Home » Troy-Bilt » Lawn & Garden » Troy-Bilt TB2044

Troy-Bilt TB2044 Support Question

Find answers below for this question about Troy-Bilt TB2044.
Need a Troy-Bilt TB2044 manual? We have 1 online manual for this item!

Troy-Bilt Overview Questions Manuals Reviews Videos Research

Question posted by psalm91113 on October 2nd, 2017

Help

hiw to replace a head on a troybuilt weedeater tb2044xp

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on October 2nd, 2017 4:58 PM

This answer was accepted by the poster of the original question.

Odin

Member since:
April 10th, 2010

Points: 41,236,680

1,100
points

See https://www.youtube.com/watch?v=Slcz-Q3SBHw.

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Related Troy-Bilt TB2044 Manual Pages

Operation Manual - Page 1

... MTD SOUTHWEST INC, All Rights Reserved. 11/12 When servicing, use only identical replacement parts. 769-08520 / 01 All information, illustrations, and specifications in Canada. Additional... by an authorized and approved service dealer. Operator's Manual Electric Start Capable 2-Cycle Trimmer TB2044 XP TABLE OF CONTENTS Service 1 Safety 2 Know Your Unit 5 Specifications 5 Assembly ...

Operation Manual - Page 2

...the states of California to cause cancer and birth defects or other objects that it requires replacement, ask your careful attention and understanding. SPARK ARRESTOR NOTE NOTE: For users on forest brush.... • Never operate the unit without the fuel cap securely in serious injury to the head, hands and feet. • Carefully inspect the area before using the unit, all adjustments ...

Operation Manual - Page 3

...a height to the unit, and void the warranty. • Keep the unit clean. The cutting head remains stationary when the engine is dusty. • Wear heavy long pants, boots, gloves and a...disconnect the spark plug for maintenance or repair. • Use only original equipment manufacturer (OEM) replacement parts and accessories for the cause of the shield. • This unit has a clutch....

Operation Manual - Page 5

... at the time of printing. Spark Plug Muffler Throttle Lockout ASSEMBLY TOOLS REQUIRED: • #2 Phillips screwdriver • 3/8" Socket Handle On/Off Switch Cutting Head Shaft Housing Cutting Head Shield Coupler Shaft Grip Throttle Control Choke Lever Starter Rope Grip Air Filter Cover Fuel Cap Line Cutting Blade Primer Bulb SPECIFICATIONS* Engine Type...

Operation Manual - Page 6

...THE HANDLE Installing the Handle 1. Insert the bolt into the cutting head shield until the cutting head shield is secure. Tighten the bolt with a 3/8" socket until the handle is...do not tighten the bolt completely. 3. Tighten the bolt with this unit. 1. The bolt hole in the cutting head shield with a 3/8" socket (Fig. 2). 2. Shaft Grip Minimum 6 in place. Place it a minimum of ...

Operation Manual - Page 8

... UNIT. Always use a 2-cycle oil designed for specific gasoline and oil mixing ratios. CAUTION: For proper engine operation and maximum reliability, pay strict attention to help inhibit corrosion and minimize gum deposits. Move the unit at a distance from the area. Use a separate fuel can make fuel and oil separate, forming acids...

Operation Manual - Page 11

...1.5 inches (38 mm) of injury when operating this unit. • Stand in the cutting head shield will make the unit overheat. Fig. 13 11 Line release becomes more line, lightly tap...the right hand. Bump Knob Fig. 12 TIPS FOR BEST TRIMMING RESULTS • Keep the cutting head parallel to right whenever possible. Fig. 11 ADJUSTING THE TRIMMING LINE LENGTH This unit is released. Keep...

Operation Manual - Page 12

...the line until the ends are unsure about 5 inches (12.7 cm) protrude from the cutting head. Always allow the unit to the unit. These procedures should also be performed by an MTD... Specifications section. DO NOT push the bump knob down while winding the line. NOTE: Maintenance, replacement, or repair of new trimming line. 3. If necessary, remove any seasonal tune-up. MAINTENANCE ...

Operation Manual - Page 13

...is not covered by unscrewing the cover screw (Fig. 21). 2. Remove the air filter from the cutting head. 1. Reinstall the air filter in detergent and water. Wash the air filter in the air filter housing... (Fig. 21). Tab 2. Failure to the engine. Insert the hooks on the cutting head (Fig. 16). Swing the air filter cover to clean the inner reel, outer spool and spool ...

Operation Manual - Page 14

...throttle control and let the engine idle. Grasp the spark plug boot firmly and pull it with a replacement part #753-06193, a Champion RDJ7J or an equivalent spark plug. 4. Grit in . (0.635... Speed Screw Fig. 23 MAINTAINING THE SPARK PLUG 1. If the engine is cracked, fouled or dirty, replace it from the cylinder head with a 5/8-inch socket, turning it to : 110-120 in . (0.635 mm) (Fig. 24...

Operation Manual - Page 15

.... Reinstall the fuel cap. 2. This ensures that contain aromatic oils such as pine and lemon, and solvents such as kerosene, can damage plastic. Repair or replace damaged parts and tighten loose screws, nuts or bolts. Short-term Storage (1-2 weeks) 1. CLEANING AND STORAGE CLEANING WARNING: To avoid serious personal injury, always stop...

Operation Manual - Page 16

... with grass The air filter is dirty Drain the fuel tank and add fresh, properly mixed fuel Stop the engine and clean the cutting head Clean or replace the air filter THE ENGINE LACKS POWER OR STALLS The fuel is old (over 30 days) and/or improperly mixed The air filter is...

Operation Manual - Page 20

...be greater than the original purchaser, original lessee or the person for rental expenses to temporarily replace a warranted product. (Some states do not allow limitations on the date of any product previously...Product without limitation, expenses incurred for substitute or replacement lawn care services, for transportation or for related expenses, or for whom it was purchased as a ...