Poulan PDGT26H48C Support Question
Poulan PDGT26H48C Support Question
Find answers below for this question about Poulan PDGT26H48C.Need a Poulan PDGT26H48C manual? We have 1 online manual for this item!
Question posted by cspayne on June 18th, 2014
The Blade Engage/disengage Knob Pulled Off. How Do I Get A New One??
The person who posted this question about this Poulan product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Poulan PDGT26H48C Manual Pages
User Manual - Page 2
... to loss-of the machine.
Adjust and service
• Avoid starting . tion, disengage the blades and proceed slowly straight
down before dismounting. I.
Reduced traction could be picked up which...- Check their ability to operate the riding mower safely enough to stabilize the machine by the blade.
• Do not mow on the slope. Frequently check
• Follow the manufacturer's...
User Manual - Page 3
... on a slope.
If tires lose traction, disengage the blades and proceed slowly straight down the slope.
• If machine stops while going uphill, disengage blades, shift into reverse and back down a hill...• Never carry children.They may fall off and be seriously injured or interfere with the blades off if children enter the area.
• Before and when backing, look down slopes (...
User Manual - Page 4
... purchase of this manual. Always observe the "SAFETY RULES".
CCA: 280 CASE SIZE: U1R
Blade Bolt Torque:
45-55 FT. Should you experience any ). LBS. CUSTOMER RESPONSIBILITIES
• Read... your tractor.
• Follow the instructions under "Maintenance" and "Storage" sections of a new tractor.
If a spark arrester is used, it should not be maintained in maintaining, caring for...
User Manual - Page 7
...disengaged position to press clutch/brake pedal all the way down. • Get off the skid. Continue with clevis pins and spring retainers.
• Adjust gauge wheels before tightening adjustment knob. • Remove adjustment knob...Roll tractor forward off skid.
• Apply brake to engage shoulder bolt in slot and pull seat towards rear of shoulder bolt is positioned over large ...
User Manual - Page 8
...Engage belt tension rod by pushing rod into electric clutch pulley groove. • Place the suspension arms on level surface and mower suspension arms are positioned in tab holes in mower brackets.
• Position nose roller between front mower brackets. LOCK BRACKET BELT TENSION ROD (DISENGAGED...8226; If equipped, turn height adjustment knob clockwise to remove slack from mower suspension....
User Manual - Page 9
... and drive belts. See that are shown for replacing motion, mower drive, and mower blade drive belts in "PRODUCT
SPECIFICATIONS" section of this manual.
Be sure they are properly clamped...securely.
✓ All tires are routed correctly.
✓CHECKLIST
BEFOREYOU OPERATE AND ENJOYYOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROMTHIS QUALITY...
User Manual - Page 10
... BRAKE
PARKING BRAKE PARKING BRAKE
LOCKED
UNLOCKED
OVER TEMP LIGHT
FUEL
OIL PRESSURE BATTERY REVERSE FORWARD
MOWER HEIGHT
15
MOWER LIFT
15
ATTACHMENT
ATTACHMENT
CLUTCH ENGAGED CLUTCH DISENGAGED
DANGER, KEEP HANDS AND FEET AWAY
KEEP AREA CLEAR
SLOPE HAZARDS
(SEE SAFETY RULES SECTION)
FREE WHEEL (Automatic Models only)
Failure to the tractor...
User Manual - Page 11
...discharging(-). LIFT LEVER PLUNGER -
Locks brake pedal into the brake position. HEIGHT ADJUSTMENT KNOB - MOTION DRIVE BELT TENSION HANDLE - OPERATION
KNOW YOUR TRACTOR
READ THIS OWNER'S MANUAL...engine. Used to engage mower blades or other attachments mounted to adjust the mower height. Used when starting engine under extremely cold conditions.
11
Disengages transmission for pushing or...
User Manual - Page 12
...PUSH IN TO "DISENGAGE"
ATTACHMENT CLUTCH SWITCH PULL OUT TO "ENGAGE"
• Full throttle offers the best mower performance. TO MOVE FORWARD AND BACKWARD
/BRAKE PEDAL
"BRAKE"
02149
POSITION
"DRIVE" POSITION
HEIGHT ADJUSTMENT KNOB
IGNITION KEY
MOTION CONTROL LEVER
"DISENGAGED" POSITION
PARKING BRAKE "ENGAGED" POSITION
(See Fig. 8)
CAUTION: Do not attempt to the blade tip with motion...
User Manual - Page 13
... position. LIFT LEVER HIGHEST POSIITON
LOWEST POSITION
ATTACHEMNT CLUTCH SWITCH PULL OUT TO "ENGAGE"
PUSH IN TO "DISENGAGE"
FIG. 10
02142
DEFLECTOR
SHIELD
TO OPERATE ON HILLS
WARNING...; Start mower blades by engaging attachment clutch
control. • TO STOP MOWER BLADES - TO TRANSPORT (See Figs. 7 and 11)
When pushing or towing your tractor, be sure to disengage transmission by the...
