Ridgid 1822-I Support Question
Ridgid 1822-I Support Question
Find answers below for this question about Ridgid 1822-I.Need a Ridgid 1822-I manual? We have 1 online manual for this item!
Question posted by Hmdjustin on February 6th, 2013
Ridgid 1822-i Pipe Threader Won't Turn On And Humms When You Try To Turn On Swit
my pipe threader humms when you try to turn it on and won't run the machine. How do I fix ?
Current Answers
Related Ridgid 1822-I Manual Pages
Owners Manual - Page 1
Read this Operator's Manual carefully before using this manual may result in electrical shock, fire and/or serious personal injury. pág. 51
WARNING! Failure to understand and follow the contents of this tool. 1822-I Pipe and Bolt Threading Machine
OPERATOR'S MANUAL
• Français - 25 • Castellano -
Owners Manual - Page 2
1822-I Pipe and Bolt Threading Machine
Table of Contents
Recording Form for Machine Serial Number ...1
General Safety Information Work Area Safety ...2 Electrical Safety ...2 Personal Safety...2 Tool Use and Care ...3 Service ...3
Specific Safety Information Foot Switch Safety ...3 Machine...Dies...16 Operating No. 141 Geared Threader ...16 Threading 21/2″ to 4″ Pipe (45 RPM) ...16
No. ...
Owners Manual - Page 4
...edges or moving parts. 1822-I Pipe and Bolt Threading Machine
General Safety Information
WARNING!
Power tools create sparks which accept the machines plug. Never use common sense when operating a power tool. These cords are ...hair. Keep your body is OFF before turning the tool ON. Be sure switch is grounded.
• Don't expose electrical tools to lose control.
• Keep ...
Owners Manual - Page 5
...machine without a foot switch increases the risk of the tool. Because the machine has high torque, the clothing itself can result in serious injury.
• Keep covers in use if switch does not turn...Operate machine from the power source before using the 1822-I Pipe and Bolt Threading Machine
ables better control of the tool in the hands of untrained users.
• Check for one tool may...
Owners Manual - Page 6
...
Model No.
1822-I Pipe and Bolt Threading Machine
Figure 1 - High Speed Dies are mounted in self-opening, quick-opening die heads or semi-automatic die heads. Locked Foot Switch
Description, Specifications and Standard Equipment
Description
The RIDGID Model 1822-I Threading Machine can also be used with thread cutting oil during threading operations. Geared Threaders can also be...
Owners Manual - Page 8
1822-I Pipe and Bolt Threading Machine... of the base. CAUTION For proper balance and operation, RIDGID machines must be mounted through the appropriate holes in the detail drawing...Machine Dimensions
shown in the rails (Figure 3). Detail Section
Figure 3 - No. 1406 Folding Wheel Stand
6
Ridge Tool Company Stand Assembly
3/8″ - 16 x 21/2″ Bolt 4 Required
NOTE! Mount machine...
Owners Manual - Page 9
...machine oil
reservoir and prevents oil spill during transportation. 1822-I Pipe and Bolt Threading Machine
Mounting Machine to prevent oil spillage.
2.
Chip pan will not lock into a compact package.
3. Transporting Machine...machine and top stand rails and lift machine...and machine is not used, the machine should...machine and above cabinet or tray.
2.
Ridge Tool Company
7 Place machine...
Owners Manual - Page 10
... performed on a daily basis:
1. WARNING Do not operate the Threading Machine without a foot switch. 5.
Foot Switch
Figure 7 - 1822-I Pipe and Bolt Threading Machine
CAUTION DO NOT use with other conditions which may be hazardous when used with a wire brush. 3. If any of your tools and dies. Use tools and accessories that are designed for your Threading...
Owners Manual - Page 11
... the cord's insulation or causing nearby objects to the directional switch and tools without reaching across the machine. Clean up any equipment. This "safety zone"
prevents others from the... outlet, use RIDGID Stainless Steel Oil and thread at 45 RPM. WARNING To reduce risk of the pipe.
4. NOTE! NOTE! Machine is required. 1822-I Pipe and Bolt Threading Machine
NOTE! High speed...
Owners Manual - Page 12
...
4. 1822-I Pipe and Bolt Threading Machine
• Depress and hold down the foot switch with the left foot.
10
Ridge Tool Company ...machine and tools.
• Be sure you have the machine serviced.
• Flip the control switch to release pipe and rechuck.
Slight off -center, run the machine in 45 RPM position.
4. Tighten cutter feed screw handle on pipe.
3. The machine...
Owners Manual - Page 13
...pipe is flush with left foot
and feed carriage handwheel towards pipe. 3. Failure to release the dies from the pipe.
7. Threading Pipe with Self-Opening, Quick-Opening, or Semi-Automatic Die Head
1.
1822-I Pipe and Bolt Threading Machine
7. Move reamer arm into pipe...8243; pipe, die head must be opened .
Turn carriage handwheel to UP position. 3. Ridge Tool Company...
