Troy-Bilt Storm 2410 Support Question
Troy-Bilt Storm 2410 Support Question
Find answers below for this question about Troy-Bilt Storm 2410.Need a Troy-Bilt Storm 2410 manual? We have 1 online manual for this item!
Question posted by tconway on December 15th, 2020
Mice Built Nest Around Throttle Assembly. There Is No Spark. Could Coil Ground B
how do I get to coi
Current Answers
Answer #1: Posted by INIMITABLE on December 17th, 2020 3:44 AM
INIMITABLE
Member since:
April 3rd, 2020 Points: 2,084,120
Member since:
April 3rd, 2020 Points: 2,084,120
If you still don't have spark, you most likely need a coil. Their not hard to change. You have to pull off the pull starter shroud and it should be easy to access. You may want to check it with an ohm meter, also for an open, to verify that its bad.
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers
-INIMITABLE
Related Troy-Bilt Storm 2410 Manual Pages
Operation Manual - Page 1
FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. Storm 2410, 2620, 2840 & 3090XP
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
BOX 361131 CLEVELAND, OHIO ...
Operation Manual - Page 2
... carefully follow the recommended safety practices at the rear of Contents
Safe Operation Practices 3 Assembly & Set-Up 7 Controls 13 Operation 16 Maintenance & Adjustment 17
Service 20 Troubleshooting...phone a authorized Troy-Bilt service dealer or contact us on this product or have difficulty assembling this page.
This information will be found on the web at www.troybilt.com &#...
Operation Manual - Page 3
...assemble and operate. Know how to avoid slipping or falling, especially when operating in this machine without wearing adequate winter outer garments. Never allow adults to the safe operation practices in reverse. Exercise caution to stop the machine and disengage them quickly.
3. Use a grounded... 65
WARNING! DANGER: This machine was built to cause cancer and birth defects or ...
Operation Manual - Page 4
... on the ground away from a
leave the operating position (behind and use care
j. Never direct discharge at least two minutes before filling.
17.
Never put hands or feet near rotating parts, in both directions
21. Always use a nozzle lock-open flame, spark or pilot light
14. Do not unclog chute assembly while engine...
Operation Manual - Page 5
...Useful Life of seven (7) years, or 60 hours of operation.
Disconnect the spark plug wire and ground against the engine to operate at frequent intervals to improper performance and compromise safety...According to clear snow from machine and prevent freeze up of auger/impeller.
10. Spark Arrestor
Warning! Other states may have stopped rotating.
3. Box 361131 Cleveland, Ohio 44136...
Operation Manual - Page 6
.... Contact with the rotating parts can cause serious personal injury.
Your Responsibility-Restrict the use the engine's electric starter in the manual(s) before attempting to assemble and operate
WARNING- Symbol
Description
READ THE OPERATOR'S MANUAL(S) Read, understand, and follow all instructions in the rain
WARNING- Engine exhaust contains carbon monoxide, an...
Operation Manual - Page 7
...-6 position. 2. Secure the handle by tightening the plastic knob located on both cables are aligned with roller guides before pivoting the handle upward.
Figure 3-2
Chute Assembly (Model 2410)
1. Figure 3-1 NOTE: Make certain the cables are for packaging purposes only. See Fig. 3-2. 3. Observe the lower rear area of the snow thrower to be...
Operation Manual - Page 8
...hairpin
holes in the rod pointing upward. Close the flange keepers to secure the chute assembly to Chute Bracket Adjustment on Page 19.
8
Section 3-
Chute Control Head
Chute Support Bracket
...Chute
Chute Base
Figure 3-4
Figure 3-6
Chute Directional Control (Model 2410)
2. Insert chute control rod into place when properly secure. clip from the end of...
Operation Manual - Page 9
... Input
Top View
while inserting the rod with wing nut at the one o'clock position so that the silver indicator arrow on the pinion gear.
Assembly & Set-Up
9
NOTE: The joystick will fit snuggly into the pinion gear below the control panel faces upward. Insert the chute control rod into the...
Operation Manual - Page 10
... be to the top of the engine. See Fig. 3-14. cable guide on top of the auger housing with the hole in your snow thrower. Assembly & Set-Up
Figure 3-15 See Fig. 3-13. Cut the cable tie before operating the snow thrower.
Figure 3-14
Figure 3-12
8. Store them in the chute...
Operation Manual - Page 11
... the tire pressure before retightening the wing knob. Refer to the tire side wall for shipping purposes.
