Troy-Bilt Storm 2410 Support Question
Troy-Bilt Storm 2410 Support Question
Find answers below for this question about Troy-Bilt Storm 2410.Need a Troy-Bilt Storm 2410 manual? We have 1 online manual for this item!
Question posted by dcook37366 on January 13th, 2023
Troy Bilt Snow Blower Engine (storm 2410)
I need to remove the shroud from the engine, and to do so I have to remove the choke knob. Can you tell me how to remove the choke knob?
Current Answers
Answer #1: Posted by Odin on January 14th, 2023 10:11 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
Look inside the small hole on the top of the knob to see if there is a small screw in there holding the knob on. If there is no screw, the the knob just prys off Just be carefull when you pry it off so you do not break anything. Even if it has a screw, you still may have to pry it off after removing the screw. Take a screwdriver and place kthe tip under th knkb and then gently twist the screwdriver to try to get it off. If that does not work, the gently push down on the screwdriver to pry it off. I
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Troy-Bilt Storm 2410 Manual Pages
Operation Manual - Page 1
...-0019
Form No. 769-06897 (May 17, 2011) Storm 2410, 2620, 2840 & 3090XP
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. Printed In USA
TROY-BILT LLC, P.O.
Safe Operation Practices • Set-Up...
Operation Manual - Page 2
...not be applicable to all models. All information in the provided area to the engine manufacturer's Owner's/Operator's Manual, packed separately with regards to provide excellent performance when...Customer Support
Please do so could result in this manual is responsible for purchasing a Troy-Bilt Snow Thrower. Please read this manual frequently to ensure your machine, for various models. ...
Operation Manual - Page 3
...to State of amputating fingers, hands, toes and feet and throwing foreign objects. Remove all controls and their proper operation. Thrown objects which ricochet can cause serious ...performing an adjustment or repair to protect your snow-throwing pattern to outdoor temperature before starting to operate this machine. Let engine and machine adjust to avoid discharge of yourself ...
Operation Manual - Page 4
.... Never bypass its operation. Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than from your snow-throwing pattern to a complete stop
k.
Never remove gas cap or add fuel while the engine is felt, then pull rapidly.
Do not overload machine capacity by attempting to another area. Move machine...
Operation Manual - Page 5
...Storage
1. Never tamper with spark plug removed.
14. Before cleaning, repairing, or inspecting machine disengage all components and replace with snow throwers. Wait until the auger/impeller ...if so equipped. To clear the chute:
1. Wait 10 seconds to clear snow from machine and prevent freeze up of the engine.
5. Always use your safety protection, frequently check all control levers and ...
Operation Manual - Page 7
... knob located on both cables are for packaging purposes only. Observe the lower rear area of the snow thrower to be sure
both the left and right sides of Carton
• One Snow Thrower • One Snow Thrower Operator's
Manual • One Engine Manual
• Two Replacement Auger Shear Pins • One Chute Assembly (Model 2410...
Operation Manual - Page 10
...See Fig. 3-12.
Store them in your snow thrower. Finish securing chute control head to chute... snow thrower. See Fig. 3-13. Refer to achieve further engagement of the auger housing with your snow... thrower's dash panel until the hole in the rod lines up with wing nut, clevis pin, and bow-tie cotter pin removed...toward the control panel until needed. Assembly & Set-Up
Figure 3-15 Chute Clean-...
Operation Manual - Page 11
... the skid shoes:
1. To do not exceed manufacturer's recommended psi. Remove the key from the engine and loosen the plastic knob found on models 2840 and 3090XP is against the ground to be cleared... chute assembly. Chute Assembly (Models 2410 and 2620)
NOTE: The upper chute on the left side of tire for shipping purposes.
The distance snow is thrown can easily pick up and...
Operation Manual - Page 12
... to provide more slack (or downward to verify proper
adjustment has been achieved.
12
Section 3- Assembly & Set-Up In a well-ventilated area, start the snow thrower engine. Confirm that the auger has completely stopped rotating and shows NO signs of the auger control as follows:
1. If the auger shows ANY signs of...
Operation Manual - Page 15
...tool to safely clean the chute assembly and chute opening:
1. Section 4 -
Remove the key.
3.
Caution: Operate the snow thrower in the operator's position (behind handles until you are located on the ... the left control to the rear of the auger housing with these controls. Stop the engine. Controls and Features
15 4-Way Chute Directional Control (if so equipped)
The 4-way ...
Operation Manual - Page 16
...rabbit) position, move the switch found on starting and stopping the engine. Release it off the snow thrower's engine and remove the key prior to replacing shear pins.
Squeeze the left steering.... See Fig. 5-1. Operation
5
Starting and Stopping the Engine
Refer to the Engine Operator's Manual packed with your snow thrower's warranty.
Select a speed appropriate for instructions on the...
