Ryobi RTS30 Support Question
Ryobi RTS30 Support Question
Find answers below for this question about Ryobi RTS30.Need a Ryobi RTS30 manual? We have 4 online manuals for this item!
Question posted by fibb420 on December 10th, 2011
Install Kick Back Pawls Rts30
cant figure out how to put on this kickback pawls on table sawrts30
Current Answers
Related Ryobi RTS30 Manual Pages
English Manual - Page 4
...proper outlet installed by a qualified electrician. Keep TOOL dry,...tool when you are tired. Have defective switches replaced by a qualified service technician at approximately hip height.
NEVER OPERATE THE SAW ON THE FLOOR. GUARD AGAINST KICKBACK. Keep the blade guard down, the anti-kickback pawls... all fences and auxiliary tables before transporting saw or ...
English Manual - Page 5
...tool, loan them
frequently and use to the saw blade. SAVE THESE INSTRUCTIONS. Some examples of personal injury. Always use either hand for wide or long work using the table... work pieces.
Refer to cause cancer, birth defects or other users. c) Keeping spreader, anti-kickback pawls, and
blade guard in a well ventilated area, and work with approved safety equipment, such as...
English Manual - Page 8
... personal injury. Repair or replace a damaged or worn cord immediately. This tool is properly installed and grounded in accordance with a damaged cord since touching the damaged area could cause electrical shock resulting in figure 1. WARNING:
Check extension cords before each use tool with all local codes and ordinances.
Grounding Pin
120 V Grounded outlet
Fig...
English Manual - Page 9
... extend completely through cut without the workpiece being kicked back toward operator.
Resaw A cutting operation to... usually caused by the workpiece being dropped into the tool first.
Resin A sticky, sap-based substance that the...bevel angle.
GLOSSARY OF TERMS
Anti-Kickback Pawls (radial arm and table saws) A devise which, when properly installed and maintained, is designed to stop ...
English Manual - Page 11
... to the table saw table.
Located on the tool and in . SCALE - SWITCH ASSEMBLY -
The safe use of this handwheel to the sliding miter table at the desired cutting angle. ANTI-KICKBACK PAWLS - Bevel angles are attempting. The teeth on the anti-kickback pawls point away from the switch. BLADE GUARD - BLADE -
FEATURES
KNOW YOUR TABLE SAW
See Figure 2. A sturdy...
English Manual - Page 12
... front of the cabinet.
This action will prevent the tool from the switch and store in use by children and... assembly for all through the table and is used to be kicked back toward the operator and ...kickback pawls, and plastic blade guard. TO TURN YOUR SAW OFF:
Press the switch down .
Remove the switch key from accidentally starting , Always make sure your saw table...
English Manual - Page 15
... discard the packing material until you chose to remove the leg stand, the table saw base, lock washers, hex nuts, and the thickness of sufficient length to...tool. Mounting Holes
This tool comes mounted to the blade. After assembling it on the height/bevel adjusting handwheel.
Using a flathead screwdriver, turn the screw counterclockwise to install the Handle assembly
See Figure...
English Manual - Page 18
...into the table slot. Mount the miter fence to the front of the saw blade teeth must point down toward the front of the machine.
Assembly
TO check SAW BLADE installation
See Figure 12. caution...the larger blade wrench over the
hex nut. NOTE: Arbor shaft has left .
TO INSTALL miter FENCE
See Figure 13. Remove the miter fence from the miter fence storage on the arbor ...
English Manual - Page 19
ASSEMBLY
TO INSTALL BLADE GUARD ASSEMBLY
See Figure 14. TO INSTALL dust bag
See Figure 15. Slide the elbow inside the dust chute on the table saw . Slide the dust ...are in alignment.
NOTE: Blade alignment with side shields when operating tools.
Check the blade and spreader alignment. anti-kickback pawls
spreader
WING NUT
MOUNTING PLATE
Fig. 14 DUST CHUTE
ELBOW
DUST ...
English Manual - Page 20
...while making and woodworking NOTE: This table saw is properly installed and grounded according to use the anti-kickback pawls Cutting with a dull,...Fig. 16
20 warning:
Although many of this tool for clarity, do not operate the saw without the...Kickback can occur when the blade stalls or binds, kicking the workpiece back toward you with great force and speed. cutting aids
See Figure...
English Manual - Page 21
...make sure the blade guard and anti-kickback pawls are straight 90° cuts made...made with the grain of this tool. To avoid kickback while making
the cut . ...WARNING:
Always use blades rated less than 90°.
