Ryobi WS722 Support Question
Ryobi WS722 Support Question
Find answers below for this question about Ryobi WS722.Need a Ryobi WS722 manual? We have 1 online manual for this item!
Question posted by Anonymous-165466 on May 15th, 2019
Riving Knife Issue's
I am having issue's with my tile binding up on the riving knife. I have tried adjusting it by loosening the screws and aligning. I have tried tweaking a bit still nothing. Any suggestions?
Current Answers
Answer #1: Posted by hzplj9 on May 15th, 2019 2:30 PM
hzplj9
Member since:
June 25th, 2012 Points: 4,875,710
Member since:
June 25th, 2012 Points: 4,875,710
Not sure what you mean by 'riving knife'. I assume you are referring to the blade or is it the rising cover that protects you from the blade? I would suggest taking the time to maybe return to the assembly instructions and check that everything has been attached as per the instructions. These devices are very simple in operation and providing the blade is fixed firmly and that the protector will rise and fall with the tile going through you should not experience any issues. If the guide bar is causing you an issue there is a knack to getting it to stay on the bed correctly and getting it straight can be a problem. I have attached a link to the user guide which should help in solving your dilemma.
https://www.manualslib.com/manual/1111767/Ryobi-Ws722.html
Good luck. Hope that helps.
Related Ryobi WS722 Manual Pages
User Manual - Page 2
... the tool or attachment to determine that it will draw. If in doubt, use , before turning it was not designed for alignment of moving parts, binding of ...tool before servicing, or when changing attachments, wheels, bits, cutters, etc., all instructions listed below, may risk injury.
NEVER STAND ON TOOL. These cords are recommended when working order.
REMOVE ADJUSTING...
User Manual - Page 3
... understood or if in . (178 mm). BEFORE MAKING A CUT, BE SURE ALL ADJUSTMENTS ARE SECURE. NEVER TOUCH WHEEL or other moving .
WHEEL COASTS AFTER BEING TURNED...AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could ignite fumes. INSPECT TOOL CORDS PERIODICALLY. aged, have the proper outlet installed by an authorized service center to free ...
User Manual - Page 5
...can support one power tool may be able to disconnect.
English Only round jacketed cords listed by Underwriter's Laboratories (UL) should be used for the tile saw does not operate...120 volt circuit and has a grounding plug similar to result in a shop is for outside use tool with this measure of safety.
5 -
ELECTRICAL
EXTENSION CORDS
Use only 3-wire extension cords that have ...
User Manual - Page 6
...60 Hz, 4.8 Amps No Load Speed 3,450 r/min. (RPM)
KNOW YOUR TILE SAW
See Figure 3, page 12. Before use the tool. tile cutting wheel is inaccessible to children and others not qualified to use of this product...or the connector if an extension cord is fully adjustable for diagonal cuts and miter cuts. A 7 in .
The miter guide is fully adjustable for making cross cuts and using the bevel ...
User Manual - Page 7
...not operate this tool. The double "D" flats on the wheel washers align with this tool until the parts are going in serious personal injury.
Inspect the tool carefully to ...; Hold arbor wrench firmly to loosen. Remove arbor nut, outer wheel washer, and cutting wheel.
7 -
PACKING LIST Tile saw is complete. Either of this tool or create accessories not recommended for...
User Manual - Page 8
...; Install the screws into your eyes, resulting in possible serious injury. NOTE: Always adjust splash hood horizontally.... Align splash hood with clean tap water. ...tools to desired angle using the rip
guide scales, located on bottom of cut man-made tile, pavers, natural stone products, and stone tile products only.
8 -
To change reservoir water: Unplug tile...
User Manual - Page 9
... grease pencil, mark the area to be cut is not in use by twisting the tile. Wait for making bevel cuts, whenever possible.
To adjust angles: Slide miter guide onto rip guide. Adjust to start the tool. MAKING CUTS
Always draw the line to turn the switch OFF and remove the switch...
User Manual - Page 10
... guide and slide miter guide along one of the marks. L-cuts are cuts that remove a piece of tile to fit in a corner, around a cabinet, or a piece of molding and are used for the... of the material. Wait for cross cut on material.
Slide miter guide onto rip guide.
Adjust miter guide to desired angle, using the bevel table.
Using a marker or grease pencil, mark the area...
User Manual - Page 11
...into your exposure, work . English GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. TILE CUTTING WHEEL
For maximum performance and safety, it is recommended that are available at... your saw. Some examples of the same high quality are specially designed to do this tool.
cutting wheel provided with a sufficient amount of high grade lubricant for the life of...
Similar Questions
My Tool Is Stuck In Cycle Mode The Fault Light Is Blinking And Won't Work
my crimper is stuck in cycle mode and fault light is blinking and tool won't work now
my crimper is stuck in cycle mode and fault light is blinking and tool won't work now
(Posted by Anonymous-174283 10 months ago)
Ryobi Rts10 Riving Lever Won't Lock
The riving knife lever on Ryobi RTS10 won't lock. Is there anything that shows the assembly of this ...
The riving knife lever on Ryobi RTS10 won't lock. Is there anything that shows the assembly of this ...
(Posted by nsmerk 8 years ago)
Chain Cover Issues On Ryobi 10519
chain adjustment difficult to make work. screw doesn't move. If you get it to work chain loosens or ...
chain adjustment difficult to make work. screw doesn't move. If you get it to work chain loosens or ...
(Posted by Ricam 8 years ago)
How Do You Remove The Key On The On/off Switch?
I assembled my ws722 but I can't get the on/off switch to work. I assume this is because the red key...
I assembled my ws722 but I can't get the on/off switch to work. I assume this is because the red key...
(Posted by suarts811 9 years ago)
Charger Has Green Light But Will Not Operate Any Of My Tools
riboyi lithium 18v P103 battery has a green light from charger but will not run andy of my tools
riboyi lithium 18v P103 battery has a green light from charger but will not run andy of my tools
(Posted by jmschaefer 12 years ago)