Ryobi RTS10 Support Question
Ryobi RTS10 Support Question
Find answers below for this question about Ryobi RTS10.Need a Ryobi RTS10 manual? We have 4 online manuals for this item!
Question posted by Dbaker85 on May 7th, 2014
Blade Stopping
I was recently given this table saw. Well shortly after turning it on the saw will make a sound and the blade stops. Any suggestions?
Current Answers
Answer #1: Posted by hzplj9 on May 8th, 2014 2:57 PM
hzplj9
Member since:
June 25th, 2012 Points: 4,875,670
Member since:
June 25th, 2012 Points: 4,875,670
Various issues can cause this. One could be that the blade is loose and the nut requires tightening. Check if the motor is stil running when the problem occurs, you should still hear it. If the motor stops it could be the motor has a faulty winding and would require replacement. There could also be a problem with the start/stop switch or even a faulty connection to the supply plug. Always disconnect from the supply before carrying out any maintenance, fingers are hard to replace.
Related Ryobi RTS10 Manual Pages
English Manual - Page 1
... of injury, the user must read and understand the operator's manual before using
this product. WARNING: To reduce the risk of rugged, trouble-free performance. Table Saw
BTS12S
Your table saw has been engineered and manufactured to our high standard for your purchase.
English Manual - Page 2
...reasonable time, but, in this product making its RYOBI® power tools with the original product. ADDITIONAL LIMITATIONS:... and may also have been given top priority in your RYOBI® power tool for a period of two years... case, within ninety (90) days or less. One World Technologies, Inc. table of contents
Introduction...2 Warranty...2 General Safety Rules...
English Manual - Page 3
....
Wear hearing protection during extended periods of parts, mounting and any tool.
USE RECOMMENDED ACCESSORIES.
Before further use , before turning it is in good working outdoors. It will draw. Make sure your product will do a job it was designed.
USE RIGHT TOOL. A wire gauge size (A.W.G.) of at the feed rate for outdoor...
English Manual - Page 5
... the cutting tool.
Use only recommended accessories listed in this tool, loan them frequently and use of saw blade. Instructions for any operation "freehand" which the blade cuts completely ...saw .
ALWAYS TURN OFF SAW before disconnecting it can result in which means using the table saw blade.
NEVER reach behind, over, or within three inches of the blade...
English Manual - Page 9
... The item on which a blade or cutting tool is angled rather than 90° to the fence.
GLOSSARY OF TERMS
Anti-Kickback Pawls (radial arm and table saws) A device which, when ...blade does not extend completely through the thickness of turns completed by a fence, miter gauge, or other than the blade, which the operation is designed to help keep the kerf open and also helps to make...
English Manual - Page 11
... is a metal device directly behind and above the blade.
The saw includes a rip fence and miter gauge. FEATURES
KNOW YOUR TABLE SAW
See Figure 2.
The safe use the tool.
11 The height of the blade is used to set with the blade adjusting handle on the front of the blade. Detailed instructions are designed to snag the workpiece...
English Manual - Page 12
... switch
button to start the tool.
Your table saw is intended to turn OFF.
WARNING:
In the event of this warning could result in use the 10 in., 24-tooth blade provided with your saw turned OFF, pull the switch key from accidentally starting , Always make sure your saw: With the saw . WARNING:
ALWAYS make sure the switch is not...
English Manual - Page 15
Hex Nut 16
I
F C
A. Upper Side Brace 2 B. Upper Brace 2 C. LOOSE PARTS LIST
The following items are included with the table saw leg stand: C
A G
B
E
D
H
J F
E B
E A
F
C
I
C
J
D
E
I
I
Fig. 3
F. Carriage Bolt (1/4-20 x 1-5/8 in 16 G. Carriage Bolt (5/16-18 x 5/8 in 4 H. Foot 4 J. Leg 4 D. Hex Nut 4 I. Lower Side Brace 2 E. Lower Brace 2
15
English Manual - Page 16
...possible serious personal injury. Add hardware and finger tighten.
Use the same steps to the blade. to install the lower braces.
Lower Brace
hex nut
foot
LEG
carriage bolt Fig. 6
16 If... Make sure the dimples on the leg align with the small holes on the brace.
Align the large holes on a level work surface. Inspect the tool carefully to make sure the table saw ...
English Manual - Page 17
... blade adjusting handle mounts to your back. ASSEMBLY
Mounting THE leg stand on the table saw base. Do not lift the saw base weighs approximately 42 lbs. Ignoring these precautions can occur during use.
Each of sufficient length to the floor before operating. Place the washer over the exposed end of the
rip fence making...