Cross cuts are in the wood) will be either rip cuts or cross cuts.
Cross Cut
WARNING:
Always make sure one side of cuts
See Figure...
English Manual - Page 27
... operator additional support for supporting wider workpieces.
operation
to use the table extension
See Figure 31.
to use OUTFEED SUPPORT
See Figure 30. To close: Push the table extension lever beneath the saw table
towards the back of the saw.
Push the table extension with both hands and pull it until it towards the...
English Manual - Page 29
...blade guard assembly is installed and working properly to ..., remove the switch key as shown in figure 37. Let the blade build ... WARNING:
Using the rip fence as saw table) behind
the saw for the cut on ...secure the angle, lock the miter fence in kickback which can cause serious personal injury. It is...blades rated less than the speed of this tool.
Always tighten the lock knob securely in...
English Manual - Page 30
... cut and securely lock the handle. Never push a small piece of injury should kickback occur. It is clear of the blade before turning on the saw for the cut
See Figure 37. WARNING:
Make sure the blade guard assembly is installed and working properly to move the wood through cuts.
Stand to...
English Manual - Page 31
... fence.
long, place a support
the same height as the table surface behind the saw off.
making a bevel cross cut
See Figure 41.
It is recommended that you place the piece to be...as it contacts the blade to the left
side of injury should kickback occur. WARNING:
Make sure the blade guard assembly is installed and working properly to the ON position. Push the bevel locking lever...
English Manual - Page 32
...fence.
making a compound (bevel) miter cut
See Figure 42.
WARNING:
Make sure the blade guard assembly is installed and working properly to avoid possible serious injury.
...the blade.
Wait for the blade to come to guide it from the table. It is recommended that you make a test cut on the miter fence... kickback occur. When the cut is made , turn the saw off .
English Manual - Page 33
...When the cut
See Figure 43. WARNING:
Make sure the blade guard assembly is a straight cross cut
See Figure 44. WARNING:
Never make freehand cuts (cuts without the blade guard installed. Non-through cuts can.... Make sure the blade guard assembly is essential to the sides as the top of the saw table behind the saw . Feed the workpiece into the blade.
When the work ...
English Manual - Page 34
...the arbor nut. Make sure the arbor nut is designed for this tool. WARNING:
Always use push blocks, push sticks, or featherboards when making dado cuts to 90°.... with your hands when making any non-through cut
See Figure 45. Remove the throat plate.
Raise the saw cannot be used .
Install dado throat plate. This saw blade. BLADE GUARD REMOVED
NON...
English Manual - Page 35
... NOTE: Arbor shaft has left hand threads. The table saw blade, raise the blade guard, and remove ...Do not start any adjustment, make sure the tool is unplugged from the blade and that all... nut over the blade arbor. TO REPLACe THE BLADE
See Figures 46 - 48. Unplug the saw.
... can occur if hands come in the OFF position. To install a standard blade: Place the new blade on ...
English Manual - Page 36
...the saw blade by turning the height/bevel adjusting handwheel counterclockwise.
Lift the anti-kickback pawls and place a framing square or straight edge against both the blade and spreader evenly with no.... ADJUSTMENTS
TO Check and Align the spreader, Saw Blade, and Blade Guard Assembly
See Figure 49.
framing square
blade
warning:
Before plugging the saw blade. The spreader must be ...
Similar Questions
How To Replace The Bevel Lock Washer On A Ryobi Rts30
(Posted by mike1QWJani 10 years ago)
Pawl Is Missing...
has the design changed or is mine missing the pawl assembly? it isn't in the box.
has the design changed or is mine missing the pawl assembly? it isn't in the box.
(Posted by yubsocool 11 years ago)
Ryobi Rts30 Dado Throat Plate And Dado Blade
I am looking for the correct dado throat plate and dado saw blades for my Ryobi RTS30 10" table saw....
I am looking for the correct dado throat plate and dado saw blades for my Ryobi RTS30 10" table saw....
(Posted by daleemcmillan 12 years ago)
Installing The Non-adhesive Sanding Paper For The S652d Hand Sander?
Please help with installing the non-adhesive sanding paper for the S652D hand sander. The instructio...
Please help with installing the non-adhesive sanding paper for the S652D hand sander. The instructio...
(Posted by mary64737 12 years ago)
Ryobie Dado Throat Plate Part Number 089037008711
Where can I get the RTS30 table saw dado throat plate number 089037008711 and for how much? RRW
Where can I get the RTS30 table saw dado throat plate number 089037008711 and for how much? RRW
(Posted by wurzb 12 years ago)