Troy-Bilt Mustang 50 Support Question
Troy-Bilt Mustang 50 Support Question
Find answers below for this question about Troy-Bilt Mustang 50.Need a Troy-Bilt Mustang 50 manual? We have 2 online manuals for this item!
Question posted by py8834 on January 17th, 2023
Plug Gap
The person who posted this question about this Troy-Bilt product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by MercedesAMG on January 17th, 2023 12:38 PM
MercedesAMG
Member since:
January 26th, 2013 Points: 193,710
Member since:
January 26th, 2013 Points: 193,710
The spark plug gap for a Troy-Bilt Mustang 50 lawn tractor is typically around 0.030 inches (0.76 mm). It is important to note that this gap measurement can vary depending on the specific spark plug that is being used. You should always check the recommended gap measurement for the specific spark plug that you are using and adjust the gap accordingly.
To adjust the gap, you can use a feeler gauge to measure the distance between the center electrode and the ground electrode of the spark plug. If the gap is too large, you can use a spark plug gap tool to gently bend the ground electrode until the desired gap is achieved. If the gap is too small, you can use a small flat-head screwdriver to gently bend the ground electrode outwards to increase the gap.
It is important to make sure the gap is correctly adjusted to ensure proper engine performance and to avoid damage to the spark plug and other components of the engine. If you are not comfortable with adjusting the gap, you should consult a professional or refer to the owner's manual for additional instructions and guidance.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Troy-Bilt Mustang 50 Manual Pages
Operation Manual - Page 1
...-0019
Form No. 769-08505A (December 6, 2012) Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty
Operator's Manual
Mustang Series RZT
WARNING
READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE.
Operation Manual - Page 4
... making any public roadway.
15. This machine should evaluate their ability
to operate the riding mower safely enough to maintain traction, disengage the blades and proceed slowly and carefully straight down ...If the tires are involved in neutral, set parking
brake, stop before operating this
dump cart, lawn roller, etc.) on the slope gauge, do not mow it , do not operate this manual...
Operation Manual - Page 5
...gas appliances. Never over accidents, always look behind attachments (e.g. j.
m.
Disconnect the spark plug wire and ground against the engine to the presence of children. If the safety interlock ...Follow the manufacturers recommendation for weight limits for small children. loaded dump cart, lawn roller, etc.) on the machine and should read and understand the instructions and...
Operation Manual - Page 6
... model. After striking a foreign object, stop the engine, disconnect the spark plug wire(s) and ground against the engine. Thoroughly inspect the machine for your nearest...with factory setting of operation. Observe proper disposal laws and regulations for proper tightness. Mower blades are equipped with California and federal EPA emission regulations for damage (e.g., excessive wear...
Operation Manual - Page 11
...of the four available positions on the seat pan and into position before operating the mower. 1. Install the discharge chute deflector using the carriage bolts, push nuts and ...zip tie to the
chute bracket. 2. Never operate the mower deck without the chute deflector installed and in Figure 3-6 and securely tighten the hardware.
50" Deck Shown
Flange Lock Nuts
Figure 3-7
Discharge Chute
...
Operation Manual - Page 14
...the engine will also remind the operator of maintenance intervals for five minutes after every 50 hours of the throttle or throttle/choke control. This indicator also illuminates when the ... the engine is started during operation, check the battery and charging system for two hours (from 50-52, 100-102, 150-152, etc.).
If the indicator comes on during this indicator is illuminated...
Operation Manual - Page 20
...The tractor could overturn and cause serious injury.
1. Always slow down or stop before engaging the mower deck.
1. If the operator should leave the seat without disengaging the PTO and moving drive control... RH and LH drive control levers forward to move to stop and remove the key from your lawn ''browned'' by approximately 45° for any reason while on inclines with a slope in the...
Operation Manual - Page 22
...points with Cub Cadet 251H EP grease after every 10 hours of any
accumulation of the mower deck.
and V-belt. From the tractor operator's seat, start the engine and engage ...dry grass.
5. Do not use
P
Every 10 Hours
P P
Every 25 Hours
P P
Every 50 Hours
Every 100 Hours
Prior to the Engine Manual for all engine maintenance intervals, procedures, specifications and instructions...
Operation Manual - Page 27
...Washer Screw
Battery Hold-Down Bracket
Figure 7-1 2. Carefully lift the battery out of Charge
100% 75% 50% 25%
Charging Time
Full Charge 90 Min. 180 Min. 280 Min. Always use the same capacity ...). 4.
If the electrical system does not function, check for replacement. Deck Removal
Remove the mower deck from the negative battery post. 3. The muffler at a MAXIMUM rate of the following ...
Operation Manual - Page 36
... Sealant by Tire Aid™ Deluxe Tire/Tube Foot Pump by Tire Aid™ Tire Aid™ Deluxe Tire Plug Kit by Tire Aid™ 15" Tractor Tube with Sealant by Tire Aid™ 18" & 20" Tractor Tube...L014 490-328-L016
22216
Part
42" Mulch Kit 46" Mulch Kit 50" Mulch Kit 54" Mulch Kit 42" Bagger w/ Weight Kit 46" Bagger w/ Weight Kit 50" Bagger w/ Weight Kit 54" Bagger w/ Weight Kit Front Weight ...
