Ryobi TSS120L Support Question
Ryobi TSS120L Support Question
Find answers below for this question about Ryobi TSS120L.Need a Ryobi TSS120L manual? We have 4 online manuals for this item!
Question posted by mikemcgrath on December 18th, 2019
How To Realign Blade With Throat Plate?
I dropped my Ryobi TSS120L while trying to attach it to the stand it came with. Plastic handle as well as knob that allows saw to release and turn for miter both broke.Now blade does not sit inside of opening of throat instead it is slightly to 1 side and cut into top of throat.How can i align the blade to opening in throat?Thank You!!!
Current Answers
Answer #1: Posted by hzplj9 on December 23rd, 2019 2:57 AM
hzplj9
Member since:
June 25th, 2012 Points: 4,873,510
Member since:
June 25th, 2012 Points: 4,873,510
Refer to page 19 of the user guide available from this link:
https://www.manualslib.com/manual/1208184/Ryobi-Tss120l.html
It explains how align the base. Check for any bent or damaged parts before attempting adjustments.
Related Ryobi TSS120L Manual Pages
User Manual - Page 3
...BLADE PATH IS FREE OF NAILS. Do not force the tool or attachment to do the job better and safer at all instructions listed below, may result in injury.
NEVER STAND ON TOOL...TOOL dry, clean, and free from oil and grease. TURN THE POWER OFF. Never use blade washers or blade bolts that are doing and use of the tool... leave tool until it is safer than using your saw is ...
User Manual - Page 4
... together may cause burns or a fire.
under the influence of blade pinching and kickback. avoid contact. SPECIFIC SAFETY RULES
FIRMLY CLAMP OR BOLT the tool to lock. Lock the miter table by securely tightening the bevel lock knob.
Use this saw table at approximately hip height.
KEEP HANDS AWAY FROM CUTTING...
User Manual - Page 5
... cutting path with the path of the saw blade.
ALWAYS release the power switch and allow the saw blade to stop rotating before changing blade or servicing.
ALWAYS carry the tool only by the carrying handle.
This saw can tip over if the saw head is released suddenly and the saw on and off tool and wait for any use to...
User Manual - Page 6
... involve your hands away from the blade will allow you to rain or use in serious ...personal injury.
Read Operator's Manual Eye Protection
To reduce the risk of risk associated with this tool. Always wear eye protection with ANSI Z87.1.
Some of these symbols will result in damp locations.
Wet Conditions Alert
Do not expose to operate the tool...
User Manual - Page 7
...by the workpiece being dropped into the blade or being done.
Worktable Surface where...turns completed by the blade in a workpiece that can occur when the blade binds or stalls, throwing the workpiece back toward the front of the saw blade tooth is bent (or set) outward from the blade. Riving Knife/Spreader/Splitter (flooring and table saws) A metal piece, slightly thinner than 90°.
Miter...
User Manual - Page 8
... lumber sizes 1-1/2 in . Miter Lock lever
BLADE WRENCH
Dust BAG
Upper Blade Guard
"D" handle
switch lock
Switch Trigger
laser guide
Bevel Lock Knob
Lower blade guard
"NO HANDS ZONE" BOUNDARY LINE
45 30 33.9 15
0
1
2
3
4
5
"NO HANDS ZONE" LABEL
bevel scale
miter fence
base
45
MITER TABLE WORK CLAMP
8
Miter Scale
throat plate
Fig. 1 x 3-1/2 in .
Blade Diameter 7-1/4 in...
User Manual - Page 9
... shock-resistant, seethrough plastic that provides protection from the tool, then lower the saw from rotating. To transport, turn off and remove the battery pack from each side of the saw has been provided to hold the lock button while installing, changing, or removing blade.
9
BEVEL LOCK KNOB
The bevel lock knob securely locks your miter saw at the rear...
User Manual - Page 10
... the switch trigger. Switch lock
Switch trigger
Padlock
TOOLS NEEDED
45 30 33.9 15
123 4 567
The following tools (not included) are needed for making adjustments or installing the blade:
Fig. 4
FRAMING Square
combination Square Fig. 5
10 To prevent unauthorized use of the compound miter saw will not start until you depress the switch lock...
User Manual - Page 12
... this product with the saw without checking for interference between the blade and the miter fence.
Damage could result in the down on the top of the saw. Use of a product...the tool.
The saw is released suddenly. To release the saw arm, push down position. Parts on a level work surface or stand.
Remove the screws from the rear bracket/carrying handle and...
User Manual - Page 15
ASSEMBLY
To Install/replace the Blade
See Figures 11 - 12. Larger blades will come in figure 12.
Replace outer blade washer. Turn blade
bolt clockwise to tighten. Double "D" flats on blade washers align with an arrow on spindle.
Depress spindle lock button and replace blade bolt. The direction of the saw blade inside lower blade guard and onto spindle. and...
User Manual - Page 16
... pack from the tool. Push down to lock the miter table.
