Ryobi CFS1503K Support Question
Ryobi CFS1503K Support Question
Find answers below for this question about Ryobi CFS1503K.Need a Ryobi CFS1503K manual? We have 4 online manuals for this item!
Question posted by donaldvicknair on March 17th, 2014
Ryobi Cfs1503 Sander Platen
where can i find one>?
Current Answers
Related Ryobi CFS1503K Manual Pages
English Manual - Page 1
CORNER CAT® COMPACT FINISH SANDER
Double Insulated CFS1503
Your finish sander has been engineered and manufactured to our high standard for your purchase.
Thank you years of rugged, trouble-free performance. When properly cared for, it ...
English Manual - Page 2
...the above limitations and exclusions may also have been given top priority in any RYOBI® power tool which it easy to two years from the date of the original purchase. ...purchase and return all defects in workmanship or materials in this product making its RYOBI® power tools with the original product. One World Technologies, Inc. Batteries are limited to maintain...
English Manual - Page 3
... properly used for misalignment or binding of moving parts.
If devices are provided for outdoor use common sense when operating a power tool. This enables better control of the power tool in . Do not wear loose clothing or jewelry. Stable footing on a ladder or unstable support. Check for appropriate conditions will increase...
English Manual - Page 4
... parts or failure to determine that it must read instruction manual.
When servicing a power tool, use the next heavier gauge. Following this manual. A guard or other part that the safety..., and any other part that may use of serious personal injury.
Inspect power tool cords periodically and, if damaged, have only impact-resistant lenses; A cord exceeding 100 feet...
English Manual - Page 6
... a situation that may result in property damage.
Always use this product. Call Ryobi customer service for repair.
SYMBOLS
The following signal words and meanings are intended to...which , if not avoided, could result in death or serious injury.
Before beginning power tool operation, always wear safety goggles or safety glasses with side shields.
WARNING:
Indicates a ...
English Manual - Page 7
...grounded power cord. ELECTRICAL
DOUBLE INSULATION
Double insulation is a concept in safety in the tool's internal insulation. Always use an extension cord that it for loose or exposed wires ...UL) should be grounded.
WARNING:
Check extension cords before each use the product with a power tool. WARNING:
The double insulated system is 120 volts, 60 Hz, AC only (normal household ...
English Manual - Page 8
...BAG
The dust bag collects dust through punched holes in . gripzone™ overmold technology
The sander features GripZone™ overmold technology for producing a fine finished grain or, when using the ...design allows for proper fit and alignment. CIRCULAR SANDING Action
The oscillating action of the sander produces very quick, small circular motion of the information on the product and in ...
English Manual - Page 9
.... Natural abrasives, such as flint and garnet are replaced.
Corner Cat® Compact Finish Sander 60-grit Sanding Sheet (2) 120-grit Sanding Sheet (3) 240-grit Sanding Sheet (2) Heavy-...LIST
5-1/2 in serious personal injury.
Always continue sanding with side shields when operating power tools. n Carefully remove the product and any parts are included. n Inspect the product ...
English Manual - Page 10
...
Fig. 3
off . Sanding dust is recommended that you keep the sanding sheet backing clean to turn sander on. Push the ON/OFF switch to the right to provide for the sander. While holding the tool in hook-and-loop type sanding sheet with a light brush. CFS1501-38) 60-grit sanding sheet...
English Manual - Page 11
... too long as corners and crevices, use the tip of the sanding disc surface is in front and away from the sander and sanding area. Do not sand on lumber, tools, or other objects during sanding.
Secure the workpiece to a complete stop. sanding in inferior work . If this occurs, turn...
English Manual - Page 12
...the dust bag every 10-15 minutes while sanding. For a more than half full to the sander.
The punched holes must align with the holes in sandpaper. Always empty and clean the dust ...linseed oil, etc. OPERATION
Emptying the Dust Bag
See Figure 7. WARNING:
Collected dust from the sander. Shake out the dust. Reattach the dust bag to permit better air...
English Manual - Page 13
..., penetrating oils, etc., come in contact with plastic parts. Press the sheet firmly onto the sander pad. Use of commercial solvents and may be damaged by rinsing the pad with a sufficient amount...Chemicals can be rotated. To clean sanding sheets, rub the sheets with side shields during power tool operation or when blowing dust. The unique Tri-Flex design of the base.
Rotate the sheet...
English Manual - Page 14
... replacement parts, please obtain your model and serial number from these chemicals: work in . RYOBI® is a registered trademark of these chemicals are specially designed to filter out microscopic particles... please contact us at 1-800-525-2579. CORNER CAT® COMPACT FINISH SANDER
Double Insulated
CFS1503
WARNING:
Some dust created by calling 1-800-525-2579. Replacement parts can be...
Repair Sheet - Page 2
... to the motor housing. RYOBI CORNER CAT SANDER - Always mention the model number in all correspondence regarding your CORNER CAT SANDER or when ordering repair parts.
5 6 7
4
Key No.
1 2
3 4 5 6 7 8 9
8
3
2
1
PARTS LIST
Part
Number
Description
Qty. May Be Purchased Locally
CFS1501-01
* SCREW (M4.2 x 8 mm 4
039065005001
PLATEN 1
CFS1501-32 PAPER PUNCH...
Similar Questions
Where Can I Get A Dust Bag For Bd4601/bd4601g Belt/disc Sander
(Posted by bigdogduris1 6 months ago)
Has This Sander Literally Blown Apart For Other Users?
The die cast rotating disk in my sander blew apart into four major pieces all of a sudden...explodin...
The die cast rotating disk in my sander blew apart into four major pieces all of a sudden...explodin...
(Posted by donburzen 2 years ago)
Sander Stops Working On Sanding Surface
sander stops spinnig as soon as it goes onto sanding surfsce but starts again when it is lifted up
sander stops spinnig as soon as it goes onto sanding surfsce but starts again when it is lifted up
(Posted by Greenoneil40 3 years ago)
I'm In Canada And Need A Platen For My Ryobi Palm Sander S652d.
Is there a source for this part in Canada??I refuse to pay $35.00 to ship a $4.50 part from the sta...
Is there a source for this part in Canada??I refuse to pay $35.00 to ship a $4.50 part from the sta...
(Posted by balljoynt42 11 years ago)
I Need To Put A 'regular' Piece Of Sandpaper On The Sander.
The manual doesn't really explain how to putsandpaper on the sander.My other sanders have clips or c...
The manual doesn't really explain how to putsandpaper on the sander.My other sanders have clips or c...
(Posted by bmvlak 12 years ago)