Schwinn 860 Treadmill Support Question
Schwinn 860 Treadmill Support Question
Find answers below for this question about Schwinn 860 Treadmill.Need a Schwinn 860 Treadmill manual? We have 2 online manuals for this item!
Question posted by mcthomson2 on April 30th, 2021
I Have A Schwinn 860 Treadmill With Incline Stuck In Up Position E7 Code. How Do
how do I enter calibration mode? What other solution is abailable
Current Answers
Answer #1: Posted by techyagent on April 30th, 2021 12:43 PM
techyagent
Member since:
June 17th, 2014 Points: 4,799,790
Member since:
June 17th, 2014 Points: 4,799,790
- Turn the power OFF, wait 5-seconds and turn back ON.
- Get into test mode and enter through the I/O testing step. ...
- Once the unit is in the mid-level position, power the treadmill off for 5-seconds and then power it back ON.
- Start the treadmill.
Thanks
Techygirl
Related Schwinn 860 Treadmill Manual Pages
Assembly and Owner's Manual - Page 2
...; 2010 Nautilus, Inc., All rights reserved ™ and ® indicate a trademark or registered trademark. Nautilus, Inc. (www.nautilus.com) trademarks include NAUTILUS®, BOWFLEX®, SCHWINN® and UNIVERSAL® and respective logos. Patent Information
This product may be covered by US and Foreign Patents and Patents Pending.
2 Assembly
3 Important Safety...
Assembly and Owner's Manual - Page 4
... to CAN/CSA-C22.2 No. 68-92. Certified to ANSI / UL1647. 4th ED. RoHS
Power Requirements
120VAC 15A 60Hz Non-GFI grounded outlet (dedicated circuit)
Schwinn® 860 Treadmill
Dimensions
Length
78" / 198 cm
Width
34" / 86 cm
Height
54" / 137 cm
Assembled Unit Weight Folded
Shipping Weight
211.6 lb / 96 kg
41...
Assembly and Owner's Manual - Page 5
...5. Allow a workout area of minimum 201" x 71" (5.1m x 1.8m). Do not connect the treadmill to loosen, unless instructed otherwise. 4. When attaching 2 pieces, lightly lift and look for each assembly step.... 3. For safe operation, the location must be on them. Note: The treadmill is designed to help insert the bolt through the bolt holes to plug into a grounded, ...
Assembly and Owner's Manual - Page 6
... Nuts, pre-installed
2
M8 x 70L Flathead Hex Screws
4
M4 x 10L Phillips Head Screws, pre-installed (model 840)
6
M4 x 10L Phillips Head Screws, pre-installed (model 860)
2
#8 x 1/2L Phillips Head Bolts, pre-installed
4
M8 x 15L Button Head Hex Screws, 2 pre-installed
4
M8 washers, 2 pre-installed
6
Assembly and Owner's Manual - Page 8
Keep your hands clear of the area between the Ergo Bar and the Upright. Assembly
1. Note: Schwinn® 840 model is shown. The Schwinn® 860 model has the console pre-assembled.
8
Unfold Frame Note: Hold one Upright (1A) and the Ergo Bar (1B) when you lift the folded uprights into position.
Assembly and Owner's Manual - Page 15
8. Attach Side Covers and Rear End Cap (model 860 only) Note: Hardware is pre-installed on rear support bar and not on Hardware Card.
15
Assembly and Owner's Manual - Page 16
... Cord
Final Inspection
Inspect your machine to lengthen. • Adjust the foot on the other side if necessary.
16
Leveling the Machine
To stabilize the treadmill, adjust the 2 feet below the front of the base frame.
• Lift one side of the machine and turn the foot -
Assembly and Owner's Manual - Page 19
... machine is equipped with and/or being injured on the machine - If it does not fit the outlet, have a correct outlet installed by a licensed electrician. Be sure to decrease ... protector or extension cord for safe storage when not in an emergency.
Emergency Stop Procedures
The treadmill is equipped with a Safety Key that no other equipment is correctly grounded.
When you are...
Assembly and Owner's Manual - Page 23
...) keys to:
• Adjust the Incline in your workout data. Consult a physician before you adjust the machine settings, make exercise program selections, and enter user setup data for the console to zero... Low speed. Incline
The INCLINE display field shows the treadmill incline in the workout. Pulse
The Pulse display field shows the heart rate in each Operations mode. Contact your workout...
Assembly and Owner's Manual - Page 24
... during Workout Mode. Then you make a selection from the Program Selection menu. • Set your selection of data values for user setup or exercise program setup.... change when you press 2, the treadmill speed adjusts to 2 mph (or 2 km/h). Push the ENTER/RESET key 2 times.
For example, if you set the selection. SPEED ▲ / ▼
2%, 4%, 6%, 8% [Preset Incline Keys] 2, 4, 6, 8 [...
Assembly and Owner's Manual - Page 25
...fit snugly and comfortably against your doctor before using a wireless chest strap or other telemetric heart rate monitor.
