Troy-Bilt CSV 070 Support Question
Troy-Bilt CSV 070 Support Question
Find answers below for this question about Troy-Bilt CSV 070.Need a Troy-Bilt CSV 070 manual? We have 1 online manual for this item!
Question posted by lhruby on November 2nd, 2021
How To Replace Drive Belt
The person who posted this question about this Troy-Bilt product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Requests for more information
Request from lhruby on November 3rd, 2021 4:25 AM
A short video would be more helpful.
A short video would be more helpful.
Thank you
Current Answers
Answer #1: Posted by itasklive on November 2nd, 2021 9:00 PM
itasklive
Member since:
October 21st, 2021 Points: 257,510
Member since:
October 21st, 2021 Points: 257,510
Related Troy-Bilt CSV 070 Manual Pages
Service Manual - Page 1
... of outdoor power equipment of outdoor power equipment and continuing product changes that occur over time, updates will be necessary to assist the trained technician. CSV 070
NOTE: These materials are for use common sense when working on power equipment.
Service Manual - Page 3
TABLE OF CONTENTS
Safety Switch ...1 Inspection of the Drive System 3 Transmission Removal ...5 Impeller and Belt Removal ...8 Chipper Blade Removal ...11
0
Service Manual - Page 5
...will not start even though the bag is in place. The safety switch is mounted to the handlebar engages the drive system. There may be separated. The switch is a normally closed . When the collection bag or blower chute is...Shredder Vacuum
ABOUT THIS SECTION:
In model year 2000, MTD introduced a vertical crankshaft lawn vacuum with a removable vacuum hose. For the sake of the unit.
Service Manual - Page 6
... the switch and ground. Remove the switch from the magneto to run the engine without a blower chute or collector bag in place. This is pressed, replace the switch.
1.6. If the switch fails to work correctly. If slight pressure on the tab breaks continuity, adjusting the tab by bending it would be...
Service Manual - Page 7
...Belt Cover
Figure 1.11
NOTE: "OL" meter reading in the wiring or the ground connection.
1.13. If the switch works correctly, but does not ground the magneto, the problem lies in Figure 1.11 indicates no continuity. INSPECTION OF THE DRIVE...cable connects to service unless this safety feature works correctly. Does the drive system operate over the full range of speeds. Run the self ...
Service Manual - Page 8
... may be a problem in figure 2.4 2.5. To check the final drive gears, remove both rear hubcaps. Watch the travel . If the idler pulleys do not react properly, confirm that the belt is an internal transmission problem, replace the transmission.
2.9. Spring anchor bolt
Spring
Figure 2.4
NOTE: Belt removed for clarity in one of the variable speed...
Service Manual - Page 9
Remove vacuum hose if attached. 3.4. Using a 3/8" socket, remove the 3 self tapping
screws securing the belt cover. See Figure 2.12. This provides a ratcheting action. Pull the breaker bar rearward until the drive belt can be free to slide back and forth. Remove collection bag or blower chute. 3.3. See Figure 3.4.
Tensioner Arm
Square hole
Pin
Figure...
Service Manual - Page 10
... axle. It can be removed as the rear wheels are right hand and left hand drive gears 3.11.
See Figure 3.10. Right hand drive gear
Figure 3.10
NOTE: There are removed. See Figure 3.7.
3.10. Remove retaining ring holding drive gear and dowel pin on dust cover faces outboard 3.12. Remove dust cover NOTE...
Service Manual - Page 11
Remove barbed fitting holding the transmission to the brace.
Push the hexagonal drive axle bushings out of each side of the speed control collar. See Figure 3.18.
NOTE: Rotating the collar counter-clockwise will aid in removal. Actuating ...
Service Manual - Page 12
.../16" wrench and a 9/16" wrench remove height adjusters and cross bar.
Self-propelled Chipper Shredder Vacuum
3.19. Self propelled transmission Figure 3.19
3.20. IMPELLER AND BELT REMOVAL 4.1. At this manual. 4.3. Remove the hub caps. 4.5. Remove front wheels using an 1/2 wrench. 4.6. See Figure 4.6. Safely tilt and support the front of this point...
Service Manual - Page 14
...; The pulley hub can be replaced with a chock, to 425 inch pounds.
Pulley hub
Figure 4.16
4.17. Install a new belt though the hole surrounding the crankshaft. NOTE: When installing impeller make certain belt is seated in the pulley hub.
4.13. Block the impeller with out removing the impeller.
Drive belt
Chock Figure 4.11
4.12. NOTE...
Service Manual - Page 15
...
Impeller
Figure 5.3
Figure 5.5
NOTE: On installation, torque the chipper blade to 210 - 250 inch pounds.
11 Remove the black plastic nozzle as described in the BELT AND IMPELLER REMOVAL section of this manual. CHIPPER BLADE REMOVAL
5.1. See Figure 5.2.
The nuts on the flat head cap screws can be reached using a 1/2" socket...
Similar Questions
What Needs To Be Replaced
I love my machine..but right now it doesn't throw snow very well at all (it used to). Do I need to r...
I love my machine..but right now it doesn't throw snow very well at all (it used to). Do I need to r...
(Posted by mfitz7834 2 years ago)
Speed Shifter
Was wondering how to take this apart? The shifter for the speed seems only to be able to move slight...
Was wondering how to take this apart? The shifter for the speed seems only to be able to move slight...
(Posted by matty917 6 years ago)
Won't Restart When Warm.
won't restart when warm. Has to cool down for roughly 15-30".
won't restart when warm. Has to cool down for roughly 15-30".
(Posted by carlmatter 6 years ago)
Auger Belts
Why do the auger belts continue to pop off after a short period of time used?
Why do the auger belts continue to pop off after a short period of time used?
(Posted by chuckrita401 7 years ago)
Spark Plug Change
I'm trying to check the spark plug on my Troy-Bilt CSV 070. I cannot find a socket that will fit. Wh...
I'm trying to check the spark plug on my Troy-Bilt CSV 070. I cannot find a socket that will fit. Wh...
(Posted by davidcary 7 years ago)