Ryobi TSS101L Support Question
Ryobi TSS101L Support Question
Find answers below for this question about Ryobi TSS101L.Need a Ryobi TSS101L manual? We have 4 online manuals for this item!
Question posted by dtwood1 on August 12th, 2012
Ryobi Tss101l Won't Start.
My 10" mitre saw is getting electricity to the switch and when I pull the trigger the current returns in the white wire but I still can't get any movement out of the saw. The grey wire doesn't seem to have any current upon pulling trigger, I'm guessing it's a switch issue? Everything else seems to work.
Current Answers
Related Ryobi TSS101L Manual Pages
English Manual - Page 2
...the design of this product making its RYOBI® power tools with the original product. HOW TO GET SERVICE: Just return the power tool, properly packaged and postage prepaid, ... Specific Safety Rules...4-5 Symbols...6-7 Electrical...8 Glossary of Terms...9 Features...10-12 Tools Needed...12 Loose Parts List...13 Assembly...
English Manual - Page 3
.... Do not let visitors contact tool or extension cord while operating.
MAKE WORKSHOP CHILDPROOF with padlocks, master switches, or by preventing body contact...TOOLS WITH CARE. For example: pipes, radiators, ranges, refrigerator enclosures.
KEEP GUARDS IN PLACE and in electric shock, fire and/or serious personal injury. If in damp or wet locations or expose to carry the current...
English Manual - Page 4
...tool's plug.
DO NOT MODIFY the plug provided. Always use brake fluids, gasoline, petroleum-based products, or any medication.
When servicing use a clamp to prevent the saw or workpiece before starting cut , be plugged into a three-hole electrical...TOOL IF SWITCH... electrical devices: 3-wire...saw table at a time. The maximum blade capacity of accessories that is 10...
English Manual - Page 5
...switch and allow the saw blade to a complete stop rotating before changing blade or servicing. Do not allow the saw blade to come to loosen and could cause the saw blade to stop . f) Turn off tool and wait for any electrical component fail to cause a careless mistake. DO NOT pull the saw...the motor switch on the miter table and position it to avoid accidental starting when ...
English Manual - Page 6
...Current
Type of current
Direct Current
Type or a characteristic of current
no
No Load Speed
Rotational speed, at no load
Class II Construction
Double-insulated construction
.../min
Per Minute
Revolutions, strokes, surface speed, orbits etc., per minute
Wet Conditions Alert
Do not expose to operate the tool...following symbols may be used on this tool.
Safety Alert No Hands Symbol Hot...
English Manual - Page 7
... injury.
When servicing, use over eyeglasses or standard safety glasses with side shields.
Call Ryobi customer service for repair.
WARNING:
To avoid serious personal injury, do not attempt to ...INSTRUCTIONS
7
For service we suggest you return the product to use this product until you do not use this product. Before beginning power tool operation, always wear safety goggles or ...
English Manual - Page 8
... electric cord having an outer surface that has an outlet like the one power tool may not be used.
**Ampere rating (on tool data plate) 0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length Wire Size (A.W.G.)
25' 16
16
16
16
14
14
50' 16
16
16
14
14
12
100' 16
16
14
12
10
-
**Used on direct current...
English Manual - Page 9
... for drilling large holes accurately.
Riving Knife/Spreader/Splitter (table saws) A metal piece, slightly thinner than the blade, which produces...of a workpiece by the blade in reference to blade movement. Snipe (planers) Depression made with the blade at ...90°.
Arbor The shaft on which a blade or cutting tool is being kicked back toward operator. Bevel Cut A cutting operation ...
English Manual - Page 11
...saw housing and ratcheting the lever. It will glide forward and backward the length of servicing. ELECTRIC BRAKE
An electric brake has been provided to quickly stop blade rotation after the switch is larger providing additional support. MITER FENCE
The miter fence on the tool...
10 in . The bevel lock lever is spring loaded and is released by pulling the lock pin away from the saw ...
English Manual - Page 12
... may be used. Spindle Lock Button
Switch trigger
Switch Trigger
Fig. 4
Padlock
TOOLS NEEDED
The following tools (not included) are needed for making adjustments or installing the blade:
Combination Wrenches (2) (10 mm, 12 mm)
HEX KEYS (3)...and lock the switch in .
FEATURES
slide lock knob
The slide lock knob locks and unlocks the sliding feature of the compound miter saw, disconnect it ...
English Manual - Page 14
... your back, and get help when needed. This saw has been shipped with this product until the parts are damaged or missing do not operate this tool. If shipping has influenced...have carefully inspected and satisfactorily operated the product. The saw is misuse and could result in accidental starting and possible serious personal injury. Hand pressure should be of the ...
English Manual - Page 22
... caution:
Do not start the compound miter saw to a workbench. ...saw without holding workpiece against the fence).
Failure to do not cut . The use one side of this warning can result in movement...tools to make adjustment to any cutting angle while the saw is running and the blade is rotating. Remember that a careless fraction of the accessory blades available from the Ryobi...
