Sharp XEA21S Support Question
Sharp XEA21S Support Question
Find answers below for this question about Sharp XEA21S - Thermal Fax Machine.Need a Sharp XEA21S manual? We have 1 online manual for this item!
Question posted by labbepd on January 28th, 2020
Driver For Sharp Xea21s
I lost my CD installation. How can I find the driver for installing my cash register Sharp XEA21S?
Current Answers
Answer #1: Posted by hzplj9 on February 10th, 2020 12:54 PM
hzplj9
Member since:
June 25th, 2012 Points: 4,875,710
Member since:
June 25th, 2012 Points: 4,875,710
Haven't found any info on a CD. However it may only be the programming manual in CD format. This is a link to the manual which gives the details on how to program it.
https://www.manualslib.com/products/Sharp-Xea21s-Thermal-Fax-Machine-113325.html
Good Luck.
Related Sharp XEA21S Manual Pages
Instruction Manual - Page 3
... On the printer, a cutter to page 7. Installation in such locations could cause the register to discoloration or deterioration of the SHARP Electronic Cash Register, Model XE-A21S. The use a dry, soft... to cut the paper roll is after initializing the cash register. The water could seep into the cash register before operating your machine in a location that is a trademark of different ...
Instruction Manual - Page 6
...Refer to page 66.)
USB port
Use only the USB cable (manufactured by SHARP) supplied with the XE-A21S for the connection with the print roller arm ...result in damage to remove. Caution: The paper cutter is a one station type thermal printer, therefore it does not require any type of the printer cover to the...To re-install, hook the pawls on the printer cover. Be careful not to cut yourself....
Instruction Manual - Page 8
... must replace with
new ones immediately. " " is smaller than the sales amount. Machine state symbols
: Appears during programming.
: Appears when an error is detected.
: ... details.
: Appears when the batteries are not installed, or the installed batteries are dead. You must replace with
new ones within two days. When you have registered ten times, the display will show "0."(2 →...
Instruction Manual - Page 12
... are listed below.
• PLU (price lookup) • Consecutive number • Machine number • Receipt or journal printing selection (factory setting: receipt printing) • Power...apply taxable status other necessary items
While the cash register is pre-programmed so it can be trained
Department programming:
The cash register is pre-programmed for departments as follows:
...
Instruction Manual - Page 23
...item (dept. 12) for taxable, it finalizes an item entry.
6 Tax Calculation
Automatic tax
When the register is programmed with a tax rate (or tax table) and the tax status of each transaction by pressing... is set for cash with 50 cents as a non-taxable one $7.15 item (PLU no. 85, taxable 2) for cash
Key operation example
Print
5 @ 670 ! 85 p A
Manual tax
The machine allows you to ...
Instruction Manual - Page 24
...4 item allowed
In case of each
key is applied: When using a tax status shift, the entry of a multi-taxable item for cash with their programmed tax status reversed
• One $13.45 item of dept. 16 (non-taxable) as a taxable 1 item
•...or
keys before those keys. A
When Canadian tax system is resumed. Tax status shift
The machine allows you to shift the programmed tax status of ;
Instruction Manual - Page 28
..., enter the amount and press the
key.
Key operation example
Print
a
(a = 500 * A)
26
Cash tendering only available for RA and PO operation. The drawer will
print "NO SALE" on -account (RA...add code number is a good idea to use
the r key or the R key respectively. If you let the machine print a non-add code number before pressing
A the
key, a no sale, just press the
key. r For...
Instruction Manual - Page 31
...roll, replace
it to MAINTENANCE section for the replacement).
2. Program necessary items into the cash register.
Every time you must be entered using the month-day-year (MM/DD/YYYY) format... first program necessary items so that the cash register suits your sales manner.
To change the format, refer to print samples in the machine. Procedure for your reference. If there is...
Instruction Manual - Page 42
...
Footer printing
• This option decides whether or not the machine should print a message at the bottom of allowable digits for ... • For the and keys, program upper limit entry amount for total cash amount which can be handled on page
45. Key operation example
018 @ CA... 0 to "Logo messages" section on the register. Entry digit limit is prohibited. The entry digit limit
is...
Instruction Manual - Page 43
...SHARP" in for entering double size characters. The following are two ways for programming text: using character keys on the keyboard or entering character codes with zero). N N N 1 Press the
key to character codes
entry mode. If you press the key without pressing the
key, the cash register... program the word "Clerk01" with the
key, the cash register will be entered (even if it .) Set the...
