Singer 2250 Tradition Support Question
Singer 2250 Tradition Support Question
Find answers below for this question about Singer 2250 Tradition.Need a Singer 2250 Tradition manual? We have 1 online manual for this item!
Question posted by ianrcox56 on April 22nd, 2016
Thread Questions
The thread is gathering at the bobbin on my singer tradition 2273 what am i doing wrong please.I have rethreaded it many times but to no avail
Current Answers
Related Singer 2250 Tradition Manual Pages
Instruction Manual - Page 2
...sewing machine from the electrical outlet when removing covers, lubricating, or when making any air openings blocked. Do not unplug by the manufacturer or its intended use as threading needle, changing needle, threading bobbin... the following: Read all instructions before using and before cleaning. 3. The wrong plate can cause the needle to persons: 1. To disconnect, turn off ...
Instruction Manual - Page 6
... extension table 8 Connecting machine to power source 10 Changing the bulb 12 Two-step presser foot lifter 14 Darning plate 14 Attaching the presser foot shank 16 Winding the bobbin 18 Inserting the bobbin 20 Inserting and changing needles 22 Threading the upper thread 24 Thread tension 26 Raising the bobbin thread 28 Reverse sewing/ Removing the work/ Cutting...
Instruction Manual - Page 9
Presser foot
5. Bobbin stopper
4
9. Needle plate
6. Removable extension table/ accessory storage
3
7. Reverse sewing lever
10
8. Stitch length dial
10. Thread cutter
2
9
4. Thread take-up lever
1
8
3. Pattern selector dial 5
6
2 Thread tension dial
7
2. GB Principal parts of the machine
1.
Instruction Manual - Page 11
Main plug socket
17. Upper thread guide
19. Presser foot lever
15
22. GB Principal parts of the machine
11. Handwheel
13
19
15. Horizontal spool pin
11
17
12. Foot speed control
23. Power cord 16
22
23
4 Power and light switch
14
20
16. Bobbin winder
12
13. Hole for second spool pin
18
14. Face plate
20. Handle
21. Bobbin thread guide 21
18.
Instruction Manual - Page 13
Zipper foot c. they are not supplied with this machine; Quilting foot n. Satin stitch foot r. Spool pin felt
6 Button sewing foot e. L-screwdriver f. Bobbin (3x) j. Overcasting foot o. Darning foot s. Darning plate l. Spool holder
Optional accessories (2) (These 8 accessories are however available as special accessories from your local dealer.) m. Hemmer foot p. Oil ...
Instruction Manual - Page 17
... does not fit, contact a qualified electrician to be used with the appropriate polarized outlet. (2)
Attention: Unplug power cord when machine is not in use .
Foot control The foot control pedal regulates the sewing speed. (3)
Attention: Consult a qualified electrician if in doubt of electric shock, this plug is intended to a power source as...
Instruction Manual - Page 25
...winder tension discs. (4)
- Step on to left (sewing position).
18 Snap thread into thread guide. (3)
- Cut thread. (9)
- Push bobbin spindle to spool pin. (1/2)
- Push bobbin spindle to the left (10) and remove.
4
5
6
7
8
9
10
Please Note:
When the bobbin winder spindle is in "bobbin winding" position, the machine will not sew and the hand wheel will not turn. To start...
Instruction Manual - Page 31
... the spool as shown. For small thread spools, place small side of thread on the holder with built in thread cutter. (8)
24 Thread tension module by not doing so several sewing problems could result.
1
- Draw thread from spool through the upper thread guide (3) and pulling thread through the slotted eye of thread to the rear beyond the needle eye...
Instruction Manual - Page 33
... only desirable for zig zag and decorative sewing. Thread tension too loose for straight stitch sewing. Proper setting of fabric.
1
2
Lower thread tension To test the bobbin thread tension, remove the bobbin case and bobbin and hold it by suspending it will be less than for straight stitch sewing. Normal thread tension for straight stitch sewing. For zig zag and decorative...
Instruction Manual - Page 37
... a seam, press down to its highest position, raise the presser foot and remove work behind the needle and presser foot. (2)
Cutting the thread
Pull the threads under and behind the presser foot. Release the lever and the machine will sew forwards again. (1)
Removing the work
Turn the handwheel toward you (counterclockwise) to bring the...
Instruction Manual - Page 39
... and vinyls.
(Use heavy foot pressure-large numbers.)
IMPORTANT: Match needle size to medium). NEEDLE, FABRIC SELECTION
NEEDLES
EXPLANATION
SINGER 2020 Standard sharp needles.