English Manual - Page 30
... to shift, all settings should first be tested on miter table.
changing one angle changes the other tool made.
Save left end of cut
Right side, inside corner
Fence
outside corner 1. Laying molding flat...of cutting crown molding than any other angle as well. In general, compound miter saws do not have angles of molding against fence 2. When cutting crown molding by this ...
English Manual - Page 33
...for
the positive stop adjustment screw), loosen the lock nut securing the positive stop use a 10 mm wrench and loosen the hex nut located on the miter scale. However, when the ...the miter table.
Note: These adjustments were made , it with the saw blade to the miter table support before starting the saw blade is located inside the miter table. Recheck blade-to maintain full cutting...
English Manual - Page 36
...obtain your exposure to these exposures varies, depending on how often you do this type of Ryobi Limited used under license.
987000-212 12-8-08 (REV: 03)
ONE WORLD TECHNOLOGIES, INC... at 1-800-525-2579. OPERATOR'S MANUAL
10 in a well ventilated area, and work with Laser
TSS100L
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities ...
Repair Sheet - Page 3
...10...Screw (M5 x 10 mm Flat Hd ...Pan Hd 2 Ground Terminal 1 Saw Blade 1 Blade Flange (45 ... x 10 mm 2 Motor Assembly 1 * Screw (M5 x 10 mm ...SAW w/LASER - MODEL NUMBER TSS100L
The model number will be found on a plate attached to the motor housing. Always mention the model number in .
NO. Extension Bar, Left 1 Screw (45 1 Clamp 2 Pivot Shaft 1 * Screw (M10 x 10... Screw (M4 x 10 mm Pan Hd 11 ...
Repair Sheet - Page 4
... (M4x12 mm Hexagon Socket 1 * Screw (M4 x 50 mm 1 Screw B (M6), for Link Plate 1 Elastic Pin (M5 x 10 mm 2 Cord Protection Tube A Grommet 1 Cable Bracket B 1 * Screw (M4 x 8 mm Hex Soc.
RYOBI 10 in all correspondence regarding your MITER SAW or when ordering repair parts. Hd 5
Tube 1 Dust Adaptor 1 * Screw (M4 x 12 mm Pan Hd 4 Pivot...
Repair Sheet - Page 5
...Adjustable Support Foot 1 Transformer 1 Handle Assembly 1 Laser Switch 1 Switch 1 * Lock Washer (M5 1 * Screw (M5 x 10 mm 1
KEY NO.
165 166 167 168 169 170...Terminal Block 1 Bend Relief 1 Power Cord Clamp 1 Male Connection w/Wire, for Laser Light..........1 Magnetic Ring w/Winding 2 Spring 1 Cord ...RYOBI 10 in all correspondence regarding your MITER SAW or when ordering repair parts.
Repair Sheet - Page 6
..., 175-177 and 188 1
Base Assembly (Not Shown) (Inc. RYOBI 10 in all correspondence regarding your MITER SAW or when ordering repair parts. SLIDING MITER SAW w/LASER - Key Nos. 60, 72, 74-81, 90-91...119, 155 166-169, 173 and 190-194 1
Slide Bar Guard Support Bracket Assembly (Inc. Key Nos. 2, 4-8, 10-12, 58-59, 68, 99, 127 and 185 1
Operator's Manual
* Standard Hardware Item - KEY
PART
NO....
Repair Sheet - Page 7
SLIDING MITER SAW w/LASER - RYOBI 10 in. MODEL NUMBER TSS100L
YELLOW LEAD
BRUSHES
SWITCH
BROWN LEAD YELLOW LEAD
YELLOW LEAD
BLACK LEAD
POWER CORD
MOTOR
WHITE LEAD
WHITE LEAD
WIRING DIAGRAM
Similar Questions
Ryobi 10" Table Saw Dado Throat Plate
where can I find a dado throat plate for the Ryobi 10" table saw?
where can I find a dado throat plate for the Ryobi 10" table saw?
(Posted by Rick52757 2 years ago)
Fence
Will the fence for the TSS101L fit on a TSS100L Ryobi mitre saw?
Will the fence for the TSS101L fit on a TSS100L Ryobi mitre saw?
(Posted by pcarneyconstruction 7 years ago)
Replacement Of Pad.on A Ryobi Rst #10 Table Saw.
The pad is located behind the knob that locks the blade swivel.
The pad is located behind the knob that locks the blade swivel.
(Posted by tabucher 11 years ago)
Needs Adjustment
I have a Ryobi 10in TSS101L compound miter saw. As I make a cut while it is zero'd out it continues ...
I have a Ryobi 10in TSS101L compound miter saw. As I make a cut while it is zero'd out it continues ...
(Posted by keitheburns 11 years ago)
Blade Not Going On Correctly
I recently bought the Ryobi mitre saw TSS101L used with no blade, turned it on seamed to work fine, ...
I recently bought the Ryobi mitre saw TSS101L used with no blade, turned it on seamed to work fine, ...
(Posted by shaunnyg2001 12 years ago)