Parts Manual - Page 2
TroyBilt Mustang 50" RZT
Frame
1
5
3 5
8 10
7 3
5
2
6
9 4
Ref. No.
1 603-04303D 2 703-05829 3 710-0520 4 710-3005 5 712-04065 6 732-0626 7 736-0300 8 738-04058 9 738-04162A 10 756-...
Parts Manual - Page 3
... x .10
13 737-3000 Fitting, Lube, 3/16 Drive
14 750-04775A Spacer, .51 x .75 x 5.825
15 750-04792 Hub, .76 x 1.23 x .92 Part No. TroyBilt Mustang 50" RZT
Front Axle
4
9
6 10
11
9
13
9 12
1
15 14
5
4 2
7 13
3
9
8 15
Ref. No.
Parts Manual - Page 4
TroyBilt Mustang 50" RZT
18 9
Electrical
4 14
10 4
3 9
18
2 6
15 12
11 6
1 16
13 8 7
5
9 17
Section of Main Wire Harness (Reference Only)
Parts Manual - Page 5
.../NC) - Tapp, #8-18 x .5 Screw, Hex Wash. Tapp, 1/4-20 x .375 Screw, Hex Cap, 1/4-20 x .75 GR5 Nut, Hex Sems, 1/4-20 Meter, Hour Switch, Dbl. Pole - TroyBilt Mustang 50" RZT
Electrical
Ref. Part No. Brake/Rev Solenoid Switch, Outer Seat Spring Switch, Inner Seat Spring Key Battery, 235 CCA Plate, Insulator Boss Plate, Insulator...
Parts Manual - Page 7
TroyBilt Mustang 50" RZT
Operator's Platform
Ref. Hd. Hd. Hd. Tapp. , 1/4-20 x 1.5 Screw, Hex Wash. Tapp., 1/4-20 x .5 Screw, Hex Wash. Hd Tapp, 5/16-18 x .75 Pin, Clevis, .5 x .78 ... Ht./Brake
Bracket, Foot Rest Graphic, Troy-Bilt Graphic, Ground Control
Bracket, Battery Hold Down Screw, Hex Wash. Part No. Hd. Hd Tapp, #12-16 x .50 Screw, Hex Wash.
Parts Manual - Page 9
... Screw, Shoulder, .5 x .434 Bearing, Hex Flange Bearing, Flange, .625 x .938 x .344 Rod, Lapbar Control Rod, Deck Front Hanger Rod, Deck Lift Handle Hub, Control TroyBilt Mustang 50" RZT
Operator's Controls
Ref.
Parts Manual - Page 11
.... Tapp, 5/16-12 x .75
12 710-1260A Screw, Hex Wash. No
Description
23 732-0306A Spring, Compression
24 732-0459 Spring, Extension, .94 Dia. TroyBilt Mustang 50" RZT
11
Mower Deck
Ref. Hd. No
Description
1 603-04328A Housing, Deck
777S32598
Graphic, Danger
777S30503
Graphic, Danger
777I22282
Graphic, Instruction
777D11833 Graphic...
Parts Manual - Page 12
TroyBilt Mustang 50" RZT
12
Engine Connections
23
20
7
9 17
32
24 13
22
10
27
31
4
16
30
11
28
8 1
26 12 25
2
18 6
5 12
3
18 29 6
33
6
14
21
15
19
Parts Manual - Page 13
TroyBilt Mustang 50" RZT
13
Engine Connections
Ref. Tapp 1/4-20 x .5
6 710-0654A Screw, Hex Wash. Tapp 5/16-12 x .75
8 710-3008
Screw, Hex Cap, 5/16-18 x .75 GR5
9 ...
Parts Manual - Page 14
... 738-04192 Rod, .405 x 14.0
14 747-04217C Rod, Bypass
15 750-04561 Tube, .45 x .69 x 10.2
16 754-04043 V-Belt, Type A Sec x 57.7
TroyBilt Mustang 50" RZT
14
Hydro Transmissions & Rear Wheels
8
7 12
10 4
1
8
8
16
2
14
13
4
5 15 6
31
9 11 56
10 7
12
Ref.
Similar Questions
Need New Motor Engine For Troy Bitl Riding Lawn Mower 15.5
(Posted by janicesutton60 2 years ago)
My Mustang Rzt 50 Was Running Fine I Got Off For A Minute ,got Back On And It Wo
I was using my mustang rzt 50 it was running fine. I got off of it for a minute got ck on and it won...
I was using my mustang rzt 50 it was running fine. I got off of it for a minute got ck on and it won...
(Posted by mob816 8 years ago)
What Oil Filter Should I Use On Mustang 50 Zero Turn Mower
(Posted by Clcneale 9 years ago)