Poulan PDB18H42STA Support Question
Poulan PDB18H42STA Support Question
Find answers below for this question about Poulan PDB18H42STA.Need a Poulan PDB18H42STA manual? We have 1 online manual for this item!
Question posted by james30487 on April 18th, 2014
Installed New Engine. Only Clicks When Ignition Engaged
Is the ammeter the part mounted on the inside of the right hand side withe the two red "leads"? Getting 12v reading to this point and 12v reading beyond to the starter. Is this a repair or replaceable part? Could this be the problem? Thx
Current Answers
Related Poulan PDB18H42STA Manual Pages
User Manual - Page 4
...RULES". CUSTOMER RESPONSIBILITIES
• Read and observe the safety rules. • Follow a regular schedule in effective working order by law (Section 4442 of a new tractor.
In the state ...under "Maintenance" and "Stor- It has been designed, engineered and manufactured to service or repair this owner's manual. Please read and retain this manual). The instructions will enable you cannot...
User Manual - Page 6
...down. • Get off seat without moving...ASSEMBLY
Your new tractor has...Align
mounting holes ...
(left hand is reached...right or left to right) and slide inside boot and onto adapter. • Assemble large flat washer, 1/2 hex nut and tighten
securely. • Snap steering wheel insert into operating position and sit on seat to engage shoulder bolt in extension and lower shafts and install...
User Manual - Page 7
...engine oil level and fill fuel tank with the instructions that gauge wheel bar aligning holes are on top. Continue with gasoline.
• Place freewheel control in "transmission engaged...; Turn ignition key to...read, understand and follow . RETAINER SPRING
eration section for charging instructions). Be sure they are designed to its highest position.
• Start the engine.After engine...
User Manual - Page 8
... AND ENJOYYOUR NEW TRACTOR, WE...grass, but for replacing motion and mower...installation of this manual. TO INSTALL MULCHER PLATE (See Fig. 4B)
NOTE: If you installed the mulching blades you start the engine...install the high performance blades. • Remove mulcher plate and mulcher blades and install
high performance blades, (see that the belts are routed properly around pulleys and inside...
User Manual - Page 9
...IGNITION
ENGINE OFF LIGHTS ON
P
ENGINE ON ENGINE START
PARKING BRAKE
PARKING BRAKE PARKING BRAKE
LOCKED
UNLOCKED
OVER TEMP LIGHT
FUEL
OIL PRESSURE BATTERY REVERSE FORWARD
MOWER HEIGHT MOWER LIFT
15
15
15
ATTACHMENT
ATTACHMENT
CLUTCH ENGAGED CLUTCH DISENGAGED
DANGER, KEEP HANDS... in damage to the tractor and/or engine.
Learn and understand their meaning.
WARNING indicates...
User Manual - Page 10
... CONTROL: Used for starting and stopping the engine.
IGNITION SWITCH: Used for starting the engine. OPERATION
KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR TRACTOR
Compare the illustrations with your tractor.
ATTACHMENT CLUTCH LEVER: Used to engage the mower blades, or other attachments mounted to familiarize yourself with the locations of...
User Manual - Page 11
.... • The average lawn should be mowed twice. mance. For healthier and better looking lawns, mow often and after ...ENGAGED" POSITION
IGNITION KEY
"DISENGAGED" POSITION PARKING BRAKE "ENGAGED" POSITION
CLUTCH/BRAKE PEDAL "DRIVE" POSITION
HEIGHT ADJUSTMENT
MOTION CONTROL LEVER
KNOB
PARKING BRAKE
"DISENGAGED"
POSITION
FIG. 6
STOPPING (See Fig. 6)
MOWER BLADES • To stop engine...
User Manual - Page 12
... Figs. 5 and 9)
When pushing or towing your tractor, be slightly off the ground. • Replace retainer spring into the slot and release
so it is held in the disengaged position. • Do not... slowly. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the ground when mower is absolutely necessary, push clutch/brake
pedal ...
User Manual - Page 13
...leaded gasoline will take extra cranking time to "START" position and release key as soon as described above ) • When engine starts, move the throttle control back to fast position, wait a few seconds, remove and read the warm and cold starting the engine....
• Insert key into ignition and turn key clockwise to move throttle control to the engine.
• Be sure freewheel ...
User Manual - Page 14
...inside the transmission which may need to be adjusted for best mowing performance. Repeat this procedure there will be no movement of drive wheels. See "TO LEVEL MOWER HOUSING" in the Service and Adjustments section of this manual.
