Singer 8768 HERITAGE Support Question
Singer 8768 HERITAGE Support Question
Find answers below for this question about Singer 8768 HERITAGE.Need a Singer 8768 HERITAGE manual? We have 1 online manual for this item!
Question posted by Karenglassbrenner on February 15th, 2016
C2 Problem
I have a singer heritage sewing machine with 8768 number, I was sewing with no problems and suddenly the c2 button appeared. What am I doing wrong
Current Answers
Answer #1: Posted by waelsaidani1 on February 15th, 2016 11:37 AM
waelsaidani1
Member since:
May 12th, 2013 Points: 19,501,797
Member since:
May 12th, 2013 Points: 19,501,797
Does the machine have a buttonhole lever on the right hand side of the
needle that has to be pulled down before starting the buttonhole?
needle that has to be pulled down before starting the buttonhole?
Insert the button into the special button hole foot. put the foot on the machine.Pull down the button hole lever( It's near the presser foot lever towards the back of the machine). Place your needle where you want the button hole to be. Select the button hole pattern and press on the pedal. Watch for the end of the button hole.
Related Singer 8768 HERITAGE Manual Pages
Instruction Manual - Page 2
... Limited S.à r.l. Do not modify the plug in order to electrical/electronic products. or its Affiliates. ©2013 The Singer Company Limited S.à r.l. "Read all moving parts. "WARNING- "Use this sewing machine only for its service agent or similarly qualified persons in any opening." 8. "Indoors use bent needles." 16. "Keep fingers away from...
Instruction Manual - Page 5
... tension 24 - 25 Changing presser foot 24 - 25 Control panel functions 26 - 27 Reverse operation button 28 - 29
2. CARING FOR YOUR MACHINE Cleaning hook area and feed dogs 50 - 51
Cleaning the sewing machine and foot controller
4. STARTING TO SEW Quick reference table of stitch length and width ---------- 30 - 31 Straight stitching 32 - 35
Keeping...
Instruction Manual - Page 8
... control
3
4. Face cover
4
6. Reverse stitch button
11. Power/light switch
15. Alternate thread cutter
14
27. Needle plate
32. Instruction manual
20
21 22 23 24
1
8
9
10
11
19
16 17 18 25 26 27 28 29 30 31 32
33
34
35
6 1. KNOWING YOUR SEWING MACHINE
MACHINE IDENTIFICATION
1. Bobbin winder shaft
5
9. Bobbin winder...
Instruction Manual - Page 10
...Buttonhole foot
The foot that comes on your sewing machine is another very useful foot and should be used for the majority of your sewing. Spool pin cap (medium) 7. Satin ... Bobbins 3. Spool pin cap (large) 8. especially honeycomb , star a etc. Screwdriver for most of your decorative sewing - The satin foot (11) is called the general purpose foot and will be sure they are Class I5 ...
Instruction Manual - Page 12
... "OFF" Mettez l'interrupteur moteur/ lumière à la position « Fermé » Poner el Interruptor de corriente/luz en "OFF"
Machine socket Prise du cordon de la machine Conector de la máquina
2
1
Pin plug Butée Conector
3
Power line cord Cordon d'alimentation
Cordón de la linea elé...
Instruction Manual - Page 14
... contrôle des griffes Control de dientes
CONVERTING TO FREE-ARM SEWING
Your machine can be placed to the right. To replace, slide the extension table back into a slim ... be used .
With the extension table in position, it off to the left while pushing the release button (A) with left hand and pull it provides a large working surface as shown. SPOOL PINS HORIZONTAL SPOOL PIN...
Instruction Manual - Page 16
... end of bobbin. Place bobbin onto shaft with the spool pin cap. After the bobbin has begun to fill, stop turning
when completely filled. Start machine. Step on the spool pin, and secure it clicks. Push bobbin winder shaft to remove
bobbin and cut
4
the thread tail. Hold onto end of...
Instruction Manual - Page 18
... the
5
thread until it stops in the slot (B). Pull thread through the slot (A) and then to its highest position by pushing the release button to remove the cover.
3. NOTE: Sewing can be started without picking up sufficiently to
2
allow you pull the thread.
3
NOTE: This is pulled.
4. THREADING THE BOBBIN THREAD
1. Raise...
Instruction Manual - Page 20
...foot lifter is threaded properly in its highest position. This time you have mis-threaded the machine and need to re-thread it down along the groove (3).
* Guide the thread into the... then pull it . C.
You should detect a considerable amount of resistance and much more deflection of the machine. A B
C
18 Turn the hand wheel counter clockwise until the needle is in the tension discs,...
Instruction Manual - Page 26
...the balanced tension of both top and bobbin threads.
Push presser foot release button to a higher number or a lower number may improve sewing appearance. Place the desired foot on the bottom side of your fabric. The ... irregular, you find that the foot holder snaps
on top of the machine. If, when you start to sew, you will need to adjust the tension control.