Chute Assembly (Models 2410 and 2620)
NOTE: The upper chute on models 2840 and 3090XP is against the ground to be maintained at the factory for tire manufacturer's recommended psi and deflate (or inflate) the tires...
Operation Manual - Page 12
... the auger to the operator's position and shut off the engine. With the throttle control in the FAST (rabbit) position and the auger control in the disengaged ... position (behind the snow thrower), engage the auger.
4. If the auger shows ANY signs of the machine.
6. Assembly & Set-Up In a well-ventilated area, start the snow thrower engine. Prior to stop before releasing the auger...
Operation Manual - Page 13
...below and illustrated in the right side of the handle panel and is used to determine ground speed and direction of the handle panel and is automatically turned on when the engine is... started.
13
Adjust downward when operating on surface conditions. Chute Assembly
Snow drawn into the auger housing.
One (1) is the slower and two (2) is the fastest...
Operation Manual - Page 15
... housing, reinsert the key and start the snow thrower's engine.
Controls and Features
15
Should snow and ice become lodged in and near the chute assembly.
5. The left and right wheel steering trigger controls are familiar with a mounting clip. Section 4 - Steering Trigger Controls (if so equipped)
Chute Clean-Out Tool
Warning...
Operation Manual - Page 16
... controls)
With the drive control engaged, squeeze the right steering trigger control to the Engine Operator's Manual packed with your snow thrower's warranty.
With the throttle control in the Fast (rabbit) position, move the switch found on starting and stopping the engine. Squeeze the left steering trigger control to turn it...
Operation Manual - Page 18
... of the above to verify proper adjustment has been achieved. Shut off the engine as instructed in the cable. 4. Pivot the bracket downward to the Assembly and Set-up slack in the separate engine manual.
2. Auger Shaft
At least once a season, remove the shear pins from the auger shaft. Spray lubricant...
Operation Manual - Page 19
...2840, y 3090XP)
To adjust the chute control rod, proceed as instructed earlier in the chute rotation assembly. See Fig. 6-7. If storing the snow thrower in a clean, dry area. 4.
Figure 6-6
3....as follows:
1. Remove the cotter pin from the engine. 2. Chute Bracket Adjustment (Model 2410)
If the spiral at the bottom of the chute directional control is empty and it stops...
Operation Manual - Page 23
...screws which secures the hex shaft 7. Figure 7-9
6. NOTE: When reassembling the friction wheel assembly,
make sure that the rubber ring is in place in the bearing housing. Repeat this ...friction wheel's side plates together.
See Fig. 7-9.
8. If you 're replacing the friction wheel assembly as follows:
1. Carefully position the hex shaft downward and to damage the threads on the shaft....
Operation Manual - Page 24
... tool or a stick.
2. Stop engine immediately and disconnect spark plug wire. Drive control cable in the Assembly section. Foreign object lodged in ignition on engine. 7. Shear pin(s) sheared. ... to a three-prong 120-volt, grounded, AC outlet.
1. Connect one end of the extension cord to the
electric starter outlet and the other end to spark plug. 3. Be certain
vent hole is...
Operation Manual - Page 25
... 684-04159 935-04054
Auger Drive Belt (Storm 2410 & Storm 2620 with 15" tires) Auger Drive Belt (Storm 2840 & 3090XP & Storm 2620 with 16" tires) Wheel Drive Belt (Storm 2410 & Storm 2620 with 15" tires) Wheel Drive Belt (Storm 2840 & 3090XP & Storm 2620 with 16" tires)
Friction Wheel Assembly (Storm 2410, 2620 & 2840) Friction Wheel Assembly (Storm 3090XP) Friction Wheel Rubber
725-1629 725...
Similar Questions
Troy Built Storm 2410
I replaced the carburetor and I have 2 silver sleeves left that I don't know where they go, one is s...
I replaced the carburetor and I have 2 silver sleeves left that I don't know where they go, one is s...
(Posted by brucepieper1 3 years ago)
Spark Plug Gap Set
what should the spark plug for. my tb625 ec troy built weed eater be gapped at?
what should the spark plug for. my tb625 ec troy built weed eater be gapped at?
(Posted by ginac566 6 years ago)
Tb2044xp Coil Clearance
What is the distance between the coil and flywheel on tb2044?My trimmer only runs good if I have spa...
What is the distance between the coil and flywheel on tb2044?My trimmer only runs good if I have spa...
(Posted by bjstrieff 10 years ago)