Lay a square flat on the saw arm and pull out the lock pin to
release the saw arm.
Raise the saw arm.
Lift the miter lock lever.
Rotate the miter table until the square and throat plate are needed.
Using the blade wrench provided...
User Manual - Page 17
... as shown in figure 17. If the front or back edge of the saw blade angles away from the tool. Pull the saw arm all the way down to lock the miter table. Lay a square flat on the miter table. Slide the other leg of the square against the fence. Place one on...
User Manual - Page 18
... part of the saw blade, not the blade teeth.
Rotate the blade by hand and check the blade-to-table alignment at several points.
The edge of the saw blade angles away from the tool. Pull the saw arm all the way down to lock the miter table.
Loosen bevel lock knob and set saw arm at both...
User Manual - Page 20
... or cutting plastic, use . The blade could result in movement of this warning can result in .
TO REMOVE BATTERY PACK
See Figure 25. Locate latches on battery
pack with groove inside saw to a workbench or an approved workstand.
DEPRESS LATCHES TO RELEASE BATTERY PACK
WARNING:
To avoid serious personal injury, always lock the miter lock...
User Manual - Page 21
... the pointer aligns with zero
on the miter scale.
WARNING:
NEVER move the workpiece or make adjustment to any cutting angle while the saw arm to be recharged. To Cross cut is placed against the fence. If the tool stops during use, release the trigger to prevent the blade from binding in workpiece. If the...
User Manual - Page 28
... miter saw blade to the up position by at the factory for interference between the blade and the throat plate. PIVOT ADJUSTMENTS
Note: These adjustments were made , it strikes the throat plate during operation of alignment during shipping. Damage could cause serious personal injury, always remove the battery pack from the tool.
Loosen the bevel lock knob by turning the knob...
User Manual - Page 29
... of
scrap wood. Turn the saw on and make a slight cut to score the wood. Release the switch trigger and allow the saw blade to
stop rotating before raising the saw arm. Using a padlock, lock the switch trigger to make the saw blade to move the miter table.
Prior to your nearest Ryobi Authorized Service Center for repair...
User Manual - Page 32
...handling. • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products and, • arsenic and chromium from exposure to these chemicals varies, depending on a plate attached...work . The model number of this tool will be found on how often ... Cordless Compound Miter Saw
P551
WARNING: This product and some dust created by Ryobi Limited.
988000...
User Manual 4 - Page 4
... MITER SAW - Key Nos. 18 and 44 1
44 080001020901 Data Label 1
45 089100207027 Screw (M3, Shoulder 1
46 089240001064 Screw (M5 x 5 mm, Shoulder 1
47 A19001040091 Screw (M4 x 9 mm, Pan Hd 1
48 080001020708 Lower Blade Guard Assembly
(Inc. MODEL NUMBER P551
The model number will be found on a label attached to the motor housing. COMPOUND MITER SAW or...
User Manual 4 - Page 6
...MITER SAW or when ordering parts. Key Nos. 48-49 1 No Hands Label 2 No Hand Label 2 Steel Ball (8 mm 1 Compression Spring 1 Screw (M5 x 18 mm 2 Wear Ring 8 Miter Lock Tip 1 Plug 1 Miter Lock Shaft 1 Miter Lock Lever 1 Spring 1 Screw (M5, Shoulder 1 Work Clamp 1
089240001015 Miter Pointer 1
6 RYOBI...Washer (M8 3 Screw (M4 x 8 mm 5 Throat Plate 1 Lock Nut (M8 1 Washer (ID8.2 x...
Similar Questions
Replacement Part Throat Plate For Rts23 10 Inch Table Saw Ryobi
looking to purschane throat plate for a ryobi rts23
looking to purschane throat plate for a ryobi rts23
(Posted by gmaashley57 2 years ago)
Ryobi 10" Table Saw Dado Throat Plate
where can I find a dado throat plate for the Ryobi 10" table saw?
where can I find a dado throat plate for the Ryobi 10" table saw?
(Posted by Rick52757 2 years ago)
What Is The Part Number For The Ryobi Tss 120l ' Bevel Pivot'?
What is the part number for the Ryobi TSS 120L " Bevel Pivot"?
What is the part number for the Ryobi TSS 120L " Bevel Pivot"?
(Posted by dayoneskateshop 7 years ago)
Ryobi Rts30 Dado Throat Plate And Dado Blade
I am looking for the correct dado throat plate and dado saw blades for my Ryobi RTS30 10" table saw....
I am looking for the correct dado throat plate and dado saw blades for my Ryobi RTS30 10" table saw....
(Posted by daleemcmillan 12 years ago)
Ryobie Dado Throat Plate Part Number 089037008711
Where can I get the RTS30 table saw dado throat plate number 089037008711 and for how much? RRW
Where can I get the RTS30 table saw dado throat plate number 089037008711 and for how much? RRW
(Posted by wurzb 12 years ago)