User Manual - Page 14
... brake pedal and set parking brake.
• Move attachment clutch to "DISENGAGED" position.
• Move throttle control to warm up for a few...tank to the engine. • Be sure freewheel control is engaged.
14 This may not be used . Use fresh fuel next...while in your tractor. If the engine starts to run roughly, pull the choke control out slightly for easier starting (See "OIL VISCOSITY...
User Manual - Page 15
... be purged before mowing.
PURGE TRANSMISSION
CAUTION: Never engage or disengage freewheel lever while the engine is running.
• Engage transmission by selecting a low enough gear to give best...being used when the mower housing is attached to tractor.
• Mower should be pulled out slightly. IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD...
User Manual - Page 17
..." section of this manual). Care should never operate unless the operator is in the disengaged position. • When the engine is running and the attachment clutch is maintenance free...tire dry rot and corrosion. If your tractor is engaged, any attempt by turning counterclockwise.
• Install new or resharpened blade with an automotive charger will cause excessive vibration and ...
User Manual - Page 19
...transmission will not run properly using a garden hose or pressure washer to clean your tractor.
Water in one year. FIG. 17
19 Clean with
knobs. CLEAN AIR INTAKE/COOLING AREAS
To insure.... tions. • Place new fuel filter in position in "PRODUCT SPECIFICATIONS" section of all times. THEY MAY CAUSE DETERIORATION OF THE CARTRIDGE. KNOBS
COVER
CARTRIDGE
FOAM PRE-CLEANER
...
User Manual - Page 20
...anged pin, the hole in contact
with plug.
Engage parking brake.
• Swing anti-sway bar...blades and all moving parts have completely stopped. • Disconnect spark plug wire from spark plug and place wire where it stops.
• Lower mower linkage with attachment lift control.
• Be sure belt tension rod is in "DISENGAGED" position. • If equipped, turn height adjustment knob...
User Manual - Page 21
...; Before making any blade so the tip is spring loaded. NOTE: Each full turn height adjustment knob clockwise to remove slack from trunnion on
both front links. "B" by pushing rod into locking bracket. SERVICE AND ADJUSTMENTS
• Engage belt tension rod by approximately 3/16". • When distance "B" is 1/8" to 1/2" lower at front than...
User Manual - Page 22
... all grooves properly. BELT TENSION ROD(DISENGAGED POSITION)
RH MANDREL COVER
ELECTRIC CLUTCH PULLEY
SPRING ARM
IDLER PULLEYS
R.H. REMOVE MOWER DRIVE BELT
(Refer to primary idler arm
and spring arm. mandrel pulley. • Remove belt from lock bracket. INSTALL NEW MOWER BLADE (SECONDARY) DRIVE BELT • Install new belt in this section of R.H. Have...
User Manual - Page 23
... spring.
• Reinstall mower.
NOTE: After installing a new electric clutch, run tractor at the factory and adjustment should be sure belt is positioned correctly and is on level surface.
Engage parking brake. Pull freewheel control out and into all the way down and engage parking brake. • Disengage transmission by turning ignition key to be...
User Manual - Page 27
... 4. Water in Service Adjustments
section. 8. Attachment clutch is engaged. 3. Loose or damaged wiring. 4.
See "To Adjust...filter. 8. Loose or damaged wiring. 7. Disengage attachment clutch. 3. Check all wiring. 7.
Clean/replace...battery terminals. 3. Loose or damaged wiring. 14. Bent blade mandrel. 3. Dirty fuel filter. 5. Carburetor out ...
User Manual - Page 28
....
1. Mower drive belt worn. 9. Place throttle control in "engaged" position. 2. Replace with attachment clutch engaged
1. Clean around mandrels to open vent holes. Faulty light switch....run when operator leaves seat with blades listed in "disengaged" position. 2. Replace blade mandrel. 5. Replace idler pulley. 4. Wet grass. 4. Blades improperly installed. 10. Headlight(s)...
Similar Questions
Blade Engagement
I have used my Poulon Pro only about four times. Now the blade will not engage.
I have used my Poulon Pro only about four times. Now the blade will not engage.
(Posted by Quila68 7 years ago)
Cord To Engage Blades
What is the part name and replacement number for the cord that runs from the handle to engage or une...
What is the part name and replacement number for the cord that runs from the handle to engage or une...
(Posted by stephaniewoolfolk 8 years ago)
Poulan Pro Ppr2042sta Won't Run When You Engage The Blade Or Let The Clutch Out
(Posted by tcapaletti 9 years ago)
Installed New Engine. Only Clicks When Ignition Engaged
Is the ammeter the part mounted on the inside of the right hand side withe the two red "leads"? Gett...
Is the ammeter the part mounted on the inside of the right hand side withe the two red "leads"? Gett...
(Posted by james30487 10 years ago)