If you monitor your heart rate at any time during your workout. Attach the transmitter to the Console.
Contact Heart Rate (CHR) sensors are installed to control the intensity of your exercise... is included with the model 860 treadmill only. The Console shows your...
Assembly and Owner's Manual - Page 27
... (keep within this range for optimum fat burning)
Age
Exercise Programs
Schwinn® 840 Treadmill Quick Start (Manual Program) Profile Programs:
• 2 Course • 2 Circuit • 2 Pursuit
Calorie Goal 5K Course 10K Course 1 Custom User Program Heart Rate Controlled:
• Target HR
Schwinn® 860 Treadmill
Quick Start (Manual Program) Profile Programs:
• 3 Course •...
Assembly and Owner's Manual - Page 28
...ENTER...incline, press the Incline ▼ (Down) key.
Turn the Power Switch on or off immediately for the Manual Program. Start the treadmill at the bottom of the treadmill to the On position...User Setup section of this manual.
Stop exercising if you can push at any time during...you to go to Quick Start Mode or Program Setup Mode.
4. The console display counts down for 3...
Assembly and Owner's Manual - Page 30
... data, push the STOP key and hold for 3 seconds, or push STOP and ENTER/RESET. Or you can push the QUICK START key to your workout selection, no workout...treadmill adjusts as shown in a range of 10:00-99:00.
You can manually adjust the speed.
Course #1 You set the maximum incline, and the treadmill adjusts as shown in the Program Selection menu. Course #3 (model 860 only)
The Incline...
Assembly and Owner's Manual - Page 31
... shown in this profile. Circuit #2 You set the maximum incline, and the treadmill adjusts as shown in these profiles.
Pursuit #2 You set the maximum incline, and the treadmill adjusts as shown in the Program Selection menu. Pursuit #3 (model 860 only)
The Incline profile shows in this profile. Incline
Speed
31 You can manually adjust the speed. Circuit...
Assembly and Owner's Manual - Page 32
...Schwinn® 860 treadmill. The program monitors your Custom User program profile. Note: The Heart Rate Zone programs are a percentage of the maximum heart rate calculated from your age and other information in your user profile. For more detailed information about fitness zones, please refer to start program setup. Or you can push ENTER...with custom values for MAX Incline, and push the QUICK ...
Assembly and Owner's Manual - Page 34
... before cleaning, maintaining or repairing this machine.
The components are tight.
Wipe the treadmill down after 50 hours-Lubricate the walking belt. Only manufacturer supplied components can be ...To clean the walking belt, carefully turn the treadmill back to adjust the tension.
This Notice is necessary to the upright position. Make sure all dirt and salt from service ...
Assembly and Owner's Manual - Page 36
... comes first.
Folding the Treadmill
1. We also recommend a periodic inspection of your machine.
7. Moving and Storage
The folding mechanism on your local specialty fitness dealer
or Nautilus, Inc.... no object to clean.
2. Switch off any excess lubricant from the fully folded position.
3.
Put both arms. Do not use the following instructions:
1. Belt friction can...
Assembly and Owner's Manual - Page 37
...of the movement path of movement path in the folded position. Unfolding the Treadmill
1.
Do not connect the power cord or try to spill or cause blockage from the ...fully unfolded position.
3. Make sure that it to lay the treadmill down. Carefully pull back on each side.
Keep a minimum clearance behind the machine...
Assembly and Owner's Manual - Page 39
...the movement path of measure. (English/Metric) Safety key
Solution
Make sure AC outlet functions correctly. Make sure the power...Console. (See Emergency Stop Procedure in the "ON" position. Damage to make sure it does not hit other objects...treadmill can damage the Console operation.
6.
Do not use , refer to the "Unfolding the Treadmill" procedure in
Display set to lift or move the treadmill...
Similar Questions
860 When Turned On Shows Safe Key Lockout...remove And Replace Safe Key Makes No
(Posted by dhlester 1 year ago)
Treadmill Stops After 10-15 Seconds Schwinn 830
I checked the speed sensor as far as position, looks good. Sprayed silicone spray under belt. Can tu...
I checked the speed sensor as far as position, looks good. Sprayed silicone spray under belt. Can tu...
(Posted by dannygolf56 1 year ago)
Schwinn 870 Incline Program Issue
Schwinn 870 - incline is not moving. Program shows 15 for incline and will not change. During calibr...
Schwinn 870 - incline is not moving. Program shows 15 for incline and will not change. During calibr...
(Posted by tsmithuv 1 year ago)
How Do I Unfold The Arm Of The Treadmill So I Can Use It
My treadmill is folded and I can't remember how to unfold it
My treadmill is folded and I can't remember how to unfold it
(Posted by pmck63 9 years ago)
840/860 Treadmill Squeaking
i would like to know how to fix the squaeking on a 840/860 model treadmill ..it is only 6 months old
i would like to know how to fix the squaeking on a 840/860 model treadmill ..it is only 6 months old
(Posted by wmarkby 9 years ago)