Troy-Bilt TB554 Support Question
Troy-Bilt TB554 Support Question
Find answers below for this question about Troy-Bilt TB554.Need a Troy-Bilt TB554 manual? We have 1 online manual for this item!
Current Answers
Related Troy-Bilt TB554 Manual Pages
Operation Manual - Page 1
... 3, 2013) Printed In USA
TROY-BILT LLC, P.O.
Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Lawn Edger -
Operation Manual - Page 2
... times. If applicable, the power testing information used to establish the power rating of the engine equipped on this machine can locate the model plate...in this entire manual prior to the retailer or dealer without incurring obligation.
Please refer to the engine manufacturer's Owner's/Operator's Manual, packed separately with regards to the right. Table of Contents
Safe ...
Operation Manual - Page 3
...engine is a precision piece of power equipment, not a plaything. This machine is running, except where specifically recommended in operation. Therefore, exercise extreme caution at least 75 feet from lawn...ricochet can occur when gasoline is to use of yourself and others. Always wear safety... future and regular reference and for any type of power equipment, carelessness or error on...
Operation Manual - Page 4
... operate machine in personal injury.
19. Only use care and good judgment. Failure to no more...oil or fuel spillage and remove any fuel soaked debris. Shut the engine off if a child enters the area.
3. Stay alert for small children.
4. Stop the engine, disconnect spark plug wire and ground against the engine... run into the lawn edger.
4
Section 2 - Always stop engine when edging or ...
Operation Manual - Page 5
..., brushcovered or grass-covered land unless the engine's exhaust system is used gas, oil, etc.. The governor controls the maximum safe operating speed of age to operate this machine. Failure to do not meet the original equipment specifications may lead to prevent unintended starting and operating the lawn edger.
8. Spark Arrestor
WARNING! In the...
Operation Manual - Page 6
... symbols that may appear on the machine before attempting to assemble and operate
WARNING-
Stop machine if anyone enters the area. Your Responsibility-Restrict the use of this power machine to persons who read, understand and follow all instructions in this machine. Important Safe Operation Practices SAVE THESE INSTRUCTIONS!
6
Section 2 - ROTATING...
Operation Manual - Page 7
... Figure 3-2. 3. NOTE: Reference to outside.
Hook the Z end of Carton
• One Edger • One Engine Operator's Manual † If Equipped
• One Edger Operator's Manual • One Trenching Blade Kit†
• One Bottle Engine Oil • One Wing Knob and Rope Guide
NOTE: This machine is observed from the
inside to...
Operation Manual - Page 8
... Upper Handle
Figure 3-3
2.
Using the wing knob, secure but do not tighten the rope guide to the upper handle.
Never fuel the machine indoors or while the engine is pulled. Extinguish cigarettes, ...shown in Figure 3-4.
2 3
1 4
Figure 3-5
Set-Up
Gas & Oil Fill-Up
Service the engine with gas and oil as shown in Figure 3-3. Read Instructions carefully. Securing Control Cable
WARNING: ...
Operation Manual - Page 9
... depth of the edger.
Blade Control
Located on the rear portion of the cut . Blade Depth Control Lever
The blade depth control lever is used to restart a warm engine after a short shutdown.
It is located on the front, left portion of the upper handle. Bevel Adjustment Lever
The bevel adjustment lever is...
Operation Manual - Page 10
... to the START position in the adjacent (top) notch.
2. Stopping The Engine
To stop the edger's engine, release the blade control.
Several passes may throw objects and cause personal injury...best results, proceed slowly along the area to be edged, making sure to start the edger's engine, proceed as follows:
1. Push the primer three times. This blade control mechanism is moved, ...
Operation Manual - Page 11
...You can be edged along a curb. Disconnect the spark plug wire and ground against the engine before performing the following steps. Beveling
In order to achieve a bevelled edge, set the ...beveling. Edger Blade Flat Washer
Flange Nut
Figure 5-5
2. See Figure 5-5.
3. Operation
11 Use two wrenches (one of five positions to lock the wheel in position for landscape lighting. ...
Operation Manual - Page 12
...Figure 6-2.
Also if the wheels are removed for a detailed description of the wheel with light oil. and 50 foot-lbs. Maintenance & Adjustments
6
Maintenance
WARNING! Refer to remove the edger ...blade but retain the flange
nut. 3. Engine
Refer to the Engine Operator's Manual packed with your hands when working around the edger blade.
1. Use a torque wrench to tighten the flange ...
Operation Manual - Page 13
...the spindle sheaves belt guard by removing the two self-tapping screws which secure it onto the engine flywheel pulley. See Figure 7-2.
6. Make certain that it is riding smoothly on the spindle sheaves... flat side of the belt is not pinched between them. WARNING! Working from around the engine flywheel pulley. Reinstall the spindle sheaves belt guard with the self tapping screws removed earlier....
Operation Manual - Page 14
... page.
2. Off-Season Storage
Observe the following when preparing the edger for engine manufacturers's storage instructions.
3. Coat the edger blade with a light oil or silicone spray. Do not store next to prevent rusting and corrosion.
4. Coat the edger, especially any type of power equipment in a dry, clean area. Service Store the edger in...
Operation Manual - Page 15
.... Fill tank with proper oil. 2. Stale fuel in gas cap plugged. 4. Blade spindle bent or damaged. 1. Push primer bulb two or three times. 3. Drain gasoline and refill tank with clean, fresh
gasoline. 3. Refer to the Engine Operator's Manual. 1. Refer to the Engine Operator's Manual. 1. Refer to start
Engine runs erratic
Engine Overheats Occasional skips (hesitates...
Operation Manual - Page 18
..., without limitation, expenses incurred for substitute or replacement lawn care services or for rental expenses to temporarily replace ...MTD Products Limited with respect to new merchandise purchased and used in Canada and/ or its territories and possessions (...or oral, except as : grass collectors and mulch kits. The engine or component parts thereof. e. f. g.
No other than an ...
Similar Questions
Need New Motor Engine For Troy Bitl Riding Lawn Mower 15.5
(Posted by janicesutton60 2 years ago)
Can't Start Engine
new spark plug, new gas. still won't start. what else could it be?
new spark plug, new gas. still won't start. what else could it be?
(Posted by gls0480 2 years ago)
Lawn Mower
What kind of oil do I use in my troy bilt 140cc 110b push behind mower is it ok to use 10w30
What kind of oil do I use in my troy bilt 140cc 110b push behind mower is it ok to use 10w30
(Posted by sgilbert491974 9 years ago)