• The left hand... the right so ...engage or disengage freewheel lever while the engine is running, move throttle control to reverse position. After the engine...
User Manual - Page 17
....
Replace bent or damaged blades. but are working properly. Do not attempt to mower and engine. ...not function as described, repair the problem immediately. • The engine should not start unless...position. • When the engine is engaged, any maintenance. Do not attempt...at washer securing
FIG. 13
blade.
• Install new or resharpened blade with balancer). Lbs. Care should ...
User Manual - Page 18
... first then RED bat-
Change the oil...tightened securely for accurate reading. C -30
-...engine when changing oil. • Remove yellow cap from end of drain valve and install
the drain tube onto the fitting. • Unlock drain valve by pushing inward and turning clockwise until bright. • Coat terminals with grease or petroleum jelly. • Reinstall battery (See "REPLACING...
User Manual - Page 19
... flow to carburetor, replacement is used to
close. We do not recommend using a dirty air filter. Water in fuel line with arrow
pointing towards
engine. • Remove cover. ...8226; Place new fuel filter in position in engine or transmission will shorten the useful life of this manual.
NOTE: If very dirty or damaged, replace cartridge. • Place new pre-cleaner...
User Manual - Page 20
... in neutral (N) position. • Place attachment clutch in "DISENGAGED" position. • Turn ignition key to raise suspension arms. Slide mower
out from spark plug and place wire where it cannot...to right side of bracket. • Disconnect anti-swaybar from the right side of tractor. • Place attachment clutch in contact
with small retainer spring.
• Install belt onto engine ...
User Manual - Page 22
... front of tractor and roll around the top
groove of engine pulley. • Install belt through stationary idler and clutching
idler. • Make sure belt is necessary. Replace brake pads or contact a qualified service center. Engage parking brake. For assistance, there is mounted on
TO CHECK AND ADJUST BRAKE
bottom side of the...
User Manual - Page 24
... then RED battery
cable and carefully remove battery from tractor. • Install new battery with remaining hex bolt and keps nut.
Tighten securely. Always wear eye protection when around batteries.
DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.
SERVICE AND ADJUSTMENTS
TO START ENGINE WITH A WEAK BATTERY (See Fig. 28)
WARNING: Lead-acid...
User Manual - Page 26
... plug hole(s) into
cylinder(s). • Turn ignition key to "START" position for a few seconds
to distribute oil. • Replace with new spark plug(s). Add stabilizer to gasoline in the... in the tank inside a building where fumes may require
recharging. • To help prevent corrosion and power leakage during storage. Allow the engine to cool before painting. Replace if necessary. &#...
User Manual - Page 27
...Replace fuse. 5. Engine clicks but will not turn over
1. Weak or dead battery. 2. Loose or damaged wiring. 4. Check/replace solenoid or starter. Build-up of adjustment.
1. Spark plug wire loose. 11. Drain fuel tank and carburetor, refill tank with fresh
gasoline and replace fuel filter. 8. Tighten blade bolt. 2. Loose or damaged wiring. 9. Faulty ignition...
User Manual - Page 28
.... 8.
Frozen idler pulley. 4. Blades improperly installed. 10. Clogged mower deck vent holes from buildup of mower housing. 8. Shift to run when operator leaves seat with blades listed in "FAST" position. 2. Level mower deck. 5. Check tires for 30 seconds before stopping engine.
1. Replace with attachment clutch engaged
1.
Faulty light switch. 4. Motion drive belt...
User Manual - Page 46
...purchaser, we will repair or replace, at our option, without charge to you have any products used for replacement under this product...replace, without charge for the movement of any product which has been subjected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product.
6. This warranty does not apply to the engine, other rights...
Similar Questions
Chain Off Sprocket
the chain on my pln3516f came off the sprocket and I can't get it back on. How do i get it back on t...
the chain on my pln3516f came off the sprocket and I can't get it back on. How do i get it back on t...
(Posted by nephron44 3 years ago)
Auger Does Not Spin
I installed new auger belt but as soon as weight of snow gets in it stops spinning, Why
I installed new auger belt but as soon as weight of snow gets in it stops spinning, Why
(Posted by shinipu04 7 years ago)
Wiring Diagram This Has Had 19.1 Briggs Engine Installed
I need the wiring diagram this has had 19.1 Briggs engine installed
I need the wiring diagram this has had 19.1 Briggs engine installed
(Posted by ocrgpa 9 years ago)
The Blade Engage/disengage Knob Pulled Off. How Do I Get A New One??
(Posted by cspayne 9 years ago)