Home » Troy-Bilt » Lawn & Garden » Troy-Bilt Storm 2410

Troy-Bilt Storm 2410 Support Question

Find answers below for this question about Troy-Bilt Storm 2410.
Need a Troy-Bilt Storm 2410 manual? We have 1 online manual for this item!

Troy-Bilt Overview Questions Manuals Reviews Videos Research

Question posted by brucepieper1 on January 28th, 2021

Troy Built Storm 2410

I replaced the carburetor and I have 2 silver sleeves left that I don't know where they go, one is shorter than the other

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by waelsaidani1 on February 15th, 2021 6:21 PM

This answer was accepted by the poster of the original question.

waelsaidani1

Member since:
May 12th, 2013

Points: 19,501,797

1,100
points

Hello here is a video guide on what to do: https://www.youtube.com/watch?v=F3IL2w7XGjg

Related Troy-Bilt Storm 2410 Manual Pages

Operation Manual - Page 1

... RESULT IN PERSONAL INJURY. Printed In USA TROY-BILT LLC, P.O. Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual Two-Stage Snow Thrower - BOX 361131 CLEVELAND, OHIO 44136-0019 Form No. 769-06897 (May 17, 2011) Storm 2410, 2620, 2840 & 3090XP WARNING READ AND...

Operation Manual - Page 2

...-Up 7 Controls 13 Operation 16 Maintenance & Adjustment 17 Service 20 Troubleshooting 24 Replacement Parts 25 Attachments 26 Warranty Back Cover Record Product Information Before setting up ,...information available at all references to right and left side of product specifications for purchasing a Troy-Bilt Snow Thrower. Troy-Bilt's Customer Support telephone numbers, website address ...

Operation Manual - Page 3

... Use a grounded three-wire extension cord and receptacle for ordering replacement parts. 2. DANGER: This machine was built to State of the operator can cause serious personal injury. Never...Read, understand, and follow all instructions on slippery surfaces. 3. Keep this symbol. Know how to clear gravel or crushed rock surfaces. 5. Thrown objects can result in personal...

Operation Manual - Page 4

... 5 minutes before refueling. inch below bottom of the fuel tank or container opening at high transport speeds on a trailer with a missing or damaged chute assembly. Replace gasoline cap and tighten securely. If gasoline is extremely flammable and the vapors are not covered in this manual, use extreme care in handling gasoline...

Operation Manual - Page 5

...inside the discharge chute is available through your safety protection, frequently check all components and replace with the governor setting can result in any damage. 4. According to protect the ...a runaway engine and cause it should not be used on off-season storage. 12. Maintain or replace safety and instruction labels, as a water heater, furnace, clothes dryer etc. 11. Prior to...

Operation Manual - Page 7

... rear area of the snow thrower to be sure both the left and right sides of Carton • One Snow Thrower • One Snow Thrower Operator's Manual • One Engine Manual • Two Replacement Auger Shear Pins • One Chute Assembly (Model 2410) • One Product Registration Card • One Chute Control Rod...

Operation Manual - Page 8

... pin, wing nut and hex screw from chute control head. Chute Control Head Chute Support Bracket Chute Chute Base Figure 3-4 Figure 3-6 Chute Directional Control (Model 2410) 2. Insert the end of the chute directional control. Refer to the chute base.

Operation Manual - Page 9

... this time. Rotate the joystick to face forward. See "Top View" in the rod with wing nut at the one o'clock position so that the silver indicator arrow on the pinion gear. See Fig. 3-11. NOTE: The hole is inserted all the way into the pinion gear. Install hex bolt previously...

Operation Manual - Page 10

7. NOTE: The second hole is fastened to the left of the chute control rod into the pinion gear if required. See Fig. 3-14. See Fig. 3-13. ...Figure 3-14 Figure 3-12 8. Chute Clean-Out Tool Figure 3-13 10 Section 3- Set-Up Shear Pins A pair of replacement auger shear pins and bow tie cotter pins are properly routed through the cable guide. Some models only have one cable to ...

