Manual packed with light oil...

Operation Manual - Page 13

...again making sure to pivot slightly out from around the engine flywheel pulley. See Figure 7-2. 6. To replace the belt, proceed as follows: 1. Reinstall the spindle sheaves belt guard with the self tapping screws... engine flywheel pulley prior to the blade plate assembly. Refer to wear and should be replaced if any signs of the frame. The edger drive belt is seated into the bottom ...

Operation Manual - Page 14

... the previous page. 2. Off-Season Storage Observe the following when preparing the edger for engine manufacturers's storage instructions. 3. Clean and lubricate the edger thoroughly as lawn fertilizer. 5. NOTE: When storing any springs and bearings with a light oil or silicone spray. Coat the edger, especially any type of power equipment in a dry...

Operation Manual - Page 15

... Idles poorly Excessive Vibration Drive-belt Slips Cause 1. Refer to the Engine Operator's Manual. 1. Drain fuel tank. Refer to the Engine Operator's Manual. 1. Replace drive belt. 15 Engine needs to the Engine Operator's Manual 2. Engine oil level low. 2. Spark plug fouled, faulty, or gap too wide. 2. Refer to be primed. 3. Push primer...

Operation Manual - Page 17

... Screw, 1⁄4-20 Screw, 3⁄8-16 Hex Screw, 5⁄16-12 Hex Screw 5⁄16-18 Hex Screw, 5⁄8-18 Carriage Bolt, 5⁄16-18 Rope Guide (Eye Bolt) Hex Screw, 5⁄16-18 Axle Shaft .50x6.65 Frame Spacer .50x9.25 Lock Flange Nut, 5⁄16-18 Flange Nut 3⁄...

Operation Manual - Page 18

... or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for a period of two (2) years commencing on the date of..., seats, snow thrower skid shoes, friction wheels, shave plates, auger spiral rubber and tires. Replacement parts that are not limited to items such as lubricants, filters, blade sharpening, tune-ups, ...