Troy-Bilt CSV 070 Support Question
Troy-Bilt CSV 070 Support Question
Find answers below for this question about Troy-Bilt CSV 070.Need a Troy-Bilt CSV 070 manual? We have 1 online manual for this item!
Question posted by davidcary on November 6th, 2016
Spark Plug Change
I'm trying to check the spark plug on my Troy-Bilt CSV 070. I cannot find a socket that will fit. What size is the socket diameter and what spark plug should I buy to replace it?
Current Answers
Answer #1: Posted by Odin on November 6th, 2016 5:07 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
Find the parts for your product starting at http://www.partselect.com/MultiModels.aspx?ModelNum=CSV070&searchTerm=&RefineSearch=0. You can call the number at the upper right for any further questions. (Or use the contact information here--https://www.contacthelp.com/troy-bilt/customer-service.)
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Troy-Bilt CSV 070 Manual Pages
Service Manual - Page 1
... of publication. All Rights Reserved. However, due to the variety of outdoor power equipment and continuing product changes that occur over time, updates will be necessary to time. Service Manual
SELF PROPELLED CHIPPER VAC - CSV 070
NOTE: These materials are for use by trained technicians experienced in this publication, although care has been...
Service Manual - Page 5
... Chipper Shredder Vacuum
ABOUT THIS SECTION:
In model year 2000, MTD introduced a vertical crankshaft lawn vacuum with a removable vacuum hose. Do NOT force the lever.
• The control ... housing assembly. The switch is connected to one terminal of a self-propell feature. Check for this section was used for continuity through the switch, from the magneto primary wire...
Service Manual - Page 6
Remove the switch from the magneto to ground when the plunger is pressed, replace the switch.
1.6. Test the switch independently. It should complete a path from the frame using a 5/16" wrench or driver. NOTE: A lock tab secures the plug to work correctly. Figure 1.4
1.5. The switch should show continuity with the plunger up , it downward...
Service Manual - Page 8
...wheels when the self propel bail is an internal transmission problem, replace the transmission.
2.9. Remove the rear wheels using a 9/16... is routed properly. 2.6. See Figure 2.4.
See Figure 2.6. To check the final drive gears, remove both rear hubcaps. Watch the travel... the transmission input shaft, but fails to the changes in the transmission.
If the belt and pulley system...
Service Manual - Page 9
... side gear and an "L" on the correct side. This provides a ratcheting action. Using a 3/8" socket, remove the 3 self tapping
screws securing the belt cover. Self tapping screws
Right hand drive gear Figure... 3.4
3.5. Self-propelled Chipper Shredder Vacuum
2.11. lead from the spark plug. 3.2. Remove collection bag or blower chute. 3.3. Insert a 3/8" breaker bar and extension into the square hole...
Service Manual - Page 11
Remove spring from transmission using an 3/8 socket.
3.14.
See Figure 3.15.
Figure 3.17
3.18. Self tapping screws
3.17. Disconnect Z-fitting from transmission actuating arm. (This is the variable speed cable).
Figure 3.18
7 Bushing
Variable speed cable
Barbed fitting
Figure 3.15
3.16. NOTE: Z-fitting must be installed from the bottom of frame. Remove the two phillips...
Service Manual - Page 12
... rear cross bar
8 Once the left side comes out, slide the transmission to the right. Install new transmission in your hands
3.21. lead from the spark plug. 4.2.
Remove the hub caps. 4.5. IMPELLER AND BELT REMOVAL 4.1. Remove front wheels using an 1/2 wrench. 4.6. See Figure 4.6. Remove the transmission as described in the
TRASMISSION REMOVAL...
Service Manual - Page 14
...inch pounds. Pulley hub
Figure 4.16
4.17.
Chipper blade
Figure 4.13 4.14. Using a 9/16" socket, remove the bolt,
lock washer, and flat washer securing the impel-
Drive belt
Chock Figure 4.11
... though the hole surrounding the crankshaft. Do not use an impeller that shows any damage, replace as needed. Refer to create slack, releasing the belt from
rotating. Block the impeller with...
Service Manual - Page 15
... BELT AND IMPELLER REMOVAL section of this manual.
5. Chipper chute
Figure 5.2
5.3. See Figure 5.5. lead from the spark plug.
5.2.
Self-propelled Chipper Shredder Vacuum
5.4. The nuts on the flat head cap screws can be reached using a 1/2" socket, universal, and extension. CHIPPER BLADE REMOVAL
5.1. Using 3/16" allen wrench, remove the flat head cap screw that...
Similar Questions
How Do You Get The Boot Off The Spark Plug
how do you get the boot off the spark plug
how do you get the boot off the spark plug
(Posted by Anonymous-170839 2 years ago)
Spark Plug Gap Set
what should the spark plug for. my tb625 ec troy built weed eater be gapped at?
what should the spark plug for. my tb625 ec troy built weed eater be gapped at?
(Posted by ginac566 6 years ago)
Speed Shifter
Was wondering how to take this apart? The shifter for the speed seems only to be able to move slight...
Was wondering how to take this apart? The shifter for the speed seems only to be able to move slight...
(Posted by matty917 6 years ago)
Won't Restart When Warm.
won't restart when warm. Has to cool down for roughly 15-30".
won't restart when warm. Has to cool down for roughly 15-30".
(Posted by carlmatter 6 years ago)