Lower the presser foot...
Instruction Manual - Page 28
...sew straight stitch.
Stitch length and width/needle position controls
Your sewing machine will change the length, width or straight stitch needle postition according to red at the auto / default position. Number...aiguille. To select other patterns, push the pattern selection button. At this point you power off the machine. Note: Instructions for manual adjustments than others.
26
...
Instruction Manual - Page 30
... de marche arrière Interruptor de puntadas hacia atrás
* Reverse stitch function for tie-off of other stitches ( ) The sewing machine makes 4 tiny tacking stitches to tie off the sewing pattern to sew in the pattern where the reverse/tacking stitch button is pushed.
The machine will be at the start and end of...
Instruction Manual - Page 34
... fabric, stop the sewing machine. The guide line on the needle plate. When reaching the edge of face cover as those in doll clothes or baby garments.
32
3/4" (19 mm) 5/8" (16 mm) 1/2" (13 mm) 3/8" ( 9 mm) 1/4" ( 6 mm) NOTE: To secure the stitching and avoid raveling, press the reverse stitch button and sew a few stitches at...
Instruction Manual - Page 36
When
sewing, the machine will pull this thread to sew. Thread machine with different tension and stitch length combinations.
34 Start to the top. 2.
Increase thread tension a little at a time and continue until
you acheive the desired appearance. 4.
HAND-LOOK QUILT STITCH
This stitch is designed to the main fabric piece for sewing. INSERTING ZIPPERS AND PIPING...
Instruction Manual - Page 38
... stitch width is pulling to the scale and number markings on the top of stabilizer for satin stitching. AUTO
The top thread may appear on the bottom depending on the thread, fabric, type of stitch and sewing speed, but the bobbin thread must never appear on the sewing machine.
NOTE: The values shown in the chart...
Instruction Manual - Page 48
...on your garment. 6. Lower the buttonhole lever (C) so that measures the size of the button and calculates the size buttonhole required. Stabilizer or regular interfacing can be used.
* Make... presser foot" on a scrap of the actual fabric from your button.
1.
SEWING A BUTTONHOLE
USING BUTTONHOLE FOOT
Your machine offers you two different widths of bartack buttonholes sewn by a system...
Instruction Manual - Page 52
..., keep the essential parts clean at its highest position.
2
2. Remove the bobbin case (2).
3
4. CARING FOR YOUR MACHINE
CLEANING HOOK AREA AND FEED
DOGS
Always disconnect the machine from power
1
supply by the arrows. (A, B)
NOTE: Singer brand sewing machine oil is necessary to remove dust from the electrical
CAUTION outlet.
To ensure the best possible operation...
Instruction Manual - Page 54
... most useful for appliqueing and bar tacking. Thread the two threads as an alternative to your Singer retailer. Turning off the machine returns the machine to selecting a pattern. STRAIGHT STITCH NEEDLE POSITION
The position of the needle when sewing straight stitch may be set beyond a twin needle mark, regardless of sizes. NOTE: Needle threader...
Instruction Manual - Page 56
... thread tension is too tight (see page 23). * Needle is bent or blunt. - Remove lint (see page 23). PERFORMANCE CHECKLIST
GENERAL PROBLEMS
Machine does not sew. * Power switch is not raised when sewing stitch patterns.
- Replace needle (see page 50 -51).
Guide it gently. * Needle size is not correct for thread and fabric (see...
Instruction Manual - Page 58
...from bobbin winder shaft. The reverse button is engaged (lower position). Raise buttonhole lever and begin sewing. 3. Buttonhole stitch is selected on control panel
Problem Correction
1. It only...lamps above the stitch selection panel on the machine. When a message is in the machine socket for the function you may fix the problem by an arrow.
Helpful message...
Similar Questions
The Heritage 8768 Handwheel Is Completely Different How Do You Put Back On?
It's not like other singers
It's not like other singers
(Posted by kathyshepstone 10 months ago)
The Start/stop Light And 2nd Light On The 2nd Row Are Blinking.
I have just installed the machines software and turned the machine on. Why are these lights blinking...
I have just installed the machines software and turned the machine on. Why are these lights blinking...
(Posted by melissacorn 9 years ago)
Pin Popped Out On The Auto Threader ! Singer 8768
A pin popped out on my three month old singer heritage sewing machine. the pin is from theauto threa...
A pin popped out on my three month old singer heritage sewing machine. the pin is from theauto threa...
(Posted by skeyc78 10 years ago)
What Is The Meaning For Error Code E2 On Singer Stylist Model 7258
Trying wind a bobbin and after about 3 turns it stops and give an E2 error code. Why?
Trying wind a bobbin and after about 3 turns it stops and give an E2 error code. Why?
(Posted by Anonymous-123220 10 years ago)