Operation Manual - Page 11

...changing the angle of the chute assembly. 2. NOTE: If you operate this snow thrower on the left side of the chute assembly. Move skid shoes to operating the snow thrower. Retighten nuts and ...bolts securely. Figure 3-17 3. Assembly & Set-Up 11 Chute Assembly (Models 2410 and 2620) NOTE: The upper chute on the skid shoes. 3. See Fig. 3-17. Adjust them ...

Operation Manual - Page 14

...drive control also locks the auger control so that you can release the auger control (on the left handle. Release both controls to do so will remain engaged. Auger Control Standard Chute Directional Control ...on the right handle. The 2-way chute directional control is located on the left side of the dash panel. • To change the direction in increased wear on your machine's...

Operation Manual - Page 15

...4-Way Chute Directional Control (if so equipped) The 4-way chute directional control is located on the left side of the dash panel. • To change the angle/distance which snow is thrown, pivot... the joy-stick forward or backward. Never use your hands to the left. • To change the direction in the operator's position (behind handles until you are located on...

Operation Manual - Page 16

...the ON position. Squeeze the left steering trigger control to the spiral shaft with your snow thrower's warranty. Replacing Shear Pins The augers are secured to turn left handle. If the augers will... squeeze the auger control against the handle the snow thrower will not turn, check to replacing shear pins. To Steer (models equipped with steering trigger controls) With the drive control...

Operation Manual - Page 17

...Maintenance Engine Refer to Fig 7-3. 4. NOTE: When lubricating the hex shaft, be checked periodically and replaced when necessary. Remove the carriage bolts and hex nuts which attach it is out of carriage bolts are...oil on each side) and hex flange nuts. Standard Chute Directional Control (Model 2410) Once a season, lubricate the eye-bolt bushing and the spiral with a multipurpose automotive grease...

Operation Manual - Page 19

... and Set-up section for 30 days or longer, follow the storage instructions below. 1. Remove the cotter pin from the engine. 2. Chute Bracket Adjustment (Model 2410) If the spiral at the bottom of the engine and the snow thrower.

Operation Manual - Page 20

... the belt as follows: 4. Figure 7-2 20 Figure 7-4 b. Allow the engine to run until it rests on the front of fuel. a. Service 7 Belt Replacement Auger Belt To remove and replace your snow thrower's auger belt, proceed as follows. Carefully pivot the snow thrower up and forward so that it is out of the...

Operation Manual - Page 22

... removing four self-tapping screws which secure it is out of wear or cracking and replace if necessary: 1. See Fig. 7-7. 8. Examine the friction wheel for information on the auger housing. 4. Stop Bolt Friction Wheel Removal (Models 2410, 2620 & 2840) If the snow thrower fails to drive with the drive control engaged, and...

Operation Manual - Page 25

... Chute Clean-out Tool 790-00120 790-00121 790-00118 790-00119 Shave Plate (Storm 2410) Shave Plate (Storm 2620) Shave Plate (Storm 2840) Shave Plate ((Storm 3090XP) 731-05632 Key 951-10292 Spark Plug Phone (800) 828-5500 to order replacement parts or a complete Parts Manual (have your full model number and serial number ready...

Operation Manual - Page 26

... attachments and accessories are available for information regarding compatibility, price and availability (have your Troy-Bilt snow thrower. Phone (800) 828-5500 for your full model number and serial number ready). Model Number Description 753-05762A OEM-390-679 490-241-0010 OEM-390-995 490-241-Y014 *Not compatible with Storm 2410.

Operation Manual - Page 28

... above as to be liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for whom it was purchased as mentioned above . Troy-Bilt LLC, P.O. KITCHENER, ON N2G 4J1; Service completed by someone other express warranty, whether written or oral, except as...