Ryobi DP102L Support Question

Find answers below for this question about Ryobi DP102L.
Need a Ryobi DP102L manual? We have 4 online manuals for this item!

Ryobi Overview Questions Manuals Reviews Videos Research

Question posted by revdocpop1 on May 9th, 2016

Belt Not Driving Chuck.

In fact, I can hold the chuck still while the motor and belt are working. I looked in the manual and under assembly, it said to turn the head upside down and hit the chuck with a hammer, suitably shielded. I took the head off and tried that, but it had no effect. What should I do next

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by BusterDoogen on May 9th, 2016 4:00 PM

This answer was accepted by the poster of the original question.

BusterDoogen

Member since:
October 30th, 2011

Points: 28,565,407

1,100
points

Go to page 22 and notice the tension bolt. You need to adjust the belt to tighten it or you may have to replace the belt.

I hope this is helpful to you!

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!

Related Ryobi DP102L Manual Pages

English Manual - Page 1

... give you for dependability, ease of injury, the user must read and understand the operator's manual before using this product. Thank you years of rugged, trouble-free performance. SAVE THIS MANUAL FOR FUTURE REFERENCE DRILL PRESS DP102l Your drill press has been engineered and manufactured to our high standard for your purchase. OPERATOR...

English Manual - Page 2

...90) days or less. We will complete the work properly due to defective workmanship or materials by returning the power tool to two years from misuse, abuse, neglect, alteration...Glossary of Terms...9  Features...10-11  Tools Needed...11  Loose Parts...12  Assembly...13-17  Operation...18-20  Adjustments...21-...

English Manual - Page 3

... comes to contain long hair.  ALWAYS WEAR SAFETY GLASSES WITH SIDE SHIELDS. Check for lubricating and changing accessories.  DISCONNECT TOOLS. Feed work area well lit.  KEEP CHILDREN AND VISITORS AWAY. TURN THE POWER OFF. Don't leave tool until it to hold work area. Wear a face or dust mask if the cutting operation is used...

English Manual - Page 5

...work on the table while the cutting tool is clamped tight to filter out microscopic particles. Do not turn the motor switch ON or start any loose clothing, jewelry, long hair, etc., that the head... to column and head and table support collars are not suitable for laser use to instruct other masonry products, and • arsenic and chromium from the chuck before checking that ...

English Manual - Page 8

... conductor to reduce the risk of the working with a qualified electrician or service personnel if the grounding instructions are working with or without yellow stripes is intended for...as important as to overheat. This tool is heavy enough for lights cannot properly carry a power tool motor. Electrical Connection This tool is green with a power tool. WARNING: Keep the extension cord...

English Manual - Page 10

... laser bevel scale lock knob feed handle table adjustment handle base 10 Fig. 2 FEATURES product specifications Chuck 1/2 in . Input 120 Volt, 60Hz, AC Only, 3 Amps Motor 1/4 HP Induction No Load Speed 570-3,050 r/min. (RPM) Swing 10 in . Spindle Travel 2-3/8 in . Table Movement 45° bevel, 360° swivel Overall Height ...

English Manual - Page 11

...work area. Motor Your drill press is tilted. table The table of material including wood, plastic, and metal. worklight The integrated worklight can be used to aid in the chuck... duty induction motor for assembly and alignment: mallet or hammer adjustable wrench ...chuck and bit during the drilling operation. TOOLS NEEDED The following tools (not included) are needed for long-lasting...

English Manual - Page 12

... included with the drill press: Head Assembly 1 Column Assembly 1 Table Assembly 1 Base 1 Hex Key (3 mm, 4 mm, and 5 mm 3 Hex Bolts (M8 4 Feed Handles 3 Table Adjustment Handle 1 Table Lock Handle 1 AA Batteries 2 Chuck 1 Chuck Key 1 Worm Gear 1 Operator's Manual (not shown 1 aa batteries chuck KEY table assembly chuck worm gear head assembly table lock handle table adjustment...

English Manual - Page 15

... help illuminate the work area. Fig. 9 head assembly set screws with the chuck positioned over the table. Note: This tool is heavy. The integrated worklight can be fully opened to avoid damaging jaws.  Using a piece of scrap wood to protect the chuck, firmly tap the chuck into place using a mallet or hammer.  Position the head assembly onto the...

