Home » Samsung » Projection Televisions » Samsung HLS5665W

Samsung HLS5665W Support Question

Find answers below for this question about Samsung HLS5665W - 56" Rear Projection TV.
Need a Samsung HLS5665W manual? We have 2 online manuals for this item!

Samsung Overview Questions Manuals Reviews Videos Research

Question posted by jupiter35 on April 21st, 2012

I Have A Samsung Hl-s5665w And It Turns Off After A Few Seconds. What Is The Pro

what is the problem?can i fix it?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by jupiter35 on April 21st, 2012 4:48 PM

This answer was accepted by the poster of the original question.

jupiter35

Member since:
April 21st, 2012

Points: 50

1,100
points

ballast has a capacitor that burst.changed the ballast and works fine.

Answer #2: Posted by nightbird50 on September 5th, 2012 1:39 PM

nightbird50

Member since:
September 5th, 2012

Points: 0

100
points

If capacitors on power-supply are ok, check a 470 volt-47uf capacitor on small board next to the lamp.If top is raised it needs to be replaced with same

Answer #3: Posted by TVDan on April 21st, 2012 1:39 PM

TVDan

Member since:
August 8th, 2011

Points: 4,732,000

90
points

Normally this is an indication that you have a bad lamp, but really what this indication is, the microprocessor has not received the signal from the optical engine that "the lamp is lit and all is well". There are many things that need to happen before the lamp will start up. The power supply must develop all the needed voltages required by all the rest of the circuits, the cooling fans must be running at the correct speeds, the lamp door switch must be closed (interlock switch), The Color Wheel must be able to spin at the 1800 RPM and lock in sync with the video signal, the ballast circuit must be able to develop the 5000 volts to start-up the mercury vapor lamp, and the lamp needs to be in good working condition to light up. There should be no weird noises pointing to the fact that a fan or the color wheels motor bearings are starting to go bad. The normal failures are the lamp and the color wheel. Unfortunately there is NO way to test a lamp. I have seen nearly 100 lamps come into my shop that has failed in less than a month, and many that didn't last one full day. These lamp you buy off the web are many times factory seconds. I have had some customers send back a lamp two, three, and four times before they got one that lasted through the warranty. Our shop only buys from the manufacturer. When you turn on this DLP HDTV the fans will start up first and then the color wheel will spin-up. If the color wheel doesn't get up to the 1800 RPM and maintain that speed then the lamp will not get to enable pulse. unfortunately after three attempts the set will shut down and the indicators will blink telling the customer to change the lamp, and of course after the customer does it, the problem remains the same. The microprocessor is located in the signal cluster and all it knows is that the lamp didn't light up correctly, so it gives the change lamp LED indicator blink

TV Dan

Related Samsung HLS5665W Manual Pages

Open Source Guide (ENGLISH) - Page 1

... of the whole must be distributed under the Freetype Project. Thus, it clear that distribution is intended to ...distribution conditions are outside its recipients to address new problems or concerns. If distribution of executable or object ...conditions for questions regarding open sources, contact Samsung via Email (vdswmanager@samsung. You may add an explicit geographical ...

Owner Instructions - Page 1

Register your product at www.samsung.com/global/register Owner's Instructions HL-S4265W HL-S5065W HL-S5665W HL-S6165W HL-S6765W HL-S5055W This device is a Class B digital apparatus.

Owner Instructions - Page 2

... (480p) video. 480i programs are now broadcast with DD 5.1 soundtracks. Several of our current analog TV programs, while the 480p format offers improved image detail over 480i. The first is Standard Definition Television (SDTV) and the second is a new way of Dolby digital audio formats from Dolby Surround 2.0 to your home audio system...

Owner Instructions - Page 4

...Rear Panel Jacks ...12 Remote Control...13 Connections 16 Connecting VHF and UHF Antennas 16 Antennas with 75-ohm Round Leads 16 Connecting Cable TV... or S-Video/Audio jack 19 Connecting a Second VCR to Record from the TV 19 Connecting a Camcorder 20 Connecting a DVD... to an Analog Amplifier 24 Operation 26 Turning the TV On and Off 26 Plug & Play ...56 LNA (Low Noise Amplifier 57 English - 4

Owner Instructions - Page 9

... channel tuning for up to 181 channels • A special filter to reduce or eliminate reception problems • Fine tuning control for the sharpest picture possible • A built-in multi-channel sound... that you can access from right side buttons or remote control • Automatic timer to turn the TV on -screen menu system you have all the parts shown here. In addition, it has...

Owner Instructions - Page 11

.... You'll occasionally hear it working. HL-S4265W/HL-S5065W/HL-S5665W/HL-S6165W/HL-S6765W HL-S5055W POWER Press to keep the inside the set is Off TIMER LAMP STAND BY/TEMP Indication Standby state. A cooling fan inside lamp from overheating. Lamp may be turned on in about 30 seconds for the TV to warm up, so normal brightness...

Owner Instructions - Page 13

...page 81) 20. Mode (TV/DVD/STB/CABLE/VCR) Selects a target device to a particular channel. 3. POWER Turns the TV on -screen menus, press ENTER... Press to directly tune to be controlled by the Samsung remote control (i.e., TV, DVD, STB, CABLE, or VCR). P.SIZE ... to select "AIR" or "CABLE". 5. MTS (Multichannel Television Stereo) Press to select additional channels (digital and analog) being...

Owner Instructions - Page 18

...Connect the last coaxial cable between the other OUT terminal on the splitter and the A-IN terminal on the TV. Set the A/B switch to the "B" position to view scrambled channels. (When you set the A/B switch... set the A/B switch to the Cable box's output channel, which you can buy from your Samsung dealer or any electronics store). 1 Find and disconnect the cable that Descrambles Some (But Not ...