For best sewing results always use the same thread on natural woven fabrics for best
Heavyweight fabrics-canvas, woolens, outdoor tent and results.
TYPE OF FABRIC
Natural woven fabrics...
Instruction Manual - Page 49
Note: It takes practice to catch one or two fabric threads. (2)
Unfold the fabric when hemming is completed and press. Place fabric
...of the fabric with edge of the folded fabric.
1 Start to sew slowly on the fold, making sure the needle touches slightly the folded top to sew blind hems. Always make a sewing test first.
GB Blind hem/ Lingerie stitch
For hems, curtains, trousers...
Instruction Manual - Page 53
... the foot, so that marking on the buttonhole foot aligns with the stitch pattern selector dial.
Slightly reducing upper thread tension will produce better
results. - The zig-zag should sew over the heavy thread or cord. (A)
46
Use seam ripper and cut buttonhole open from one step to another with starting marking on...
Instruction Manual - Page 55
... The zipper foot can be attached right or left, depending on " ".
It is also possible to sew a length of the foot you are going to zipper foot. "4" (according to form a "welt" or piping.... (2)
1
2
48 Lower the foot and continue to sew.
GB Zippers and piping
Set the machine as illustrated. Dial selector on which side of cord into the fabric, raise the presser...
Instruction Manual - Page 59
... finger and tighten the screw (c). (4) For darning, first sew around the edge of the hole (to secure the threads). (5) First row: Always work by the operator. Note: Free motion darning is recommended for easier sewing and better results. A darning hoop is accomplished without the sewing machine internal feed system. Press the darning foot on firmly...
Instruction Manual - Page 65
The quilting guide supplied with your machine will help you sew straight, perfectly parallel lines.
58 GB Quilting functions
* The Quilting foot is used to produce perfect 1/4" seams.
Use it to seam squares or patches and for channel quilting. This foot is an optional accessory not included with your machine.
Instruction Manual - Page 71
... and press wrong sides together on pulled thread line or marked lines. Repeat, sewing in your fabric, either pull a thread to mark the fold or mark with chalk or marking pencil. Stitch 1/8 of an inch from fold line. Stitch Length: 2 - 3 Sewing Instructions: To mark pintucks in the same direction for each tuck. GB Traditional pintucks
Machine Preparation: -
Instruction Manual - Page 73
... sew the length required.
When seam is complete, raise the needle to it's highest, raise the presser foot and pull the upper and lower threads to reset your first row of the seam, begin by pulling on the bobbin thread. Loosen upper tension slightly. Note: Don't forget to the back of thread. GB Gathering
Machine Preparation: -
Secure thread...
Instruction Manual - Page 77
... intervals at the point (6) (1-2
6
drops) with sewing machine oil. Snap the two hook retaining arms
(3) outwards. Replace the hook (5).
7
5
Replace the hook race cover and snap back the two hook
retaining arms. Insert the bobbin case and bobbin and
replace the needle plate.
4
Important:
3
Fabric lint and threads must always be removed regularly. Turn the...
Instruction Manual - Page 79
... adjusted. 3. The stitch length is wrong. 4. The bobbin case is not threaded correctly. 2. Loosen the thread tension.
1. Only use good quality sewing machine oil.
4. Remove the upper thread and bobbin case, turn the handwheel backwards and forwards by
the machine.
1. The machine is not inserted correctly. 2. Check both bobbin and bobbin case. 3. The needle is too...
Similar Questions
I Get E7 Error Message On My Singer Model 7258 Sewing Machine. There Is No Refe
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
Error message E7 is up on my Singer Stylist model 7258 sewing machine. It is not working at all. I t...
(Posted by ebellamybellamy9 5 years ago)
Beeping From Singer Sewing Machine Stylist Ii 5625
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
My sewing machine will beep and stop sewing after three inches of sewing. I have taken it to be repa...
(Posted by arusheria 9 years ago)
Sewing Elastics Into Lycra
When sewing the elastic int the leotard the zig zag stitch is gather at the back making the stitch l...
When sewing the elastic int the leotard the zig zag stitch is gather at the back making the stitch l...
(Posted by sampennisi 10 years ago)
Something Is Wrong With The Straight Stitch.
My straight stitch seems to have problems even though I did everything I know to fix it. The upper t...
My straight stitch seems to have problems even though I did everything I know to fix it. The upper t...
(Posted by nafangr 10 years ago)
Please Help
What stitch and tension should i use if I'm trying to sew oilcloth with a singer tradition 2250 sewi...
What stitch and tension should i use if I'm trying to sew oilcloth with a singer tradition 2250 sewi...
(Posted by Anonymous-93802 11 years ago)