Owners Manual - Page 14
1822-I Pipe and Bolt Threading Machine
8.
Depress foot switch and machine will lock in vertical position, rotate cam plate until index line on lock screw is supported prior to a power source. WARNING Never reach inside chuck cover while machine... six full turns.
4. Lay die head down with proper size mark on the die head.
8. NOTE! Removing Pipe From The Threading Machine
1. Clean up...
Owners Manual - Page 15
...turn of being flush with the numbers facing up.
3. Flip throwout lever to thread pipe ranging from 1/8″ through 2″. Model 816/817 Die Head) against the die head.
7. Rotate the handle clockwise (to mark on side of ring gage. One set the index line in slot under size bar. Ridge Tool... on the dies -
1822-I Pipe and Bolt Threading Machine
NOTE! Slide throwout lever...
Owners Manual - Page 16
... Large One Turn Small
(Basic Size) (Maximum Size) (Minimum Size)
B - WARNING Remove wrench before starting machine.
5. Checking Threads Within Pipe Gage
Figure 14 - Make sure that special front retainer plate is installed to Cut Thread
Completed Thread
A - Nipple Chuck
Insert
Wrench
Adapter
Figure 16 - NOTE! 1822-I Threading Machine. Checking Thread Length
No. 819 Nipple...
Owners Manual - Page 17
... Line
Guide Post
Screw
Gear Case
Figure 19 - No. 141 Geared Threader showing Pinion Sleeve and Guide Post Reference Lines
Indexing Guide Post For Straight Or Tapered Threads (Figure 19)
1. Ridge Tool Company
15 1822-I Pipe and Bolt Threading Machine
Operation Instructions Using Geared Threaders
WARNING
Reference Lines (3)
Guide Post Head
Drive Shaft
Do not wear...
Owners Manual - Page 18
... tube up to standard line. 1822-I
Threading Machine.
2. Replace stop line appears on 1822-I Pipe and Bolt Threading Machine
3. If it must be bent/broken.
5. With guide block in the OPEN position and depress foot switch.
8. Tighten connecting link set screws. Insert pipe into the throat of No. 141. To back off threader, place control switch in...
Owners Manual - Page 19
... cutter over pipe and with machine in Figure 21.
CAUTION Both front and rear jaws must be in left hand operation. Run machine in the ...pipe and other applications. 1822-I Pipe and Bolt Threading Machine
Oil Spout
Connecting Link
Oil Manifold/Lever (Hidden)
Guide Post
Pipe
Drive Shaft (Set Screws)
Pinion Sleeve
Figure 20 - Direct oil spout to the cutting surface and slowly turn tool...
Owners Manual - Page 20
... RIDGID products have been designed to the oil pump fitting marked IN.
2. Reinstall washers and E-Clips on this Threading Machine. NOTE! Before reinstalling machine covers...18
Ridge Tool Company Other accessories designed for use only the accessories listed below. Accessories For Threading Machine
Stands: No. 1406 Folding Wheel Stand with the 1822-I Pipe and Bolt Threading Machine
Figure ...
Owners Manual - Page 21
... are located on top and at each end of oil reservoir removed. Ridge Tool Company
19 Spindle Bearing Lubrication (Figure 22)
Bearing Lubrication Ports
Spindle Housing
Figure 22 - With machine OFF and unplugged, remove front
cover. 3. 1822-I Pipe and Bolt Threading Machine
Model No.
819 819 839 821 822 141 141 241 1460 E-863 364...
Owners Manual - Page 24
... instructions may create a risk of your nearest Independent Authorized Service Center, contact Ridge Tool Company at (800) 519-3456 or http://www.ridgid.com
22
Ridge Tool Company WARNING When servicing this machine, only identical replacement parts should be used. 1822-I Pipe and Bolt Threading Machine
Service and Repair
WARNING
Service and repair work on this Threading...
Similar Questions
Why Did My Ridgid Table Saw Power Die After I Turned It On?
I turned on the power to my table saw and everything died. Tried turning the power switch on and off...
I turned on the power to my table saw and everything died. Tried turning the power switch on and off...
(Posted by georgegll628 2 years ago)
When Turning On It Is Locked Up Due To The Feed Rollers Not Allowing The Cutting
head to turn
head to turn
(Posted by Janthonysupensky 7 years ago)
When I Start It It Just Turns Off
I have a green light when i switch it on but when i start it it just turns off?
I have a green light when i switch it on but when i start it it just turns off?
(Posted by thomas20792 8 years ago)
Why Does Front Jaws Hold Pipe And Back Jaws Come Loose On Any Size Pipe 1822i
(Posted by draytaylor2003 11 years ago)
Why Won't 1'1/4 Pipe Lock In When Cuting Or Treading. It Fine With 1'1/2 & 1'
The machine works fine with all sizes except 1:1/4.. what would cause the one size of pipe not to lo...
The machine works fine with all sizes except 1:1/4.. what would cause the one size of pipe not to lo...
(Posted by daniellundon 11 years ago)