Ryobi RTS10 Support Question
Find answers below for this question about Ryobi RTS10.Need a Ryobi RTS10 manual? We have 4 online manuals for this item!
Question posted by sdighello1 on April 25th, 2014
Can You Install A Dado Set On A Ryobi Rts10 Table Saw
The person who posted this question about this Ryobi product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related Ryobi RTS10 Manual Pages
English Manual - Page 1
... properly cared for, it will give you for dependability, ease of injury, the user must read and understand the operator's manual before using
this product. Table Saw
BTS12S
Your table saw has been engineered and manufactured to our high standard for your purchase.
English Manual - Page 5
...Wear eye protection. d) Use a push stick when required. To minimize risk of using the table saw table for wide or long work pieces.
AVOID KICKBACKS (work that are not listed may...including all fences and auxiliary tables before it can pull your hand into the cutting tool.
Use only recommended accessories listed in line with the path of the saw blade.
NEVER...
English Manual - Page 9
... cutterhead with the blade. Dado Cut A non-through the thickness of the workpiece. Kickback A hazard that the tip of the saw blade tooth is bent (or set) outward from the face ...(radial arm and table saws) A device which, when properly installed and maintained, is designed to stop the workpiece from being kicked back toward operator.
Riving Knife/Spreader/Splitter (table saws) A metal piece...
English Manual - Page 11
... requires an understanding of the information on the front of the cabinet, locks the angle setting of the cabinet. BLADE ADJUSTING HANDLE -
When the locking lever is used to prevent ... - The safe use blades rated less than the saw table shows the distance between the rip fence and the blade. Failure to use the tool.
11 Always keep the kerf open and prevent kickback...
English Manual - Page 12
... the OFF position before operating the switch to start the tool. SWITCH ON
SWITCH OFF
SWITCH KEY
removed
Fig. 3
12
Failure to heed this tool. Your table saw turned OFF, pull the switch key from accidentally starting , Always make sure your saw: With the saw is in personal injury.
Failure to heed this warning may...
English Manual - Page 15
Leg 4 D. Lower Side Brace 2 E. Carriage Bolt (5/16-18 x 5/8 in 4 H. Carriage Bolt (1/4-20 x 1-5/8 in 16 G. Hex Nut 16
I . Lower Brace 2
15 Upper Side Brace 2 B. Upper Brace 2 C. Hex Nut 4 I
Fig. 3
F. Foot 4 J. LOOSE PARTS LIST
The following items are included with the table saw leg stand: C
A G
B
E
D
H
J F
E B
E A
F
C
I
C
J
D
E
I
I
F C
A.
English Manual - Page 16
... are the front and back sets.
For the side sets, install an upper side brace on ...tool. NEVER operate the saw on a level work surface. Inspect the tool carefully to specific procedures explained in this warning can result in serious personal injury. Lower Brace
hex nut
foot
LEG
carriage bolt Fig. 6
16 If shipping has influenced the settings, refer to make sure the table saw...
English Manual - Page 17
...THE leg stand on the table saw base.
Do not lift the saw base weighs approximately 42 lbs.
TO INSTALL THE Blade Adjusting Handle
See Figure 8. Align the holes in the table with the holes in the ...assembling the leg stand and leveling feet.
Place the leg stand on the TABLE saw base, lock washers, hex nuts, and the thickness of the workbench.
Ignoring these ...
English Manual - Page 20
...the same operation.
Always use clean, sharp, and properly-set
blade
AVOIDING KICKBACK
Always use the rip fence when rip ... a workpiece through cuts. Have the correct outlet installed by recessed screws from scrap wood to resist kickback should clear...of this tool. Refer to the Electrical section of the TABLE Saw
The 3-prong plug must be ready to use this tool for ...
English Manual - Page 24
...blade. Scale
Scale indicator
2 in angled cuts. TO INSTall the Rip Fence
See Figure 22. Place the rear lip on the rear of the saw . Loosen the rip fence by depressing the... Using a framing square, set the rip fence scale indicator to set the rip fence 2 in. TO use the following steps to the blade: Unplug the saw table and pull
slightly toward the front of ...
English Manual - Page 25
...scrap wood first.
Keep the miter gauge firmly against the saw is a high-quality combination blade suitable for the workpiece.
Set the miter gauge to a complete stop before moving the
... heed this tool. operation
MAKING CUTS
The blade provided with the saw table as the workpiece is fed into the blade.
WARNING:
Make sure the blade guard assembly is installed and working ...
English Manual - Page 26
...
rip cut
Fig. 27
WARNING:
Make sure the blade guard assembly is installed and working properly to avoid serious personal injury.
Remove the rip...set to the correct depth for the blade to come to a complete stop before removing any part of the workpiece. Keep the workpiece flush against the miter gauge.
Stand slightly to the side of the wood as saw table) behind
the table saw...
English Manual - Page 27
... in kickback and the risk of injury should be placed on the saw.
Turn the saw ON. Let the saw OFF. Keep the workpiece flush against the miter gauge. Stand slightly to the side of the wood as saw table) behind the saw for the blade to come to avoid serious personal injury.
27...
English Manual - Page 29
....
note: Always use of cut is made , turn the saw OFF. Wait for the workpiece. Plug the saw into the blade. DO NOT install dado blades on this section on non-through cut that is essential to... the two
socket head cap screws, lock washers, and flat washers. Set the blade to 0º. Set the blade to avoid the risk of the cut
See Figure 32. Once all non...
English Manual - Page 34
... Table Saw
BTS12S
WARNING:
Some dust created by power sanding, sawing,... grinding, drilling, and other construction activities contains chemicals known to the motor housing. Be sure to provide all pertinent facts when you do this tool will be found on how often you call 1-800-525-2579 for your tool... NUMBER • SERIAL NUMBER
BTS12S
RYOBI® is a registered trademark of...
Repair Sheet - Page 3
...Qty.
1 410282702 SCREW (3/16-24 x 3/8 in all correspondence regarding your TABLE SAW or when ordering repair parts. HD.)...... 1
10 410012702 SCREW (1/4-20 x ...22 410162003 SCREW (M6 x 18 mm CHEESE HD.)...... 3 23 A101014304 BRACKET ASSEMBLY 1 24 089015001002 SAW TABLE 1 25 0101010301 THROAT PLATE INSERT 1 26 410192001 SCREW (M4 x 10 mm TRUSS HD.)......... ...
Repair Sheet - Page 5
....
PARTS LIST FOR FIGURE B
KEY PART KEY PART
NO. PAGE 2 KEY NOS. 13 AND 16; Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. NUMBER
DESCRIPTION
QTY. PAGE 4 KEY NOS. 19-22 AND 41-42...
Repair Sheet - Page 7
Always mention the model number in all correspondence regarding your TABLE SAW or when ordering repair parts. RYOBI Table Saw - PARTS LIST FOR FIGURE C
KEY PART KEY PART
NO. KEY NOS. 18-19 1 21 0101010102 GEAR HOUSING 1 22 420110004 NEEDLE BEARING 3 23 A101010501 JACKSHAFT ASSEMBLY (...
Similar Questions
Dado Blade Insert For A Ryobi Rts10 Table Saw
Where can I purchase a dado blade insert for my Ryobi RTS10 10" table saw? I am having difficulty fi...
Where can I purchase a dado blade insert for my Ryobi RTS10 10" table saw? I am having difficulty fi...
(Posted by bstilton 9 years ago)