Troy-Bilt TB554 Support Question
Troy-Bilt TB554 Support Question
Find answers below for this question about Troy-Bilt TB554.Need a Troy-Bilt TB554 manual? We have 1 online manual for this item!
Question posted by jeannesmith on July 24th, 2022
Oil Check
Do you check the oil by dipping the stick down ok only or do you screw it in place? TB 554 edger
Current Answers
Related Troy-Bilt TB554 Manual Pages
Operation Manual - Page 1
...
Form No. 769-08749A (January 3, 2013) Model 554
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Lawn Edger - FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY...
Operation Manual - Page 2
... machine.
Please refer to the engine manufacturer's Owner's/Operator's Manual, packed separately with the machine, its features and operation.
It instructs you for purchasing an Edger manufactured by standing at the operator's position and looking down at the time of the engine equipped on the equipment and record the information in...
Operation Manual - Page 3
...lawn. Failure to observe the following safety instructions could be tripped over should be allowed to be trained and supervised by the blade.
Keep this manual in a safe place..., bystanders, helpers and pets at all stones, sticks, wire, bones, toys and other reproductive harm.... exercise extreme caution at least 75 feet from lawn edger while it for ordering replacement parts.
2. Never...
Operation Manual - Page 4
...another area. Always place containers on the ground. Remove gas-powered equipment from the truck or trailer and refuel it on the ground away from your footing and keep lawn edger free of your vision...behind and down for assistance or the name of grass, leaves, or other debris build-up oil or fuel spillage and remove any fuel soaked debris. Contact with a damaged or excessively worn ...
Operation Manual - Page 5
...For safety protection, frequently check all nuts, bolts, and screws tight to operate this machine. Section 2 - Disconnect the spark plug wire and ground against the engine. Lawn edger blades are working order by..., repairing, or inspecting, make a wheel adjustment while the engine is used gas, oil, etc.. Failure to make certain the blade and all mechanical and safety systems are...
Operation Manual - Page 7
... your machine. See Figure 3-1.
Hook the Z end of the brake cable into place. NOTE: Reference to outside.
To make it easier to attach the Z-fitting, temporarily remove
the left hand side of the edger is shipped WITHOUT GASOLINE or OIL. Control Cable Z-Fitting
Unwrap the control cable from the engine and route it...
Operation Manual - Page 8
...rope guide and wing knob found inside the snap fitting into place. WARNING! Use extreme caution when handling gasoline. Assembly & Set...Upper Handle
Figure 3-3
2. Starter Rope
1.
WARNING! The edger blade WILL rotate when the starter rope is extremely flammable and...1 4
Figure 3-5
Set-Up
Gas & Oil Fill-Up
Service the engine with gas and oil as shown in the Engine Operator's Manual packaged...
Operation Manual - Page 9
.... Know how to stop the machine and disengage it to vary the angle of the edger blade between one of the upper handle.
Curb Height Adjustment Lever
The curb height adjustment lever...order to start a cold engine, but do not use it quickly. When placed in an applicable notch, it aids in stabilizing the edger while edging grass along a curb. Bevel Adjustment Lever
The bevel adjustment lever ...
Operation Manual - Page 10
...depth control lever
is a safety device.
The blade can strike the supporting surface, resulting in place. Move the blade depth control lever back to but not touching the edge of cut ....on a hard surface and the blade is over the area to be edged before proceeding to start the edger's engine, proceed as follows:
1. To begin edging, proceed as follows:
1. notch. Figure 5-1
Figure...
Operation Manual - Page 11
... wheel in position. NOTE: Make certain that the drive belt is not pinched between 37 foot-lbs. Use two wrenches (one of five positions to place the edger blade in position for landscape lighting. See Figure 5-4. Disconnect the spark plug wire and ground against the engine before performing the following steps.
Operation Manual - Page 12
... the wheels and bearings at least once a season. Flat Washer
Flange Nut
Edger Blade
Figure 6-1 2. Maintenance & Adjustments
6
Maintenance
WARNING! Refer to remove the edger blade. Also if the wheels are removed for a detailed description of the cover plate. Simply apply oil at least once a season. NOTE: Make certain that the drive belt is...
Operation Manual - Page 13
... removing the two self-tapping screws which secure it onto the engine flywheel pulley. Make certain that the drive belt is seated into the bottom pulley. Never operate the edger without the spindle sheaves belt .... With your other hand, carefully reach under the rear of the edger and remove the belt from the front of the edger, place the belt onto the spindle sheaves, route it back onto the two...
Operation Manual - Page 14
... storage:
1. Service Clean and lubricate the edger thoroughly as lawn fertilizer.
5. Store the edger in an poorly ventilated or metal storage shed, care should be taken to the Engine Operator's Manual packed separately with a light oil or silicone spray. Refer to rustproof the equipment.
14
Section 7-
Coat the edger, especially any type of power equipment...
Operation Manual - Page 15
... wire. 2. Refill with clean, fresh gasoline. 4. Refer to the Engine Operator's Manual. 1. Replace edger blade. 2. Engine needs to the Engine Operator's Manual. 1. Spark plug wire disconnected.
6. Water or... two or three times. 3. Drain gasoline and refill tank with proper oil. 2. Adjust gap. Dirty air cleaner. 1. Edger blade bent or damaged. 2.
Clean, adjust gap or replace spark plug...
Operation Manual - Page 17
...
34 734-1268
Description Curb Height Adjustment Lever Curb Height Adjuster Plate Blade Plate Assembly Screw 3⁄8-24 Screw 3⁄8-16 Hex Screw, 5⁄16-18 Self-tapping Screw, 1⁄4-20 Screw, 3⁄8-16 Hex Screw, 5⁄16-12 Hex Screw 5⁄16-18 Hex Screw, 5⁄8-18 Carriage Bolt, 5⁄16-18 Rope Guide (Eye Bolt) Hex...
Operation Manual - Page 18
... of other than an authorized service dealer. Troy-Bilt warrants attachments for this warranty. Check your local authorized service dealer. d.
IMPORTANT: Owner must present Original Proof of the ...consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for a particular purpose, applies after the applicable period of...
Similar Questions
Need New Motor Engine For Troy Bitl Riding Lawn Mower 15.5
(Posted by janicesutton60 2 years ago)
Can't Start Engine
new spark plug, new gas. still won't start. what else could it be?
new spark plug, new gas. still won't start. what else could it be?
(Posted by gls0480 2 years ago)
Lawn Mower
What kind of oil do I use in my troy bilt 140cc 110b push behind mower is it ok to use 10w30
What kind of oil do I use in my troy bilt 140cc 110b push behind mower is it ok to use 10w30
(Posted by sgilbert491974 9 years ago)