Home » Troy-Bilt » Lawn & Garden » Troy-Bilt LS 27

Troy-Bilt LS 27 Support Question

Find answers below for this question about Troy-Bilt LS 27.
Need a Troy-Bilt LS 27 manual? We have 1 online manual for this item!

Troy-Bilt Overview Questions Manuals Reviews Videos Research

Question posted by airwolf62 on December 31st, 2015

Hyd Control Valve

control valve will not return to nutral when retrac cycle is compleat

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Troy-Bilt LS 27 Manual Pages

Operation Manual - Page 1

... Form No. 769-06118 (May 19, 2010) Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty Operator's Manual LS 27 TB - Log Splitter WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. Printed In USA TROY...

Operation Manual - Page 2

... complete satisfaction at the time of Contents Safe Operation Practices 3 Assembly & Set-Up 7 Controls & Features 11 Operation 12 Maintenance & Adjustment 15 Service 17 Troubleshooting 18 Replacement Parts 20... contacting our Customer Support Department. It instructs you how to do NOT return the machine to provide excellent performance when properly operated and maintained. Failure ...

Operation Manual - Page 3

...and disengage them b. This machine was built to be trained and supervised by cycling the valve control lever from forward to the following safety instructions could endanger the personal safety and...in this machine. Keep this symbol. Stop the engine and relieve hydraulic system 3. returning to or death. Read, understand, and follow all assemble and operate. Give attention ...

Operation Manual - Page 4

...personal injury can ignite. Never fuel machine indoors. i. Failure to operate the controls. 9. Do not operate machine while under good artificial light. Vertical Operating ... Handling of ignition. h. See Fig. 2-1. 13. Take appropriate firefighting equipment with all controls are explosive. Vertical Horizontal Figure 2-1 7. a. g. Never store the machine or fuel container...

Operation Manual - Page 5

... engine and should not be sure they are tight to do not stumble over it. 14. returning to the Consumer Products Safety Commission (CPSC) and the U.S. For your nearest engine authorized service dealer...hose clamps, and hydraulic fittings are in effective working order by cycling the valve control lever from forward to ensure that all federal, local, or state requirements are working condition. 5....

Operation Manual - Page 6

Read, understand, and follow all instructions in this power machine to persons who operates control handle. WARNING- BYSTANDERS Keep bystanders, helpers and children at a time. Your Responsibility-Restrict the use of this manual and on the machine. Symbol Description READ ...

Operation Manual - Page 8

...beam weld bracket by removing the two hex washer screws that secures it to the bottom of the control valve by removing the six hex screws. See Fig. 3-3. Be sure to keep hands away from the...weld bracket. Assembly & Set-Up Cut the strap near the hose on the side of the control valve, must be above the tongue assembly. Take extra care when raising and lowering the beam as ...

Operation Manual - Page 9

.... See Fig. 3-4. Reattach the log tray to the top of the beam with the control valve, aligning the holes in the tray with the previously removed hardware. Rotate the control handle into the weld brackets. See Fig. 3-8. The control handle is normal. 18. Remove the clevis pin and bow-tie cotter pin from the...

Operation Manual - Page 10

...8482; AW-32 Hydraulic Oil or 10WAW-ISO viscosity grade 32 hydraulic oil. Use the control handle to engage the wedge to burst with the following instructions in either the horizontal or ...vertical position. Extend and retract the wedge 12 complete cycles to may be easier when the splitter is "self- bleeding"). However, you MUST check...

Operation Manual - Page 11

... the wedge. See the Operation section for the location and function of the controls on the beam support latch bracket. Forward, Neutral and Reverse. This may occur...beam lock is designed to split the wood. Tongue Control Handle The control handle has three positions; Controls & Features 4 Cylinder Tongue Control Handle Log Dislodger Horizontal Beam Lock Beam Assembly Wedge ...

Operation Manual - Page 13

... the log dislodger, split to the NEUTRAL position to adjust or modify the control valve or the hydraulic system from wedge, move the lever 9. Do not attempt to stop wedge) Reverse (To return wedge) 3. Release the control handle or move the control handle to the REVERSE position until the wedge is not functioning properly, STOP...

Operation Manual - Page 14

...spider" type coupling between the engine and pump drive shafts. 7. Never: 1. Operate through relief valve for the engine to remove partially split wood from the jack stand. 3. Spring Clip Clevis ...Use an approved hydraulic fluid. See Fig. 5-5. 5. Attempt to adjust the unloading or relief valve settings. 5. Split wood along the grain (lengthwise) only. Use a breather cap on the...

Operation Manual - Page 15

... the spark plug wire and start the engine following the instructions in the reservoir every 100 hours of the tire for all times. Use the control handle to engage the wedge to the Engine Operator's Manual packed with force sufficient to drain into a suitable container.

Operation Manual - Page 16

...and retract the wedge 12 complete cycles to refill the tank will ..., stoves, electric motors, etc. 1. Hose Clamps Check the clamps on the return hose before each use of the threads are present such as follows: WARNING! ...pump or valve is "self-bleeding"). Off-Season Storage MAX MIN Hydraulic Fluid Only Figure 6-3 12. WARNING! NOTE: Always dispose of pressure washers or a garden hose to...

Operation Manual - Page 18

... service dealer. 2. Make certain pump inlet hoses are clear and unblocked. See authorized service dealer. 4. Shipping plugs left in coupling not adjusted properly. 4. Blocked control valve. 1. Incorrect oil level. 6. Internally damaged cylinder. 1. See authorized service dealer. 6. Flush and clean hydraulic system 1. See authorized service dealer. 5. See authorized service dealer...

Operation Manual - Page 19

... handle does not return to neutral when released from forward position 4. See authorized service dealer. Engine/pump misalignment. 3. Drain oil, clean reservoir and refill. 6. See authorized service dealer. 7. See authorized service dealer. 1. Replace hydraulic fluid. 3. Control valve leaking internally. 7. Damaged control valve. Remedy 1. Problem Cause...

Operation Manual - Page 20

... Coupling, .500 Set Screw 723-0405 Hydraulic Oil Filter 737-04308 727-04356 727-04288 727-0443 727-04362 Inlet Filter Inlet Hose Hydro Hose Return Hose Hydro Hose 726-0174 Hose Clamp 634-0186 Wheel Assembly, 16.0 x 4.8 x 8.0 Phone (800) 828-5500 to order replacement parts or a complete Parts Manual (have...

Operation Manual - Page 24

...or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for products sold . c. Service completed by someone other rights which...or limitations on how long an implied warranty lasts, so the above . Log splitter pumps, valves, and cylinders have other than the amount of the purchase price of the product as : ...