Owner Instructions - Page 19

...match the color coded input terminals and cable jacks. TV Rear Panel 2 Connect a set of audio cables between the AUDIO OUT jacks on the TV and the AUDIO input jacks on the VCR. Incoming ...- 19 Incoming Cable or Antenna Stereo VCR Connecting a Second VCR to Record from the TV 1 Connect a video cable between the VIDEO OUT jack on the TV and the VIDEO input jack on the VCR. Connecting ...

Owner Instructions - Page 26

...Plug & Play function operates after several seconds, even if the ENTER button is displayed. • The Language menu will automatically appear after plugging in the TV for the first time. 1 Press ... connected status of the antenna is connected to memorize the channels of the OSD. Operation Turning the TV On and Off Press the POWER button on the front panel. or † button to...

Owner Instructions - Page 34

... Players, VCRs, Cable boxes, and Set-Top Boxes. If your VCR does not turn on if your TV's volume. Operation Customizing Your Remote Control After it has been set up properly, your... the remote control allows you to Operate Your VCR 1 Turn off your VCR. 2 Press the VCR button on your TV's remote control. 3 Press the SET button on your TV's remote control. 4 Using the number buttons on your remote...

Owner Instructions - Page 35

... cable box code listed on page 39 of this manual for your cable box does not turn on if your TV's volume. English - 35 Make sure you enter three digits of cable box. Your cable box should turn on the remote control. Note on Using Remote Control Modes: Cable Box When your remote...

Owner Instructions - Page 36

... Note on if your remote is set -up correctly. English - 36 If your DVD does not turn on Using Remote Control Modes: DVD When your remote control is listed, try each code, 000 through...Operation Setting Up the Remote to Operate Your DVD 1 Turn off your DVD. 2 Press the DVD button on your TV's remote control. 3 Press the SET button on your TV's remote control. 4 Using the number buttons on ...

Owner Instructions - Page 37

If your STB does not turn on if your TV's volume English - 37 Note on Using Remote Control Modes: STB When your remote control is in "STB" mode... brand of STB. Setting Up the Remote to Operate Your Set Top Box 1 Turn off your STB. 2 Press the STB button on your TV's remote control. 3 Press the SET button on your TV's remote control. 4 Using the number buttons on your remote control, enter three...

Owner Instructions - Page 39

...042 043 022 036 016 016 032 033 034 019 021 023 028 046 017 029 035 037 045 SAMSUNG SET-TOP BOX Product Ground wave STB Satellite STB CABLE STB STB DVD COMBO Satellite STB HDD COMBO ...014 SET-TOP BOX Brand Code ALPHASTAR 023 ANAM 043 CHANNEL MASTER 018 034 CROSSDIGITAL 019 CHAPARRAL 035 DIRECT TV 015 016 017 019 022 045 060 061 062 065 066 067 068 DAEWOO 074 DISH NETWORK SYSTEM ...

Owner Instructions - Page 40

Operation Remote Control Codes SAMSUNG DVD Product DVD DVDR BD Record VCR COMBO VCR Record DHR COMBO Code 000 001 002 003 004 005 006 007 008 009 010 011 ...

Owner Instructions - Page 45

... press the ENTER button. • When you can be selected only when the external device is turned on the AV1 remote control repeatedly to the TV. NOTES • Only connected devices can be selected. • Before selecting an input source,... "AV1", "AV2", "S-VIDEO1", "S-VIDEO2", "COMPONENT1", "COMPONENT2", "PC", "HDMI1", or "HDMI2" on the TV's rear panel and "AV3"or "S-VIDEO3" on the...

Owner Instructions - Page 114

... minutes before lamp replacement 1. After replacing the lamp, the screen quality will be replaced periodically. Turn the power off and wait for the lamp, give the code number to the store where you purchased the TV or to a Samsung Service center. • Caution 1. Appendix Replacing the Lamp • Why do I need to an...

Owner Instructions - Page 116

... is broadcasted in model only.) • The display panel used for 30 seconds, then try this list of digital channels vary. Picture rolls vertically. Check all...Samsung authorized service center. Make sure the MUTE button is plugged in . Appendix Troubleshooting If the TV seems to Set Top Box built-in color. Problem Poor picture quality. Digital broadcasting screen problem...

Owner Instructions - Page 117

...TV on the TV. Cabinet • Never open the cabinet or touch the parts inside of the cabinet. • This DLP TV projects...26 x 37.87 inches 56.93 x 18.37 ...HL-S4265W HL-S5065W HL-S5665W HL-S6165W HL-S6765W HL-S5055W Voltage AC 110-120V AC 110-120V AC 110-120V AC 110-120V AC 110-120V AC 110-120V Frequency of the different television systems that spill into it might cause a problem...

Samsung Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

General Support
Samsung's 1080p DLP TVs are 1080p30. That is, 1080p at a rate of thirty (30) frames per How Many Frames Per Second (FPS) Do Samsung DLP TVs Display? Current Samsung DLP TVs display at 30 fps (frames per second.
Using Anynet+ With A Home Theater SAMSUNG
... these steps: Connect an HDMI cable between the TV (HDMI in on the rear of the Anynet+ Home Theater (HT-AS720ST) HDMI connections on the rear of the Anynet+ Television (LN40750) connections on the rear of the Anynet+ Home Theater (HT-AS720ST) connections on the rear of the Anynet+ Television (LN40A750) HDMI When you...
Using Anynet+ With A Home Theater SAMSUNG
... the Tools Menu. How To Use The Wireless LinkStick With Your Television 15174. Product : Televisions > LCD TV 2317. How To Use Film Mode return the audio and audio control to the television, follow these steps: the Tools button on the TV's remote to the TV and the Vol. + and - Returning The Audio And Audio Control...