English Manual - Page 17

... adjustment knobs located on opposite sides of the head assembly.  Mark an "X" on a piece of scrap wood.  Insert a small drill bit into the chuck and align its tip to the intersection of ...the lines of the "X".  Secure the board to ensure the intersection of the "X". Check the laser alignment to the table.  Turn on...

English Manual - Page 19

... bit to loosen or tighten the chuck using chuck key provided. WARNING: Do not .... 17 TABLE assembly Fig. 18 Fig. 19 19 The self-ejecting chuck key ensures the chuck key is removed...chuck or counterclockwise to a point where the open- Always remove chuck key. The table can be thrown from the chuck... use .  Insert drill bit into the chuck the full length of the way when drilling large ...

English Manual - Page 20

...manual.  Set table assembly to Adjusting Table Height in the Adjustments section of this manual....not in the Adjustments section of this manual.  Make sure the work .  Once the hole is...and the bits will automatically raise the chuck and bit. To protect the top ...  Plug electrical cord into power supply and turn switch ON. For large holes, drill a pilot hole...

English Manual - Page 21

...bevel scale to tilt the table to 45º. adjusting table height See Figure 21.  Hold the table with a tilting table that allows you need to drill a number of holes to exactly... could result in serious personal injury. adjustments WARNING: Before performing any adjustment, make sure the tool is equipped with one hand and loosen the table lock handle.  Rotate the table ...

English Manual - Page 22

.... drive belt SPINDLE PULLEY MOTOR PULLEY TENSION bolt Fig. 24 22 The speed chart located on the pulleys inside the head assembly shows the recommended speed and pulley configuration for each drilling operation. The spindle speed is determined by the location of the belt on the cover inside the head assembly. To change the pulley configuration:  Lift head assembly...

English Manual - Page 24

... manual. Install bit properly. Workpiece not supported or clamped Check support and/or reclamp properly workpiece. 24 Retract bit frequently to cut. Excessive feed pressure Improper belt tension Reduce feed pressure. Adjust belt tension. Tighten set screws in chuck Chuck not properly installed Worn spindle bearings Replace bit. Lubricate bit for metal work. Install chuck...

English Manual - Page 26

... 29625 Tel.:1-800-525-2579 www.ryobitools.com 26 DRILL PRESS DP102l • SERVICE Now that you call 1-800-525-2579 for a complete list of this tool will be found on a plate attached to provide all pertinent facts when you have purchased your tool, should a need ever exist for repair parts or service, simply...

Repair Sheet - Page 2

.... For the service center nearest you call 1-800-525-2579. RYOBI 10 in. MODEL NUMBER DP102L 60 59 99 98 61 97 66 16 43 21 62 90 34 90 63 55 64 65 ...24 106 88 87 89 5 10 11 12 25 21 23 22 4 13 19 14 3 18 2 1 NOTE: The assembly shown represents an important part of alteration or damage to the system, service should be performed by your nearest Ryobi Authorized Service Center...

Repair Sheet - Page 3

...FOR FIGURE A PART NUMBER DESCRIPTION QTY. 13103006M1 CHUCK KEY 1 13103006M CHUCK 1 13203001A SPINDLE SHAFT 1 089140200004 BALL BEARING ... SCREW (M8 X 8 mm HEX HD 1 089140200049 HEAD STOCK 1 089140200050 BATTERY BOX 1 TDP06002 * HEX NUT...Purchased Locally MODEL NUMBER DP102L The model number will be found on a plate attached to the motor housing. DRILL PRESS -...

Repair Sheet - Page 4

...DP102L The model number will be found on a plate attached to the motor housing. RYOBI 10 in 1 089140200912 LASER LABEL 1 089140200094 CAPACITOR (DP102 MOTOR 1 089140200096 WASHER 5 983000641 OPERATOR'S MANUAL 06-06-08 (REV:05) * Standard Hardware Item - HD 1 089140200070 MOTOR... MOTOR PULLEY 1 089140200067 * SCREW (M4 X 8 mm PAN HD 4 089140200068 BELT TENSION...

Repair Sheet - Page 5

DRILL PRESS - MODEL NUMBER DP102L WHITE BLACK M WHITE GREEN ~ BLACK GREEN BLACK (SMOOTH) TO CENTER BLACK (RIDGE) TO EDGE WHITE RED LASER RED WHITE LASER WIRING DIAGRAM RYOBI 10 in.