Operation Manual - Page 17
.... Apply a light coating of carriage
bolts are subject to the snow thrower.
2.
Remove the carriage bolts and hex nuts which attach it . Reassemble new shave plate, making sure heads of engine oil (or 3-in -1 oil.
17 Tighten securely. Standard Chute Directional Control (Model 2410)
Once a season, lubricate the eye-bolt bushing and the spiral...
Operation Manual - Page 18
... If excessive slack is present in the drive cable or if the snow thrower's drive is in need of the shaft. Loosen the lower hex screw on adjusting the auger...Auger Shaft
At least once a season, remove the shear pins from the auger shaft. Proceed as instructed in need of the above to verify proper adjustment...the engine as follows:
1.
Loosen the hex nut on the shift cable index...
Operation Manual - Page 19
...2410)
If the spiral at the bottom of the chute directional control is empty and it stops due
to the Engine Operator's Manual for information on the chute rotation assembly.
2. Figure 6-6
3.
Run the engine...
1. NOTE: Refer to lack of the engine and the snow thrower. Remove the cotter pin from the engine. 2. Off-Season Storage
If the snow thrower will not be adjusted. Store in this...
Operation Manual - Page 20
.... 7-3.
1. Do not attempt to avoid unintended starting.
2. See Fig. 7-4. See Fig. 7-1. Loosen and remove the shoulder bolt which secure it. Remove the frame cover from the engine. Figure 7-1 3. Figure 7-2 20
Figure 7-4
b. Service
7
Belt Replacement
Auger Belt
To remove and replace your snow thrower's auger belt, proceed as follows.
Unhook the auger brake bracket spring from...
Operation Manual - Page 21
... belt, perform the Auger Control test on the auger housing.
5. c. Remove the plastic belt cover on the front of the snow thrower by running engine until it stops. Service
21 To prevent spillage, remove all fuel from the engine.
2.
Section 7 - 7. Roll the auger belt off engine pulley.
4.
Do not attempt to pour fuel from tank by...
Operation Manual - Page 22
... the problem, the friction wheel may need to be removed in order to replace the snow thrower's friction wheel rubber. Examine the friction wheel for signs of the snow thrower by removing four self-tapping screws which secure it to run until it . Allow the engine to the axle. Remove the frame cover from the underside of...
Operation Manual - Page 25
... 684-04159 935-04054
Auger Drive Belt (Storm 2410 & Storm 2620 with 15" tires) Auger Drive Belt (Storm 2840 & 3090XP & Storm 2620 with 16" tires) Wheel Drive Belt (Storm 2410 & Storm 2620 with 15" tires) Wheel Drive Belt (Storm 2840 & 3090XP & Storm 2620 with 16" tires)
Friction Wheel Assembly (Storm 2410, 2620 & 2840) Friction Wheel Assembly (Storm 3090XP) Friction Wheel Rubber
725-1629...
Operation Manual - Page 26
... (have your Troy-Bilt snow thrower. Phone (800) 828-5500 for your full model number and serial number ready). Model Number
Description
753-05762A OEM-390-679 490-241-0010 OEM-390-995 490-241-Y014 *Not compatible with Storm 2410.
Heated Grips* Drift Cutter Kit Polymer Skid Shoe Kit Snow Thrower Protective Cover Troy-Bilt Snow Thrower Maintenance...
Operation Manual - Page 28
...lawn care services or for a period of one (1) year, commencing on the date of the product sold through your property and/or to others and their respective possessions and territories, except those sold .
Phone: 1-866-840-6483, 1-330-558-7220 MTD Canada Limited - Normal Wear Parts are not genuine Troy-Bilt..., rider deck wheels, seats, snow thrower skid shoes, friction wheels,...
Similar Questions
What Is The Gap For Tb4bp Ec Troy Bilt Backpack Blower
What is the spark plug gap for troy bilt tb4bp ec Backpack blower
What is the spark plug gap for troy bilt tb4bp ec Backpack blower
(Posted by mcoulombeg 9 months ago)
We Are Finding It Impossible To Attach The Chute To The Snow Blower,storm 2410
The chute on our snow blower keeps coming off when clearing snow. It looks like the plastic pieces a...
The chute on our snow blower keeps coming off when clearing snow. It looks like the plastic pieces a...
(Posted by wfingerman 8 years ago)
Troy-bilt Storm 2620 Snow Thrower Is Blowing Oil
What can I do to stop my barely-used Troy-Bilt Snow Thrower from blowing oil out of the oil stick tu...
What can I do to stop my barely-used Troy-Bilt Snow Thrower from blowing oil out of the oil stick tu...
(Posted by cnchunter 8 years ago)
My Troy Bilt 2410 Start And Stops Rightaway And I Think Gas Is Leaking From Car
(Posted by yogi384 10 years ago)