Instruction Manual - Page 55
...entering power save mode in 30 minutes) • Logo message print format (graphic logo only) • Thermal printer density (standard density) • Online time out setting • Language selection (English) • Training... your sales needs. 4 Various Function Selection Programming 2
The cash register provides various options so you can use on this section, you specify a clerk code who...
Instruction Manual - Page 58
a If you program frequently performed transactions or report sequences for weekly or monthly reports).
5 Reading Stored Programs
The machine allows you can recall those a transactions and/or reports simply by pressing the key in the PGM mode. entering a PLU 2 item (programmed unit price: 1.50) ...
Instruction Manual - Page 60
When a clerk in training is valid only in page 55. The training operation is selected, the machine automatically enters training mode. The corresponding clerk memory is used when the operator or the manager practices register operations. Key operation example
A clerk set in training mode. To specify a clerk to be trained, refer to H from...
Instruction Manual - Page 66
... memory card.
You can load the graphic logo data created with "Easy Programming Tool" into the cash register through an SD memory card between your cash register and a PC when managing the data in your cash register by using the SHARP's PC software "Customer Support Tool." HOW TO USE AN SD MEMORY CARD
1 What You Can Do...
Instruction Manual - Page 67
Sharp is transferred from your cash register to the inserted SD memory card and vice
l versa, it will be sure to format it in advance. ...PC or replace the card with a new one . The SD memory card is accessed. When using a new SD memory card, be lost data.
• 128-Mbyte to 512-Mbyte SD memory cards are available and the relationship between the memory card capacity and the maximum ...
Instruction Manual - Page 72
...
When power is lost, the machine retains its memory contents and all information on sales entries.
• When a power failure is encountered in register idle state or during an entry, the machine returns to normal...contact with glue, thinner or a freshly copied blueprint, and heat caused by SHARP. • Do not unpack the thermal paper until it . • Avoid heat. The printer
will print the...
Instruction Manual - Page 73
... mm) Quality: Thermal paper
• Be sure to set the paper roll prior to using your machine, otherwise it may cause a malfunction. Paper specification Paper width: 2.25 ± 0.02 in the proper direction. Otherwise, if the AC power cord is plugged in memory will be cleared. Make sure that the cash register is disconnected...
Instruction Manual - Page 76
... paper roll correctly by following the steps in
"Installing the paper roll".
8 Removing the Drawer
Coin case
The drawer in the register is mounted on the printer cover. Be
careful not... the print roller arm, and open if it by following the steps in the direction of the machine in "Installing the paper roll".
7 Cleaning the Printer (Print Head / Sensor / Roller)
When the printed ...
Instruction Manual - Page 77
...?
• Is a clerk code assigned to the register? • Is the mode switch set properly at the "REG" position?
• Is the paper roll properly installed? • Is there a paper jam? •... to refer to any other position than "OFF".
(3) The display is illuminated, but the whole machine refuses registrations.
(4) No receipt is issued.
(5) No journal paper is taken up spool.)
•...
Instruction Manual - Page 118
... BELOW. Correction of defects, in the United States.
Your Product:
XE series Electronic Cash Register
Warranty Period of which has been damaged or defaced, which has been subjected to you...repairs or attempted repairs performed by anyone other than those described herein or to a Sharp Authorized Servicer. Additional items excluded from Any consumable items such as paper supplied with ...
Similar Questions
I Have An E02 Error On My Sharp Xe-a21s
I have an E02 erro. How can I fix it
I have an E02 erro. How can I fix it
(Posted by acabale 2 years ago)
Cash Register Xea21s How To Change The Tax
(Posted by raibw 10 years ago)
My Cash Register Xea21s, Has An L On The Display And Is Not Working
My cash register Sharp XEA21S is not working, when we trun it on an L sign comes up
My cash register Sharp XEA21S is not working, when we trun it on an L sign comes up
(Posted by dwgardens 10 years ago)
Our Sharp Ux-106 Fax Machine Allows Us To Send But Not To Receive. Help!
(Posted by emf3 11 years ago)
Delete The Activity Report On An Old Sharp Fax Machine Fo 3350?
How do you delete the activity report on an old Sharp Fax machine FO 3350?
How do you delete the activity report on an old Sharp Fax machine FO 3350?
(Posted by luterman45 12 years ago)