English Manual - Page 20
...; Cutting with a dull, gummed-up, or improperly set blades. Note: This table saw is sufficient to cut . Basic Operation of the TABLE Saw
The 3-prong plug must be caused by any attachments or ... following correct operating procedures Misusing the saw blade, they may use this tool for knots or nails before beginning a cut.
When making a cut, use of this manual. The ...
English Manual - Page 21
...blade other cuts are given later in place and working properly when making
each kind of the wood rides firmly against the miter gauge. WARNING:
Always use blades...to the blade. Make allowance for the wood as it comes
out of the wood. operation
types of this tool. Cross ...are made with an angled blade. Bevel cuts are made with the grain of the saw.
21 Be thoroughly familiar with...
English Manual - Page 25
Failure to heed this tool.
Wait for the blade to come to a complete stop before connecting to reduce the chance of injury should be saved on the left side of the blade and that you make a cross cut operations. Keep the miter gauge firmly against the saw table as it contacts the blade to a power source. Carefully check all...
English Manual - Page 26
... of the wood as the saw table) behind the saw ON by sliding it contacts the blade to reduce the chance of injury should be placed on the workpiece. When the cut is made , turn the saw for the blade to come to a complete stop before moving the
workpiece into the blade. operation
To make a RIP cut
See Figure...
English Manual - Page 34
Table Saw
BTS12S
WARNING:
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to ... well ventilated area, and work with approved safety equipment, such as those dust masks that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service Center. Your risk...
Repair Sheet - Page 3
...10 410012702 SCREW (1/4-20 x 3-1/4 in all correspondence regarding your TABLE SAW or when ordering repair parts. RRYYOOBBII TTAABBLLEE SSAAWW -- HD 1 32 089015001900 SCALE LABEL 1 33 0101010303 STRAP (Long 4 34 089015001701 MITER GAUGE ASSEMBLY....... 1 35 089015001700 RIP FENCE ASSEMBLY 1 36 A101141001 BLADE GUARD ASSEMBLY...... 1 37 412012714 WASHER (1/4 in 2 38...
Repair Sheet - Page 5
... 0101010302 OUTER BLADE WASHER 1
36 0101010920 ARBOR NUT (5/8-18 1
37 0101010312 ARBOR WRENCH (15/16 in all correspondence regarding your TABLE SAW or when ordering repair parts. PAGE 4 KEY NOS. 19-22 AND 41-42 1
Always mention the model ... model number will be found on a plate attached to the back panel of the cabinet. RYOBI Table Saw -
PAGE 2 KEY NOS. 13 AND 16;
Repair Sheet - Page 7
NUMBER
DESCRIPTION
QTY. RYOBI Table Saw - PARTS LIST FOR FIGURE C
KEY PART KEY PART
NO. NUMBER
DESCRIPTION
QTY.
1 0101210210 LOWER BLADE GUARD 1 2 451020004 WIRE CONNECTOR 2 3 0101140703 MOTOR CORD 1...00)
NO. Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. MODEL NUMBER BTS12S
The model number will be found ...
Repair Sheet - Page 8
... x 1-5/8 in 4
11 411062701 HEX NUT (1/4-20 4
8 MODEL NO. BTS12S
Figure D
3
6
7
9
4
10 9 6
11
8 9 7
5 8
3
2
3
5
4
9
2
2
8 3
2
PARTS LIST For FIGURE D
Key Part
Key Part
No. No. Description
Qty.
RYOBI TABLE SAW -
Repair Sheet - Page 9
MODEL NUMBER BTS12S
POWER CORD
BLACK WHITE
SWITCH
BLACK WHITE
MOTOR CORD
MOTOR
WIRING DIAGRAM
9 RYOBI Table Saw -
Similar Questions
Ryobi 10" Table Saw Dado Throat Plate
where can I find a dado throat plate for the Ryobi 10" table saw?
where can I find a dado throat plate for the Ryobi 10" table saw?
(Posted by Rick52757 2 years ago)
How Do I Remove The Height Wheel On My Rst10 Table Saw?
(Posted by ricosflooring03 8 years ago)
Wiring Diagram For Ryobi Rts21 Table Saw Switch
I need to view the wiring diagram for the switch on the Ryobi RTS21 table saw. I had to disconnect t...
I need to view the wiring diagram for the switch on the Ryobi RTS21 table saw. I had to disconnect t...
(Posted by wolfsonjames 9 years ago)
Dado Blade Insert For A Ryobi Rts10 Table Saw
Where can I purchase a dado blade insert for my Ryobi RTS10 10" table saw? I am having difficulty fi...
Where can I purchase a dado blade insert for my Ryobi RTS10 10" table saw? I am having difficulty fi...
(Posted by bstilton 9 years ago)
